Problem with PCMCIA ENE CB1410 controler (yenta probing IRG and
memory hole)
frederic
kakou9 at free.fr
Sat Apr 30 08:25:07 EDT 2005
Hello,
I've some troubles with my pcmcia ENE CB1410 controler (TARGA 820
sepron 2600+)
I'm trying to install a mandriva 10.2 with a 2.6.11 kernel
but the pcmcia controller has two problems :
- Yenta probing IRQ
- Bios memory hole, perhaps after reading your article about the
**** DANGER message
I send you the dmesg , iomem , ... but I 've some problems to
compile the cbdump.c (pci.h.......)
Can you help me please.
Frédéric WOJTCZAK (French User)
-------------- next part --------------
Linux version 2.6.11-6mdk (gb at n2.mandrakesoft.com) (gcc version 3.4.3 (Mandrakelinux 10.2 3.4.3-3mdk)) #1 Tue Mar 22 16:04:32 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dfd0000 (usable)
BIOS-e820: 000000001dfd0000 - 000000001dfde000 (ACPI data)
BIOS-e820: 000000001dfde000 - 000000001e000000 (ACPI NVS)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
479MB LOWMEM available.
found SMP MP-table at 000ff780
NX (Execute Disable) protection: active
On node 0 totalpages: 122832
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 118736 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f7440
ACPI: RSDT (v001 Arima 161Fh 0x02000515 MSFT 0x00000097) @ 0x1dfd0000
ACPI: FADT (v002 Arima 161Fh 0x02000515 MSFT 0x00000097) @ 0x1dfd0200
ACPI: MADT (v001 Arima 161Fh 0x02000515 MSFT 0x00000097) @ 0x1dfd0390
ACPI: OEMB (v001 Arima 161Fh 0x02000515 MSFT 0x00000097) @ 0x1dfde040
ACPI: DSDT (v001 Arima 161Fh 0x00000024 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 1e000000 (gap: 1e000000:e1780000)
Built 1 zonelists
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
Kernel command line: BOOT_IMAGE=linux ro root=306 resume=/dev/hda5 splash=silent
bootsplash: silent mode.
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1597.067 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 482616k/491328k available (2295k kernel code, 8152k reserved, 686k data, 264k init, 0k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3170.30 BogoMIPS (lpj=1585152)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000000 00000000 00000001
CPU: After vendor identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000000 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 128K (64 bytes/line)
CPU: After all inits, caps: 078bfbff c3d3fbff 00000000 00000010 00000000 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Mobile AMD Sempron(tm) Processor 2600+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: Looking for DSDT in initrd... not found.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 218k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Uncovering SIS963 that hid as a SIS503 (compatible=0)
Enabling SiS 96x SMBus.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 25)
ACPI: PCI Interrupt Link [LNKA] (IRQs 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 7 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas at hp.com
** so I can fix the driver.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1114869883.210:0): initialized
inotify device minor=63
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
vesafb: framebuffer at 0xd0000000, mapped to 0xde880000, using 3750k, total 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=7
vesafb: protected mode interface info at cbe4:0008
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 35024 bytes,<6>...found (800x600, 34976 bytes, v3).
Console: switching to colour frame buffer device 92x32
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ACPI: PCI interrupt 0000:00:02.6[C] -> GSI 18 (level, low) -> IRQ 18
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe at suse.de) and petero2 at telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: SAMSUNG MP0402H, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: PIONEER DVD-RW DVR-K15, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 78242976 sectors (40060 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
Synaptics Touchpad, model: 1
Firmware: 5.9
Sensor: 35
new absolute packet format
Touchpad has extended capability bits
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 1
ACPI wakeup devices:
PCI0 MAC MC97 LID0
ACPI: (supports S0 S1 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
devfs_mk_dev: could not append to parent for md/0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 264k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 20
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: irq 20, pci mem 0xdffff000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: irq 21, pci mem 0xdfffe000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usb 1-2: new full speed USB device using ohci_hcd and address 2
ACPI: PCI interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: irq 23, pci mem 0xdfffd000
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 3
PCI: cache line size of 64 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
usb 1-2: USB disconnect, address 2
usb 3-3: new high speed USB device using ehci_hcd and address 2
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
EXT3 FS on hda6, internal journal
Vendor: VBTM Model: Store 'n' Go Rev: 4.90
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
SCSI device sda: 1005312 512-byte hdwr sectors (515 MB)
sda: Write Protect is off
sda: Mode Sense: 45 00 00 08
sda: assuming drive cache: write through
SCSI device sda: 1005312 512-byte hdwr sectors (515 MB)
sda: Write Protect is off
sda: Mode Sense: 45 00 00 08
sda: assuming drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Adding 1044184k swap on /dev/hda5. Priority:-1 extents:1
slamr: module license 'Smart Link Ltd.' taints kernel.
