card manager hangs
Fetka Mario
Mario-Fetka at gmx.at
Thu Sep 22 10:05:39 EDT 2005
Hallo all,
Here is the wanted dmesg output:
Linux version 2.6.13-gentoo-r1 (root at tiulk) (gcc version 3.4.4 (Gentoo
3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #1 SMP Tue Sep 20 13:58:21 GMT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fee0000 (usable)
BIOS-e820: 000000003fee0000 - 000000003feea000 (ACPI data)
BIOS-e820: 000000003feea000 - 000000003ff00000 (ACPI NVS)
BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
126MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 261856
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32480 pages, LIFO batch:15
DMI present.
ACPI: RSDP (v000 TOSCPL ) @ 0x000f6bd0
ACPI: RSDT (v001 TOSCPL RSDT 0x06040000 LTP 0x00000000) @ 0x3fee39f5
ACPI: MADT (v001 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x3fee9e88
ACPI: FADT (v001 TOSCPL ALVISO 0x06040000 LOHR 0x00000032) @ 0x3fee9ef0
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x3fee9fd8
ACPI: MCFG (v001 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x3fee9f9c
ACPI: SSDT (v001 SataRe SataPri 0x00001000 INTL 0x20030224) @ 0x3fee490b
ACPI: SSDT (v001 SataRe SataSec 0x00001000 INTL 0x20030224) @ 0x3fee4279
ACPI: SSDT (v001 PmRef Cpu0Ist 0x00003000 INTL 0x20030224) @ 0x3fee3e34
ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x3fee3c56
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030224) @ 0x3fee3a3d
ACPI: DSDT (v001 TOSCPL ALVISO 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:a0000000)
Built 1 zonelists
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192
real_root=/dev/sda3 udev
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
CPU 0 irqstacks, hard=c0496000 soft=c048e000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1862.490 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1031488k/1047424k available (2673k kernel code, 15000k reserved,
730k data, 212k init, 129920k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3729.74 BogoMIPS
(lpj=7459490)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000
00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000
00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00000000 00000000 00000040 00000180
00000000 00000000
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) M processor 1.86GHz stepping 08
Total of 1 processors activated (3729.74 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
Brought up 1 CPUs
checking if image is initramfs... it is
Freeing initrd memory: 1752k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd904, last bus=7
PCI: Using MMCONFIG
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: Embedded Controller [EC0] (gpe 29)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 8 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
pnp: 00:00: ioport range 0xfe00-0xfe7f has been reserved
pnp: 00:00: ioport range 0xfe80-0xfeff has been reserved
pnp: 00:00: ioport range 0xff00-0xff7f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 3000-3fff
MEM window: b8100000-b81fffff
PREFETCH window: c8000000-cfffffff
PCI: Bridge: 0000:00:1c.0
IO window: 4000-4fff
MEM window: bc000000-bfffffff
PREFETCH window: d0000000-d3ffffff
PCI: Bridge: 0000:00:1c.1
IO window: 5000-5fff
MEM window: c0000000-c3ffffff
PREFETCH window: d4000000-d7ffffff
PCI: Bus 7, cardbus bridge: 0000:06:04.0
IO window: 00007000-00007fff
IO window: 00008000-00008fff
PREFETCH window: 40000000-41ffffff
MEM window: 42000000-43ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 6000-6fff
MEM window: c4000000-c40fffff
PREFETCH window: 40000000-41ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 16 (level, low) -> IRQ 16
Simple Boot Flag at 0x36 set to 0x1
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SGI XFS with ACLs, security attributes, realtime, large block numbers, no
debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
vesafb: (C) 1988-2005, ATI Technologies Inc. , M26P, 01.00 (OEM: ATI
ATOMBIOS)
vesafb: VBE version: 3.0
vesafb: protected mode interface info at c000:af9a
vesafb: pmi: set display start = c00cb028, set palette = c00cb068
vesafb: hardware supports DDC2 transfers
vesafb: monitor limits: vf = 59 Hz, hf = 55 kHz, clk = 96 MHz
vesafb: trying maximum allowed refresh rate
vesafb: using default BIOS refresh rate
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 80x30
vesafb: framebuffer at 0xc8000000, mapped to 0xf8880000, using 16384k, total
16384k
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 18
ACPI: PCI interrupt for device 0000:00:1e.3 disabled
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
input: AT Translated Set 2 keyboard on isa0060/serio0
hdc: DV-W28EAT, ATAPI CD/DVD-ROM drive
input: PS/2 Mouse on isa0060/serio4
input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 1419kB Cache
Uniform CD-ROM driver Revision: 3.20
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 3
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
Cannot allocate resource for EISA slot 7
Cannot allocate resource for EISA slot 8
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Freeing unused kernel memory: 212k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xb8000000
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 19, io base 0x00001800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 20, io base 0x00001820
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 21, io base 0x00001840
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1299 $ Ben Collins <bcollins at debian.org>
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 20 (level, low) -> IRQ 18
usb 4-1: new low speed USB device using uhci_hcd and address 2
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[c4004000-c40047ff]
Max Packet=[2048]
sbp2: $Rev: 1306 $ Ben Collins <bcollins at debian.org>
libata version 1.12 loaded.
