Unable to use PCMCIA Memory Devices...
Matthew Percival
matthew at capgo.com
Sun Apr 2 19:28:20 EDT 2006
G'Day,
> On Fri, Mar 31, 2006 at 11:19:13AM +1000, Matthew Percival wrote:
> > ide-cs: ide_register() at 0xc2878000 & 0xc287800e, irq 222 failed
>
> Could you post a lspci -vvv, dmesg and the output of "lspcmcia -vv" (you
> need pcmciautils-013 for that), please?
lspci -vvv
pcilib: Cannot open /proc/bus/pci
lspci: Cannot find any working access method.
lspcmcia -vv
Socket 0 Bridge: [omap_cf] (bus ID: omap_cf)
Configuration: state: suspended ready: yes
Voltage: 3.3V Vcc: 3.3V Vpp: 0.0V
Available IRQs: none
Socket 0 Device 0: [ide-cs] (bus ID: 0.0)
Configuration: state: suspended
Product Name: CL ATA FLASH CARD LEXAR TIDALWV V100N
Identification: manf_id: 0x4e01 card_id: 0x0200
function: 4 (fixed disk)
prod_id(1): "CL ATA FLASH CARD LEXAR " (0x144506e2)
prod_id(2): "TIDALWV" (0x7f641c27)
prod_id(3): "V100N" (0x958d1a5b)
prod_id(4): --- (---)
dmesg
pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
OMAP1611b revision 2 handled as 16xx id: c5058f79488e1622
SRAM: Mapped pa 0x00020000 to va 0xd0000000 size: 0x3f000
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200n8 noinitrd ip=on root=/dev/nfs rw nfsroot=10.0.0.12:/data/rootfs2.6,nolock
Clocks: ARM_SYSST: 0x1000 DPLL_CTL: 0x2833 ARM_CKCTL: 0x3000
Clocking rate (xtal/DPLL1/MPU): 12.0/192.0/192.0 MHz
Total of 128 interrupts in 4 interrupt banks
OMAP GPIO hardware version 1.0
MUX: initialized M7_1610_GPIO62
PID hash table entries: 256 (order: 8, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
Memory: 29000KB available (2750K code, 504K data, 120K init)
Calibrating delay loop... 95.83 BogoMIPS (lpj=373760)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
OMAP DMA hardware version 1
DMA capabilities: 000c0000:00000000:01ff:003f:007f
Initializing OMAP McBSP system
USB: hmc 16, usb0 2 wires
i2c_omap: bus 0 rev2.2 at 100 KHz
tps65010: version 2 May 2005
MUX: initialized N14_1610_UWIRE_CS0
MUX: initialized P15_1610_UWIRE_CS3
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NetWinder Floating Point Emulator V0.97 (double precision)
Power Management for TI OMAP.
MUX: initialized T20_1610_LOW_PWR
OMAP OCPI interconnect driver loaded
OMAP DSP driver initialization
omapdsp: mapping in ARM MMU, v=0xe0fff000, p=0x11c54000, sz=0x1000
JFFS version 1.0, (C) 1999, 2000 Axis Communications AB
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
fuse init (API version 7.3)
JFS: nTxBlock = 226, nTxLock = 1813
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
omapfb: configured for panel osk
omapfb-lcdc: init
omapfb-lcdc: Pixel clock divider value is obsolete.
omapfb-lcdc: Try to set pixel_clock to 8000 and pcd to 0 in drivers/video/omap/lcd_osk.c and submit a patch.
MUX: initialized PWL
Console: switching to colour frame buffer device 30x40
omapfb: initialized vram=153600 pixclock 8000 kHz hfreq 20.1 kHz vfreq 63.3 Hz
Real Time Clock Driver v1.12
OMAP RTC Driver
omap_rtc: RTC power up reset detected.
omap_rtc: Enabling RTC.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xfffb0000 (irq = 46) is a ST16654
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <nico at cam.org>
eth0: SMC91C94 (rev 9) at c2876300 IRQ 160 [nowait]
eth0: Ethernet addr: 00:0e:99:02:04:19
eth0: No PHY found
i2c /dev entries driver
TLV320AIC23 I2C version 0.1 (12-Aug-2004)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
omapflash.0: Found 1 x16 devices at 0x0 in 16-bit bank
omapflash.0: Found 1 x16 devices at 0x1000000 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x20000,blocks=128
erase region 1: offset=0x1000000,size=0x20000,blocks=128
Creating 4 MTD partitions on "omapflash.0":
0x00000000-0x00020000 : "bootloader"
0x00020000-0x00040000 : "params"
0x00040000-0x00240000 : "kernel"
0x00240000-0x02000000 : "filesystem"
MUX: initialized W11_1610_CF_CD1
MUX: initialized P11_1610_CF_CD2
MUX: initialized R11_1610_CF_IOIS16
MUX: initialized V10_1610_CF_IREQ
MUX: initialized W10_1610_CF_RESET
omap_cf: cs2 on irq 222
usbmon: debugfs is not available
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OMAP)
MUX: initialized W8_1610_GPIO9
MUX: initialized W4_USB_HIGHZ
ohci ohci: OMAP OHCI
ohci ohci: new USB bus registered, assigned bus number 1
ohci ohci: irq 38, io mem 0xfffba000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
usbcore: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
mice: PS/2 mouse device common for all mice
OMAP Keypad Driver
input: omap-keypad as /class/input/input0
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
FIXME: Clock "tc2_ck" seems unused
Disabling unused clock "tc1_ck"... done
Skipping reset check for DSP domain clock "dsptim_ck"
Skipping reset check for DSP domain clock "dspxor_ck"
Skipping reset check for DSP domain clock "dspper_ck"
OMAP Random Number Generator ver. 20
128 words of entropy generated
eth0: link up
Sending DHCP requests .,., OK
IP-Config: Got DHCP answer from 0.0.0.0, my address is 10.0.0.5
IP-Config: Complete:
device=eth0, addr=10.0.0.5, mask=255.0.0.0, gw=10.0.0.2,
host=10.0.0.5, domain=, nis-domain=(none),
bootserver=0.0.0.0, rootserver=10.0.0.12, rootpath=
Looking up port of RPC 100003/2 on 10.0.0.12
Looking up port of RPC 100005/1 on 10.0.0.12
VFS: Mounted root (nfs filesystem).
Freeing init memory: 120K
pccard: PCMCIA card inserted into slot 0
pcmcia: registering new device pcmcia0.0
Probing IDE interface ide0...
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
Probing IDE interface ide0...
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
Probing IDE interface ide0...
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
Probing IDE interface ide0...
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
Probing IDE interface ide0...
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
Probing IDE interface ide0...
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
Probing IDE interface ide0...
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
Probing IDE interface ide0...
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
Probing IDE interface ide0...
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
Probing IDE interface ide0...
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
hda: probing with STATUS(0x00) instead of ALTSTATUS(0x51)
ide-cs: ide_register() at 0xc2878000 & 0xc287800e, irq 222 failed
-- Matthew
More information about the linux-pcmcia
mailing list