slamr: SmartLink AMRMO modem.
slamr: probe 1039:7013 SiS630 card...
ACPI: PCI interrupt 0000:00:02.6[C] -> GSI 18 (level, low) -> IRQ 18
slamr: mc97 codec is CXT23
slamr: slamr0 is SiS630 card.
Non-volatile memory driver v1.2
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected SiS 760 chipset
agpgart: Maximum main memory to use for agp memory: 409M
agpgart: AGP aperture is 4M @ 0xe0000000
loop: loaded (max 8 devices)
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins at debian.org>
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[dfff9800-dfff9fff] Max Packet=[2048]
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
sis900.c: v1.08.07 11/02/2003
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 19
0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xd800, IRQ 19, 00:03:25:1d:33:60.
eth1394: $Rev: 1224 $ Ben Collins <bcollins at debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
eth0: Media Link Off
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Thermal Zone [THRM] (35 C)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000325213800749b]
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
Yenta: CardBus bridge found at 0000:00:0a.0 [161f:2038]
Yenta: adjusting diagnostic: 40 -> 60
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x01001002, devctl 0x44
Yenta TI: socket 0000:00:0a.0 probing PCI interrupt failed, trying to fix
Yenta TI: socket 0000:00:0a.0 no PCI interrupts. Fish. Please report.
Yenta: ISA IRQ mask 0x0000, PCI irq 0
Socket status: 74177c38
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
floppy0: no floppy controllers found
floppy0: no floppy controllers found
NET: Registered protocol family 17
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 18
intel8x0_measure_ac97_clock: measured 49743 usecs
intel8x0: clocking to 48000
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.7
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.5
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03b26e0(lo)
IPv6 over IPv4 tunneling driver
Disabled Privacy Extensions on device dc786c00(sit0)
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09e)
powernow-k8: 0 : fid 0x0 (800 MHz), vid 0x13 (1075 mV)
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x8 (1350 mV)
cpu_init done, current fid 0x8, vid 0x8
PCMCIA: socket dd0d902c: *** DANGER *** unable to remove socket power
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 0 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 5 changed to on
eth0: no IPv6 routers present
-------------- next part --------------
CPU0
0: 277540 IO-APIC-edge timer
1: 479 IO-APIC-edge i8042
8: 1 IO-APIC-edge rtc
9: 43 IO-APIC-level acpi
12: 6933 IO-APIC-edge i8042
14: 6384 IO-APIC-edge ide0
15: 1990 IO-APIC-edge ide1
18: 3407 IO-APIC-level SiS630, ohci1394, SiS SI7012
19: 5 IO-APIC-level eth0
20: 12 IO-APIC-level ohci_hcd
21: 0 IO-APIC-level ohci_hcd
23: 1395 IO-APIC-level ehci_hcd
NMI: 0
LOC: 277487
ERR: 0
MIS: 0
-------------- next part --------------
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cbfff : Video ROM
000f0000-000fffff : System ROM
00100000-1dfcffff : System RAM
00100000-0033dcda : Kernel code
0033dcdb-003e96ff : Kernel data
1dfd0000-1dfddfff : ACPI Tables
1dfde000-1dffffff : ACPI Non-volatile Storage
1e000000-1e000fff : 0000:00:0a.0
1e000000-1e000fff : yenta_socket
1e400000-1e7fffff : PCI CardBus #02
1e800000-1ebfffff : PCI CardBus #02
cd500000-dd4fffff : PCI Bus #01
d0000000-d7ffffff : 0000:01:00.0
d0000000-d0ffffff : vesafb
df600000-df6fffff : PCI Bus #01
df6e0000-df6fffff : 0000:01:00.0
dfff9800-dfff9fff : 0000:00:0c.0
dfff9800-dfff9fff : ohci1394
dfffc000-dfffcfff : 0000:00:04.0
dfffc000-dfffcfff : sis900
dfffd000-dfffdfff : 0000:00:03.3
dfffd000-dfffdfff : ehci_hcd
dfffe000-dfffefff : 0000:00:03.1
dfffe000-dfffefff : ohci_hcd
dffff000-dfffffff : 0000:00:03.0
dffff000-dfffffff : ohci_hcd
e0000000-e3ffffff : 0000:00:00.0
ff780000-ffffffff : reserved
-------------- next part --------------
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