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on
usb-0000:00:1d.2-1
input: PS/2 Mouse on isa0060/serio4
input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
ahci version 1.01
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 20
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ahci: probe of 0000:00:1f.2 failed with error -12
ata_piix version 1.04
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 20
ata: 0x170 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x18F0 irq 14
ata1: dev 0 cfg 49:0f00 82:746b 83:7fe9 84:6023 85:f469 86:3d49 87:6023
88:203f
ata1: dev 0 ATA, max UDMA/100, 155910825 sectors: lba48
ata1(0): applying bridge limits
ata1: dev 0 configured for UDMA/100
scsi0 : ata_piix
Vendor: ATA Model: HTS541080G9AT00 Rev: MB4O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 155910825 512-byte hdwr sectors (79826 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 155910825 512-byte hdwr sectors (79826 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel at redhat.com
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f5776405376]
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
Adding 1020088k swap on /dev/sda5. Priority:-1 extents:1
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Power Button (CM) [PWRB]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 22
eth0: RealTek RTL8139 at 0xf9aa6800, 00:0f:b0:90:7a:95, IRQ 22
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, 1.0.3
ieee80211: Copyright (C) 2004-2005 Intel Corporation
<jketreno at linux.intel.com>
ipw2200: no version for "ieee80211_wx_get_encodeext" found: kernel tainted.
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.6
ipw2200: Copyright(c) 2003-2004 Intel Corporation
ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 22 (level, low) -> IRQ 23
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg,
GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 927 MBytes.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[fglrx] module loaded - fglrx 8.16.20 [Aug 16 2005] on minor 0
EXT2-fs warning (device sda1): ext2_fill_super: mounting ext3 filesystem as
ext2
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1e.2 to 64
intel8x0_measure_ac97_clock: measured 87481 usecs
intel8x0: clocking to 48000
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 16 (level, low) -> IRQ 16
Yenta: CardBus bridge found at 0000:06:04.0 [1179:ff01]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:04.0, mfunc 0x89501212, devctl 0x44
Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
cs: IO port probe 0x6000-0x6fff: clean.
pcmcia: parent PCI bridge Memory window: 0xc4000000 - 0xc40fffff
pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x41ffffff
Real Time Clock Driver v1.12
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1e.3 to
64
ALSA
/var/tmp/portage/alsa-driver-1.0.9b/work/alsa-driver-1.0.9b/pci/ac97/../../alsa-kernel/pci/ac97/ac97_codec.c:1993:
MC'97 1 converters and GPIO not ready (0xf00f)
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
NFSD: starting 90-second grace period
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
/dev/vmmon[14138]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[14138]: Module vmmon: initialized
/dev/vmnet: open called by PID 14241 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: enabling the bridge
bridge-eth0: up
bridge-eth0: already up
bridge-eth0: attached
/dev/vmnet: open called by PID 14267 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
[fglrx] free PCIe = 51118080
[fglrx] max PCIe = 51118080
[fglrx] free LFB = 120107008
[fglrx] max LFB = 120107008
[fglrx] free Inv = 0
[fglrx] max Inv = 0
[fglrx] total Inv = 0
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total PCIe = 16384
/dev/vmnet: open called by PID 14974 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 14975 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 15023 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 15022 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
The cardmgr hang during startup and lock the system
> --- Ursprüngliche Nachricht ---
> Von: Dominik Brodowski <linux at dominikbrodowski.net>
> An: Mario Fetka <mario-fetka at gmx.at>
> Kopie: linux-pcmcia at lists.infradead.org
> Betreff: Re: card manager hangs
> Datum: Thu, 22 Sep 2005 11:30:37 +0200
>
> Hi,
>
> Please send a full "dmesg" output. Does "cardmgr" hang during startup,
> locking the system up; or does it hang after you insert a card?
>
> Thanks,
> Dominik
>
> _______________________________________________
> Linux PCMCIA reimplementation list
> http://lists.infradead.org/mailman/listinfo/linux-pcmcia
>
--
Lust, ein paar Euro nebenbei zu verdienen? Ohne Kosten, ohne Risiko!
Satte Provisionen für GMX Partner: http://www.gmx.net/de/go/partner
--
GMX DSL = Maximale Leistung zum minimalen Preis!
2000 MB nur 2,99, Flatrate ab 4,99 Euro/Monat: http://www.gmx.net/de/go/dsl
More information about the linux-pcmcia
mailing list