pd6729 infinite eventloop
Bill O'Donnell
billodo at visi.com
Fri Feb 18 23:12:41 EST 2005
I've reflashed the board with a new BIOS and the ACPI problem seems
to have gone away, but the "pd6729: infinite eventloop" still happens
when
I insert the pcmcia card, with a curious new line interspersed between
each of the eventloop messages, namely "IRQ 7".
I'm attaching the new dmesg and lspci -v outputs.
-Bill
------------------------------------
-------------- next part --------------
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1eee8507
ACPI: FADT (v001 KOM_KF CP306 0x06040000 PTL 0x00000050) @ 0x1eeeaf32
ACPI: DSDT (v001 KOM_KF CP306 0x06040000 MSFT 0x0100000e) @ 0x00000000
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (013e3000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1600.448 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 495356k/506752k available (2795k kernel code, 10724k reserved, 997k data, 180k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3162.11 BogoMIPS (lpj=1581056)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000
CPU: After vendor identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00000040 00000180 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Mobile Genuine Intel(R) processor 1600MHz stepping 05
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0ca0)
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 2116k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd9a4, last bus=4
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 6 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas at hp.com
** so I can fix the driver.
pnp: 00:03: ioport range 0x800-0x80f has been reserved
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1 C2)
ACPI: Processor [CPU0] (supports 8 throttling states)
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
hw_random hardware driver 1.0.0 loaded
i8042.c: Can't read CTR while initializing i8042.
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
elevator: using anticipatory as default io scheduler
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 7 (level, low) -> IRQ 7
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2000-0x2007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x2008-0x200f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: SanDisk SDCFB-4096, CFA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 8005536 sectors (4098 MB) w/1KiB Cache, CHS=7942/16/63, DMA
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0:<4>hda: dma_timer_expiry: dma status == 0x21
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
p1
st: Version 20041025, fixed bufsize 32768, s/g segs 256
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
speedstep-centrino: obtaining ACPI data failed
speedstep-centrino: no support for CPU model "Mobile Genuine Intel(R) processor 1600MHz": send /proc/cpuinfo to Jeremy Fitzhardinge <jeremy at goop.org>
p4-clockmod: Warning: Pentium M detected. The speedstep_centrino module offers voltage scaling in addition of frequency scaling. You should use that instead of p4-clockmod, if possible.
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
ACPI wakeup devices:
PWRB USB0 USB1 USB2 USB7
ACPI: (supports S0 S1 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 2116KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 180k freed
/dev/ide/host0/bus0/target0/lun0:<4>hda: dma_timer_expiry: dma status == 0x21
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
p1
hda: dma_timer_expiry: dma status == 0x21
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: dma_timer_expiry: dma status == 0x21
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
ext3: No journal on filesystem on hda1
/dev/ide/host0/bus0/target0/lun0: p1
/dev/ide/host0/bus0/target0/lun0: p1
/dev/ide/host0/bus0/target0/lun0: p1
/dev/ide/host0/bus0/target0/lun0: p1
ext3: No journal on filesystem on hda1
/dev/ide/host0/bus0/target0/lun0: p1
/dev/ide/host0/bus0/target0/lun0: p1
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Intel ISA PCIC probe: not found.
Device 'i823650' does not have a release() function, it is broken and must be fixed.
Badness in device_release at drivers/base/core.c:85
[<c0292043>] kobject_cleanup+0x83/0x90
[<c0292050>] kobject_release+0x0/0x10
[<c02929a3>] kref_put+0x33/0x80
[<c0292076>] kobject_put+0x16/0x20
[<c0292050>] kobject_release+0x0/0x10
[<df8822af>] init_i82365+0x18f/0x1a6 [i82365]
[<c012f942>] sys_init_module+0x112/0x1a0
[<c0102d17>] syscall_call+0x7/0xb
e100: Intel(R) PRO/100 Network Driver, 3.2.3-k2-NAPI
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 10 (level, low) -> IRQ 10
e100: eth0: e100_probe: addr 0xd0120000, irq 10, MAC addr 00:80:82:49:08:60
Intel(R) PRO/1000 Network Driver - version 5.5.4-k2
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:02:0d.0[A] -> GSI 11 (level, low) -> IRQ 11
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 5, io base 0x1880
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 11, io base 0x1c00
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 7 (level, low) -> IRQ 7
uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 7, io base 0x1c80
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-2: new full speed USB device using uhci_hcd and address 2
hub 2-2:1.0: USB hub found
hub 2-2:1.0: 3 ports detected
usb 3-2: new full speed USB device using uhci_hcd and address 2
Initializing USB Mass Storage driver...
usb 2-2.1: new full speed USB device using uhci_hcd and address 3
usb 2-2.3: new low speed USB device using uhci_hcd and address 4
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard Hub] on usb-0000:00:1d.1-2.1
input: USB HID v1.10 Device [Dell Dell USB Keyboard Hub] on usb-0000:00:1d.1-2.1
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.1-2.3
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 855 Chipset.
agpgart: Maximum main memory to use for agp memory: 423M
agpgart: Detected 16252K stolen memory.
agpgart: AGP aperture is 128M @ 0xd8000000
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 11, pci mem 0xd0080000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
drivers/usb/input/hid-core.c: input irq status -84 received
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
usb 4-6: new high speed USB device using ehci_hcd and address 3
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
scsi1 : SCSI emulation for USB Mass Storage devices
usb 3-2: USB disconnect, address 2
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
usb 2-2: USB disconnect, address 2
usb 2-2.1: USB disconnect, address 3
usb 2-2.3: USB disconnect, address 4
usb 2-2: new full speed USB device using uhci_hcd and address 5
hub 2-2:1.0: USB hub found
hub 2-2:1.0: 3 ports detected
usb 2-2.1: new full speed USB device using uhci_hcd and address 6
input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard Hub] on usb-0000:00:1d.1-2.1
input: USB HID v1.10 Device [Dell Dell USB Keyboard Hub] on usb-0000:00:1d.1-2.1
usb 2-2.3: new low speed USB device using uhci_hcd and address 7
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.1-2.3
ACPI: PCI interrupt 0000:04:04.0[A] -> GSI 7 (level, low) -> IRQ 7
pd6729: Cirrus PD6729 PCI to PCMCIA Bridge at 0x4000 on irq 7
pd6729: configured as a 2 socket device.
