Averatec 6240 pcmcia_socket0: unable to apply power

[James]

hi

please send full dmesg and lspci -vvv. most probably a
problem with the
BIOS not telling the kernel the truth about
used/reserved memory...

rgds
-daniel

Delete 

Here you go

Linux version 2.6.12-1.1447_FC4
(bhcompile at decompose.build.redhat.com) (gcc version
4.0.1 20050727 (Red Hat 4.0.1-5)) #1 Fri Aug 26
20:29:51 EDT 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00
(usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000
(reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000
(reserved)
 BIOS-e820: 0000000000100000 - 000000001dfd0000
(usable)
 BIOS-e820: 000000001dfd0000 - 000000001dfdf000 (ACPI
data)
 BIOS-e820: 000000001dfdf000 - 000000001e000000 (ACPI
NVS)
 BIOS-e820: 00000000ff780000 - 0000000100000000
(reserved)
0MB HIGHMEM available.
479MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 122832
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 118736 pages, LIFO batch:31
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 MSI                                  
) @ 0x000f7220
ACPI: RSDT (v001 MSI    1011     0x12062004 MSFT
0x00000097) @ 0x1dfd0000
ACPI: FADT (v002 MSI    1011     0x12062004 MSFT
0x00000097) @ 0x1dfd0200
ACPI: MADT (v001 MSI    OEMAPIC  0x12062004 MSFT
0x00000097) @ 0x1dfd0390
ACPI: OEMB (v001 MSI    AMI_OEM  0x12062004 MSFT
0x00000097) @ 0x1dfdf040
ACPI: DSDT (v001    MSI     1011 0x12062004 INTL
0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
Allocating PCI resources starting at 1e000000 (gap:
1e000000:e1780000)
Built 1 zonelists
Kernel command line: ro root=/dev/VolGroup00/LogVol00
rhgb quiet
Initializing CPU#0
CPU 0 irqstacks, hard=c0458000 soft=c0457000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 2000.451 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6,
262144 bytes)
Inode-cache hash table entries: 32768 (order: 5,
131072 bytes)
Memory: 480936k/491328k available (2518k kernel code,
9720k reserved, 690k data, 184k init, 0k highmem)
Checking if this processor honours the WP bit even in
supervisor mode... Ok.
Calibrating delay loop... 3973.12 BogoMIPS
(lpj=1986560)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary
module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff
00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 078bfbff e3d3fbff
00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bf3ff e3d3fbff 00000000
00000010 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Mobile AMD Athlon(tm) 64 Processor 3000+
stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0cb0)
checking if image is initramfs... it is
Freeing initrd memory: 1666k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last
bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050729
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
Uncovering SIS963 that hid as a SIS503 (compatible=0)
Enabling SiS 96x SMBus.
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table
[\_SB_.PCI0.P0P1._PRT]
ACPI: Embedded Controller [EC] (gpe 26)
ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 6 7 10 11 12
14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 6 7 10 11 12
14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 6 7 10 *11
12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *4 5 6 7 10 11
12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 6 *7 10 11
12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 *5 6 7 10 11
12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 6 7 10 11 12
14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 7 *10 11
12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 8 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If
it helps, post a report
apm: BIOS version 1.2 Flags 0x03 (Driver version
1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1126130714.806:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 1C1942C715575330
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1])
ACPI: Thermal Zone [THRM] (52 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected SiS 760 chipset
agpgart: AGP aperture is 4M @ 0xe0000000
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at
0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev
1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports,
IRQ sharing enabled
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:02.6[C] -> Link [LNKC] ->
GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt for device 0000:00:02.6 disabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K
size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision:
7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings:
hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings:
hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: IC25N080ATMR04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: Slimtype DVDRW SOSW-852S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 156301488 sectors (80026 MB) w/7884KiB Cache,
CHS=16383/255/63, UDMA(33)
hda: cache flushes supported
 hda: hda1 hda2 < hda5 hda6 hda7 >
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB
Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core
driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 32Kbytes
TCP established hash table entries: 16384 (order: 5,
131072 bytes)
TCP bind hash table entries: 16384 (order: 6, 458752
bytes)
TCP: Hash tables configured (established 16384 bind
16384)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
AC97 MC97 CBC0  MAC
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 184k freed
device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
dm-devel at redhat.com
input: AT Translated Set 2 keyboard on isa0060/serio0
alps.c: Enabling hardware tapping
input: PS/2 Mouse on isa0060/serio1
input: AlpsPS/2 ALPS GlidePoint on isa0060/serio1
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security:  3 users, 6 roles, 764 types, 87 bools
security:  55 classes, 180131 rules
