Sudden PCMCIA problems
John Smith
mimsyboro at gmail.com
Tue Oct 11 12:58:45 EDT 2005
Hello,
I have a Linksys WPC54G and have been using it with my laptop for
quite some time. I have two different installations of Linux and one
of Windows.
Suddenly last week the card stopped working under Linux although it
continues to work normally under Windows.
cardctl info doesn´t even recognize the card and returns that
everything is empty.
My dmesg:
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffe0000 (usable)
BIOS-e820: 000000001ffe0000 - 000000001ffeec00 (ACPI data)
BIOS-e820: 000000001ffeec00 - 000000001fff0000 (ACPI NVS)
BIOS-e820: 000000001fff0000 - 000000001fff4000 (reserved)
BIOS-e820: 000000001fff4000 - 0000000020000000 (usable)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
512MB LOWMEM available.
On node 0 totalpages: 131072
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126976 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f6eb0
ACPI: RSDT (v001 PTLTD RSDT 0x06041090 LTP 0x00000000) @ 0x1ffe4b71
ACPI: FADT (v001 IBM TP-16 0x06041090 0x00000000) @ 0x1ffeeb65
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06041090 LTP 0x00000001) @ 0x1ffeebd9
ACPI: DSDT (v001 IBM TP-16 0x06041090 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Built 1 zonelists
Kernel command line: root=/dev/hda8 ro quiet splash
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01406000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 995.815 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 511644k/524288k available (1436k kernel code, 11896k reserved,
754k data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1974.27 BogoMIPS (lpj=987136)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000
00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040
00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Looking for DSDT in initrd... not found!
ACPI: setting ELCR to 0200 (from 0800)
checking if image is initramfs...it isn't (bad gzip magic numbers);
looks like an initrd
Freeing initrd memory: 4300k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: Power Resource [PSER] (off)
ACPI: Power Resource [PSIO] (on)
ACPI: Embedded Controller [EC] (gpe 9)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas at hp.com
** so I can fix the driver.
pnp: 00:01: ioport range 0x1000-0x103f could not be reserved
pnp: 00:01: ioport range 0x1040-0x104f has been reserved
pnp: 00:01: ioport range 0xfe00-0xfe0f has been reserved
pnp: 00:08: ioport range 0x15e0-0x15ef has been reserved
Simple Boot Flag at 0x35 set to 0x1
audit: initializing netlink socket (disabled)
audit(1129060095.609:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:03.1[A] -> GSI 11 (level, low) -> IRQ 11
pnp: Device 00:0b activated.
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 1
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
LID SLPB PCI0 USB UART
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4300KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU] (supports 8 throttling states)
ACPI: Thermal Zone [THM0] (41 C)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1850-0x1857, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1858-0x185f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: HTS726060M9AT00, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 117210240 sectors (60011 MB) w/7877KiB Cache, CHS=16383/255/63, UDMA(33)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 >
Probing IDE interface ide1...
hdc: UJDA720 DVD/CDRW, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
Stopping tasks: ==|
Freeing memory... done (459 pages freed)
Restarting tasks... done
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 778640k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda8, internal journal
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
parport: PnPBIOS parport detected.
parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
input: PS/2 Generic Mouse on isa0060/serio1
ts: Compaq touchscreen protocol output
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel at redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
input: PC Speaker
Real Time Clock Driver v1.12
inserting floppy driver for 2.6.10-5-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
irda_init()
NET: Registered protocol family 23
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 440BX Chipset.
agpgart: Maximum main memory to use for agp memory: 440M
agpgart: AGP aperture is 64M @ 0xf8000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:02.0 [1014:0130]
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.0, mfunc 0x00001000, devctl 0x66
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000020
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:02.1 [1014:0130]
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.1, mfunc 0x00001000, devctl 0x66
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
e100: Intel(R) PRO/100 Network Driver, 3.2.3-k2-NAPI
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 11 (level, low) -> IRQ 11
e100: eth0: e100_probe: addr 0xe8120000, irq 11, MAC addr 00:03:47:91:79:F7
ACPI: PCI interrupt 0000:00:05.0[A] -> GSI 11 (level, low) -> IRQ 11
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: Intel Corp. 82371AB/EB/MB PIIX4 USB
uhci_hcd 0000:00:07.2: irq 11, io base 0x1860
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
piix4_smbus 0000:00:07.3: IBM Laptop detected; this module may corrupt
your serial eeprom! Refusing to load module!
piix4_smbus: probe of 0000:00:07.3 failed with error -1
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: IBM ThinkPad ACPI Extras v0.8
ibm_acpi: http://ibm-acpi.sf.net/
ibm_acpi: dock device not present
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f0500(lo)
IPv6 over IPv4 tunneling driver
cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
cs: warning: no high memory space available!
ndiswrapper version 1.1 loaded (preempt=yes,smp=no)
ndiswrapper: driver bcmwl5 (Linksys,02/19/2004, 3.50.21.11) loaded
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:02:00.0 to 64
ndiswrapper: using irq 11
wlan0: ndiswrapper ethernet device 00:06:25:3e:4b:79 using driver
bcmwl5, configuration file 14E4:4320.5.conf
wlan0: encryption modes supported: WEP, WPA with TKIP, WPA with AES/CCMP
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 17
smbfs: Unrecognized mount option noexec
eth0: no IPv6 routers present
My lspci -vvv:
0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: <available only to root>
0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP
bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f0000000-f7ffffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
0000:00:02.0 CardBus bridge: Texas Instruments PCI1450 (rev 03)
Subsystem: IBM: Unknown device 0130
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x20 (128 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 50000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 20000000-203ff000 (prefetchable)
Memory window 1: 20400000-207ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:00:02.1 CardBus bridge: Texas Instruments PCI1450 (rev 03)
Subsystem: IBM: Unknown device 0130
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x20 (128 bytes)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 50100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 20800000-20bff000 (prefetchable)
Memory window 1: 20c00000-20fff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:03.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro
100] (rev 0c)
Subsystem: Intel Corp. EtherExpress PRO/100 SP Mobile Combo Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e8120000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 1800 [size=64]
Region 2: Memory at e8100000 (32-bit, non-prefetchable) [size=128K]
Capabilities: <available only to root>
0000:00:03.1 Serial controller: Lucent Microelectronics LT WinModem
(rev 01) (prog-if 00 [8250])
Subsystem: Intel Corp.: Unknown device 2205
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1840 [size=8]
Region 1: Memory at e8121000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
0000:00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24
[CrystalClear SoundFusion Audio Accelerator] (rev 01)
Subsystem: IBM: Unknown device 0153
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 6000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e8122000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
0000:00:07.0 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev
01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 1850 [size=16]
0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev
01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1860 [size=32]
0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
0000:01:00.0 VGA compatible controller: S3 Inc. 86C270-294
Savage/IX-MV (rev 13) (prog-if 00 [VGA])
Subsystem: IBM ThinkPad T20
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 63750ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=128M]
Capabilities: <available only to root>
0000:02:00.0 Network controller: Broadcom Corporation BCM4306
802.11b/g Wireless LAN Controller (rev 02)
Subsystem: Linksys WPC54G
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20400000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <available only to root>
Any help will be appreciated
More information about the linux-pcmcia
mailing list