03c0-03df : vesafb
03f6-03f6 : ide0
0800-0803 : PM1a_EVT_BLK
0804-0805 : PM1a_CNT_BLK
0808-080b : PM_TMR
0810-0815 : ACPI CPU throttle
0816-0816 : PM2_CNT_BLK
0820-0823 : GPE0_BLK
0830-0833 : GPE1_BLK
0c00-0c1f : 0000:00:02.1
0cf8-0cff : PCI conf1
4000-40ff : PCI CardBus #02
4400-44ff : PCI CardBus #02
b000-bfff : PCI Bus #01
bc00-bc7f : 0000:01:00.0
d800-d8ff : 0000:00:04.0
d800-d8ff : sis900
dc00-dc7f : 0000:00:0c.0
e000-e07f : 0000:00:02.7
e000-e07f : SiS SI7012
e400-e4ff : 0000:00:02.7
e400-e4ff : SiS SI7012
e800-e8ff : 0000:00:02.6
e800-e8ff : SiS630
ec00-ec7f : 0000:00:02.6
ec00-ec7f : SiS630
ffa0-ffaf : 0000:00:02.5
ffa0-ffa7 : ide0
ffa8-ffaf : ide1
-------------- next part --------------
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 760/M760 Host (rev 03)
Subsystem: Rioworks: Unknown device 2038
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: <available only to root>
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SG86C202 (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: df600000-df6fffff
Prefetchable memory behind bridge: cd500000-dd4fffff
Secondary status: SERR
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS963 [MuTIOL Media IO] (rev 25)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 0c00 [size=32]
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (prog-if 80 [Master])
Subsystem: Rioworks: Unknown device 2038
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Region 4: I/O ports at ffa0 [size=16]
00:02.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev a0) (prog-if 00 [Generic])
Subsystem: Rioworks: Unknown device 2038
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at e800 [size=256]
Region 1: I/O ports at ec00 [size=128]
Capabilities: <available only to root>
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] Sound Controller (rev a0)
Subsystem: Rioworks: Unknown device 2038
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at e400 [size=256]
Region 1: I/O ports at e000 [size=128]
Capabilities: <available only to root>
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Rioworks: Unknown device 2038
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at dffff000 (32-bit, non-prefetchable) [size=4K]
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Rioworks: Unknown device 2038
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at dfffe000 (32-bit, non-prefetchable) [size=4K]
00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller (prog-if 20 [EHCI])
Subsystem: Rioworks: Unknown device 2038
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 23
Region 0: Memory at dfffd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 91)
Subsystem: Rioworks: Unknown device 2038
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (13000ns min, 2750ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at dfffc000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at dffc0000 [disabled] [size=128K]
Capabilities: <available only to root>
00:0a.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: Memory at 1e000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 1e400000-1e7ff000 (prefetchable)
Memory window 1: 1e800000-1ebff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
00:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), cache line size 10
Interrupt: pin A routed to IRQ 18
Region 0: Memory at dfff9800 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at dc00 [size=128]
Capabilities: <available only to root>
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: <available only to root>
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 661/741/760 PCI/AGP VGA Display Adapter (prog-if 00 [VGA])
Subsystem: Rioworks: Unknown device 2038
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
BIST result: 00
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at df6e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at bc00 [size=128]
Expansion ROM at <unassigned> [disabled]
Capabilities: <available only to root>
More information about the linux-pcmcia
mailing list