TI CardBus bridge problem
Chris Lu
kalenedrael at yahoo.com
Mon Jul 4 03:37:10 EDT 2005
--- Russell King <rmk+pcmcia at arm.linux.org.uk> wrote:
> On Mon, Jul 04, 2005 at 12:02:26AM -0700, Chris Lu
> wrote:
> > > If this is the case, try passing
> "pci=assign-busses"
> >
> > I tried this with an unpatched kernel 2.6.12.2 and
> it
> > seems to freeze at the "Booting the kernel..."
> stage.
>
> Please send a full lspc -vvv dump.
>
(Sorry for the poor formatting)
-------------------------
0000:00:00.0 Host bridge: nVidia Corporation nForce3
Host Bridge (rev a4)
Control: I/O- Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at e8000000 (32-bit,
prefetchable) [size=128M]
Capabilities: [44] #08 [0180]
Capabilities: [c0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+
ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+
GART64- 64bit- FW- Rate=x4
0000:00:01.0 ISA bridge: nVidia Corporation nForce3
LPC Bridge (rev a6)
Subsystem: nVidia Corporation: Unknown device
0c80
Control: I/O+ Mem+ BusMaster+ SpecCycle+
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:01.1 SMBus: nVidia Corporation nForce3 SMBus
(rev a4)
Subsystem: Hewlett-Packard Company: Unknown
device 006d
Control: I/O+ Mem- BusMaster- SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 2040 [size=64]
Region 5: I/O ports at 2000 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2-
AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0
PME-
0000:00:02.0 USB Controller: nVidia Corporation
nForce3 USB 1.1 (rev a5) (prog-if 10 [OHCI])
Subsystem: nVidia Corporation: Unknown device
0c80
Control: I/O- Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at e0000000 (32-bit,
non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+
AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0
PME-
0000:00:02.1 USB Controller: nVidia Corporation
nForce3 USB 1.1 (rev a5) (prog-if 10 [OHCI])
Subsystem: nVidia Corporation: Unknown device
0c80
Control: I/O- Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at e0001000 (32-bit,
non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+
AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0
PME-
0000:00:02.2 USB Controller: nVidia Corporation
nForce3 USB 2.0 (rev a2) (prog-if 20 [EHCI])
Subsystem: nVidia Corporation: Unknown device
0c80
Control: I/O- Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at e0004000 (32-bit,
non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+
AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0
PME-
0000:00:06.0 Multimedia audio controller: nVidia
Corporation nForce3 Audio (rev a2)
Subsystem: Hewlett-Packard Company: Unknown
device 006d
Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 1400 [size=256]
Region 1: I/O ports at 1c00 [size=128]
Region 2: Memory at e0002000 (32-bit,
non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+
AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0
PME-
0000:00:06.1 Modem: nVidia Corporation: Unknown device
00d9 (rev a2) (prog-if 00 [Generic])
Subsystem: Hewlett-Packard Company: Unknown
device 006d
Control: I/O+ Mem+ BusMaster- SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 22
Region 0: I/O ports at 1800 [size=256]
Region 1: I/O ports at 1c80 [size=128]
Region 2: Memory at e0003000 (32-bit,
non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2-
AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0
PME-
0000:00:08.0 IDE interface: nVidia Corporation nForce3
IDE (rev a5) (prog-if 8a [Master SecP PriP])
Subsystem: nVidia Corporation: Unknown device
0c80
Control: I/O+ Mem- BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at 2080 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2-
AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0
PME-
0000:00:0a.0 PCI bridge: nVidia Corporation nForce3
PCI Bridge (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02,
sec-latency=128
I/O behind bridge: 00003000-00007fff
Memory behind bridge: e0100000-e17fffff
Prefetchable memory behind bridge:
fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort-
>Reset- FastB2B-
0000:00:0b.0 PCI bridge: nVidia Corporation nForce3
AGP Bridge (rev a4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Bus: primary=00, secondary=01, subordinate=01,
sec-latency=10
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e2000000-e2ffffff
Prefetchable memory behind bridge:
f0000000-f80fffff
BridgeCtl: Parity+ SERR+ NoISA+ VGA+ MAbort-
>Reset- FastB2B-
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD]
K8 NorthBridge
Control: I/O- Mem- BusMaster- SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] #08 [2101]
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD]
K8 NorthBridge
Control: I/O- Mem- BusMaster- SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD]
K8 NorthBridge
Control: I/O- Mem- BusMaster- SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD]
K8 NorthBridge
Control: I/O- Mem- BusMaster- SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
0000:01:00.0 VGA compatible controller: nVidia
Corporation NV17 [GeForce4 440 Go 64M] (rev a3)
(prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company: Unknown
device 006d
Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at e2000000 (32-bit,
non-prefetchable) [size=16M]
Region 1: Memory at f0000000 (32-bit,
prefetchable) [size=128M]
Region 2: Memory at f8000000 (32-bit,
prefetchable) [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2-
AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0
PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA-
ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+
GART64- 64bit- FW- Rate=x4
0000:02:00.0 FireWire (IEEE 1394): Texas Instruments
TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
(prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company: Unknown
device 006d
Control: I/O- Mem+ BusMaster+ SpecCycle-
MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache
Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at e0108000 (32-bit,
non-prefetchable) [size=2K]
Region 1: Memory at e0100000 (32-bit,
non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+
AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0
PME+
0000:02:01.0 Ethernet controller: Realtek
Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd.
RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 7000 [size=256]
Region 1: Memory at e0108800 (32-bit,
non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+
AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0
PME-
0000:02:02.0 Network controller: Broadcom Corporation
BCM4306 802.11b/g Wireless LAN Controller (rev 03)
Subsystem: Hewlett-Packard Company: Unknown
device 12f8
Control: I/O- Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e0104000 (32-bit,
non-prefetchable) [size=8K]
0000:02:04.0 CardBus bridge: Texas Instruments:
Unknown device ac54 (rev 01)
Subsystem: Hewlett-Packard Company: Unknown
device 006d
Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at e0106000 (32-bit,
non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06,
sec-latency=176
Memory window 0: e0200000-e03ff000
(prefetchable)
Memory window 1: e0400000-e05ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort-
>Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:02:04.1 CardBus bridge: Texas Instruments:
Unknown device ac54 (rev 01)
Subsystem: Hewlett-Packard Company: Unknown
device 006d
Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin B routed to IRQ 16
Region 0: Memory at e0107000 (32-bit,
non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a,
sec-latency=176
Memory window 0: e1000000-e13ff000
(prefetchable)
Memory window 1: e0c00000-e0fff000
I/O window 0: 00006000-00006fff
I/O window 1: 00005000-00005fff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort-
>Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:02:04.2 System peripheral: Texas Instruments:
Unknown device 8201 (rev 01)
Subsystem: Hewlett-Packard Company: Unknown
device 006d
Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1750ns min, 1000ns max), Cache
Line Size: 0x10 (64 bytes)
Region 0: I/O ports at 7400 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2-
AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0
PME-
--------------------------
Chris Lu
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
More information about the linux-pcmcia
mailing list