e100: eth0: e100_watchdog: link up, 10Mbps, half-duplex
Vendor: LITE-ON Model: LTR-52327S Rev: QS53
Type: CD-ROM ANSI SCSI revision: 00
sr0: scsi3-mmc drive: 52x/52x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 5
usb-storage: device scan complete
i82092: Unknown parameter `cycle_time'
cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x280-0x28f 0x370-0x377 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
-------------- next part --------------
0000:00:00.0 Host bridge: Intel Corp. 82852/855GM Host Bridge (rev 02)
Subsystem: Intel Corp.: Unknown device 1965
Flags: bus master, fast devsel, latency 0
Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [40] #09 [8105]
Capabilities: [a0] AGP version 2.0
0000:00:00.1 System peripheral: Intel Corp. 855GM/GME GMCH Memory I/O Control Registers (rev 02)
Subsystem: Intel Corp.: Unknown device 1965
Flags: bus master, fast devsel, latency 0
0000:00:00.3 System peripheral: Intel Corp. 855GM/GME GMCH Configuration Process Registers (rev 02)
Subsystem: Intel Corp.: Unknown device 1965
Flags: bus master, fast devsel, latency 0
0000:00:01.0 PCI bridge: Intel Corp. 855GME GMCH Host-to-AGP Bridge (Virtual PCI-to-PCI) (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, fast devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
0000:00:02.0 VGA compatible controller: Intel Corp. 82852/855GM Integrated Graphics Device (rev 02) (prog-if 00 [VGA])
Subsystem: Intel Corp.: Unknown device 1968
Flags: bus master, fast devsel, latency 0, IRQ 5
Memory at d8000000 (32-bit, prefetchable) [size=128M]
Memory at d0000000 (32-bit, non-prefetchable) [size=512K]
I/O ports at 1800 [size=8]
Capabilities: [d0] Power Management version 1
0000:00:1d.0 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corp.: Unknown device 1965
Flags: bus master, medium devsel, latency 0, IRQ 5
I/O ports at 1880 [size=32]
0000:00:1d.1 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corp.: Unknown device 1965
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 1c00 [size=32]
0000:00:1d.2 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corp.: Unknown device 1965
Flags: bus master, medium devsel, latency 0, IRQ 7
I/O ports at 1c80 [size=32]
0000:00:1d.7 USB Controller: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corp.: Unknown device 1965
Flags: bus master, medium devsel, latency 0, IRQ 11
Memory at d0080000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] #0a [2080]
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 82) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=04, sec-latency=64
I/O behind bridge: 00003000-00004fff
Memory behind bridge: d0100000-d01fffff
0000:00:1f.0 ISA bridge: Intel Corp. 82801DB/DBL (ICH4/ICH4-L) LPC Bridge (rev 02)
Flags: bus master, medium devsel, latency 0
0000:00:1f.1 IDE interface: Intel Corp. 82801DB/DBL (ICH4/ICH4-L) UltraATA-100 IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corp.: Unknown device 1965
Flags: bus master, medium devsel, latency 0, IRQ 7
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at 2000 [size=16]
Memory at 20000000 (32-bit, non-prefetchable) [size=1K]
0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 02)
Subsystem: Intel Corp.: Unknown device 1965
Flags: medium devsel, IRQ 10
I/O ports at 2080 [size=32]
0000:02:08.0 Ethernet controller: Intel Corp. 82801BD PRO/100 VE (CNR) Ethernet Controller (rev 82)
Subsystem: Intel Corp. 82801BD PRO/100 VE (CNR) Ethernet Controller
Flags: bus master, medium devsel, latency 66, IRQ 10
Memory at d0120000 (32-bit, non-prefetchable) [size=4K]
I/O ports at 3000 [size=64]
Capabilities: [dc] Power Management version 2
0000:02:0c.0 PCI bridge: Texas Instruments PCI2050 PCI-to-PCI Bridge (prog-if 00 [Normal decode])
Flags: bus master, medium devsel, latency 64
Bus: primary=02, secondary=03, subordinate=04, sec-latency=68
I/O behind bridge: 00004000-00004fff
Capabilities: [dc] Power Management version 1
0000:02:0d.0 Ethernet controller: Intel Corp. 82540EM Gigabit Ethernet Controller (rev 02)
Subsystem: Intel Corp. 82540EM Gigabit Ethernet Controller
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11
Memory at d0100000 (32-bit, non-prefetchable) [size=128K]
I/O ports at 3080 [size=64]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device.
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
0000:03:0e.0 PCI bridge: Digital Equipment Corporation DECchip 21154 (rev 05) (prog-if 00 [Normal decode])
Flags: bus master, fast Back2Back, 66MHz, medium devsel, latency 64
Bus: primary=03, secondary=04, subordinate=04, sec-latency=68
I/O behind bridge: 00004000-00004fff
Capabilities: [dc] Power Management version 1
0000:04:04.0 PCMCIA bridge: Cirrus Logic CL 6729 (rev 07)
Flags: stepping, slow devsel, IRQ 7
I/O ports at 4000 [size=4]
More information about the linux-pcmcia
mailing list