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses
transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs),
uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not
configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs),
not configured for labeling
SELinux: initialized (dev devpts, type devpts), uses
transition SIDs
SELinux: initialized (dev eventpollfs, type
eventpollfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses
transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses
genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses
task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses
task SIDs
SELinux: initialized (dev proc, type proc), uses
genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses
genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses
genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses
genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses
genfs_contexts
floppy0: no floppy controllers found
sis900.c: v1.08.08 Jan. 22 2005
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 4
PCI: setting IRQ 4 as level-triggered
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKD] ->
GSI 4 (level, low) -> IRQ 4
0000:00:04.0: Realtek RTL8201 PHY transceiver found at
address 1.
0000:00:04.0: Using transceiver found at address 1 as
default
eth0: SiS 900 PCI Fast Ethernet at 0xd800, IRQ 4,
00:0c:76:f8:14:14.
snd_intel8x0: Unknown parameter `'
ACPI: PCI Interrupt 0000:00:02.7[C] -> Link [LNKC] ->
GSI 11 (level, low) -> IRQ 11
intel8x0_measure_ac97_clock: measured 49498 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:02.6[C] -> Link [LNKC] ->
GSI 11 (level, low) -> IRQ 11
i2c-sis96x version 1.0.0
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address:
0x0c00
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver
version: 0.4
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:03.3[D] -> Link [LNKH] ->
GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered,
assigned bus number 1
ehci_hcd 0000:00:03.3: irq 10, io mem 0xdffff000
PCI: cache line size of 64 is not supported by device
0000:00:03.3
ehci_hcd 0000:00:03.3: USB 2.0 initialized, EHCI 1.00,
driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller
(OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKE] ->
GSI 7 (level, low) -> IRQ 7
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered,
assigned bus number 2
ohci_hcd 0000:00:03.0: irq 7, io mem 0xdfffd000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:03.1[B] -> Link [LNKF] ->
GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered,
assigned bus number 3
ohci_hcd 0000:00:03.1: irq 5, io mem 0xdfffe000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] ->
GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:0a.0
[1462:0111]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x00001002,
devctl 0x44
Yenta TI: socket 0000:00:0a.0 probing PCI interrupt
failed, trying to fix
Yenta TI: socket 0000:00:0a.0 no PCI interrupts. Fish.
Please report.
Yenta: ISA IRQ mask 0x0000, PCI irq 0
Socket status: 00000720
cs: pcmcia_socket0: unable to apply power.
SELinux: initialized (dev ramfs, type ramfs), uses
genfs_contexts
cs: pcmcia_socket0: unable to apply power.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03e6a20(lo)
cs: pcmcia_socket0: unable to apply power.
IPv6 over IPv4 tunneling driver
ACPI: AC Adapter [ADP1] (on-line)
Using generic hotkey driver
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: Using generic hotkey driver
toshiba_acpi: Using generic hotkey driver
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
audit(1126155941.025:2): avc:  denied  { write } for 
pid=1413 comm="fsck" name="rhgb-console" dev=ramfs
ino=5123 scontext=system_u:system_r:fsadm_t
tcontext=system_u:object_r:ramfs_t tclass=fifo_file
EXT3 FS on dm-0, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda6, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses
transition SIDs
NTFS driver 2.1.22 [Flags: R/W MODULE].
NTFS-fs error (device hda1): parse_options():
Unrecognized mount option owner.ro.umask.
Adding 917496k swap on /dev/VolGroup00/LogVol01. 
Priority:-1 extents:1
SELinux: initialized (dev binfmt_misc, type
binfmt_misc), uses genfs_contexts
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x800-0x8ff: excluding 0x818-0x84f
0x858-0x89f
cs: IO port probe 0x100-0x4ff: excluding 0x480-0x48f
0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
eth0: Media Link On 100mbps full-duplex
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
SELinux: initialized (dev rpc_pipefs, type
rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager
initialized
Bluetooth: HCI socket layer initialized
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
Bluetooth: L2CAP ver 2.7
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.5
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
NTFS-fs error (device hda1): parse_options():
Unrecognized mount option owner.ro.umask.
SELinux: initialized (dev autofs, type autofs), uses
genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses
genfs_contexts
lp: driver loaded but no devices found
eth0: no IPv6 routers present
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: time out after reset.
PCMCIA: socket dcd4f844: *** DANGER *** unable to
remove socket power
cs: pcmcia_socket0: unable to apply power.
cs: pcmcia_socket0: unable to apply power.
cs: pcmcia_socket0: unable to apply power.
cs: pcmcia_socket0: unable to apply power.
cs: pcmcia_socket0: unable to apply power.
cs: pcmcia_socket0: unable to apply power.
cs: pcmcia_socket0: unable to apply power.
NTFS-fs error (device hda1): parse_options():
Unrecognized mount option owner.ro.umask.
cs: pcmcia_socket0: unable to apply power.
cs: pcmcia_socket0: unable to apply power.
cs: pcmcia_socket0: unable to apply power.
cs: pcmcia_socket0: unable to apply power.
application mixer_applet2 uses obsolete OSS audio
interface


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com