Cardbus cards not being seen?
Martin Glazer
sourceforge at glazer.ca
Wed Oct 13 23:19:16 EDT 2004
Hi All,
I need some help trying to figure out what is wrong with pcmcia on my laptop.
I have a Toshiba Satellite Pro 6100 (PS610C) running Gentoo linux with kernel
2.6.8 (just upgraded from 2.4.27). The laptop has a built in 802.11b card and
2 pcmcia slots. The built-in card is listed as a 16-bit PC Card.
The problem I am having is that the built-in card is recognized and working
but any cardbus cards are not recognized, in fact nothing shows up at all in
dmesg when one is inserted. If I insert an old 16-bit card, it is recognized.
I do not see any errors or warning in the dmesg output. I have also tried to
disable ACPI and various other settings (acpi=off pci=noacpi
pci=usepirqmask), but with no luck.
cardctl status gives this output when a cardbus card has been inserted
rover root # cardctl status
Socket 0:
3.3V 16-bit PC Card
function 0: [ready]
Socket 1:
no card
Socket 2:
3.3V CardBus card
function 0: [ready]
function 1: [ready]
I have tried with 2 different Cardbus cards, a 3Com 3CCFEM656 NIC/Modem and a
SMC2835W 802.11g wireless card (Prism GT/Prism Duette) - same result.
Any help/suggestions would be appreciated.
Thanks
The relevant parts of lspci -vv with the 3Com and SMC card inserted are:
0000:02:0a.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus
Controller (rev 01)
Subsystem: Lucent Technologies: Unknown device ab01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20001000 (32-bit, non-prefetchable)
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 20400000-207ff000 (prefetchable)
Memory window 1: 20800000-20bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:02:0b.0 CardBus bridge: Toshiba America Info Systems ToPIC95 PCI to
Cardbus Bridge with ZV Support (rev 32)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20002000 (32-bit, non-prefetchable)
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=0
Memory window 0: 20c00000-20fff000 (prefetchable)
Memory window 1: 21000000-213ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:02:0b.1 CardBus bridge: Toshiba America Info Systems ToPIC95 PCI to
Cardbus Bridge with ZV Support (rev 32)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 20003000 (32-bit, non-prefetchable)
Bus: primary=02, secondary=0b, subordinate=0e, sec-latency=0
Memory window 0: 21400000-217ff000 (prefetchable)
Memory window 1: 21800000-21bff000
I/O window 0: 00005000-000050ff
I/O window 1: 00005400-000054ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:02:0d.0 System peripheral: Toshiba America Info Systems SD TypA
Controller (rev 03)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fcefee00 (32-bit, non-prefetchable)
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:07:00.0 Network controller: Intersil Corporation Intersil ISL3890 [Prism
GT/Prism Duette] (rev 01)
Subsystem: Standard Microsystems Corp [SMC]: Unknown device 2835
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 21000000 (32-bit, non-prefetchable) [disabled]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:0b:00.0 Ethernet controller: 3Com Corporation 3cCFE656 CardBus [Cyclone]
(rev 02)
Subsystem: 3Com Corporation 3CCFEM656 10/100 LAN+56K Modem CardBus
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 5000 [disabled] [size=532M]
Region 1: Memory at 21800000 (32-bit, non-prefetchable) [disabled]
[size=128]
Region 2: Memory at 21800080 (32-bit, non-prefetchable) [disabled]
[size=128]
Expansion ROM at 00020000 [disabled]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:0b:00.1 Communication controller: 3Com Corporation 3cCFEM656 10/100
LAN+56K Modem CardBus (rev 02)
Subsystem: 3Com Corporation 3CCFEM656 10/100 LAN+56K Modem CardBus
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 5080 [disabled]
Region 1: Memory at 21800100 (32-bit, non-prefetchable) [disabled]
[size=128]
Region 2: Memory at 21800180 (32-bit, non-prefetchable) [disabled]
[size=128]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
dmesg output after pcmcia services has been started is:
Linux version 2.6.8-gentoo-r8 (root at rover) (gcc version 3.3.4 20040623 (Gentoo
Linux 3.3.4-r1, ssp-3.3.2-2, pie-8.7.6)) #1 Wed Oct 13 11:58:19 MDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff40000 (usable)
BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data)
BIOS-e820: 000000001ff50000 - 0000000020000000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 130880
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126784 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 TOSHIB ) @ 0x000f01b0
ACPI: RSDT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ff40000
ACPI: FADT (v002 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ff40054
ACPI: DSDT (v001 TOSHIB 6100 0x20021015 MSFT 0x0100000a) @ 0x00000000
ACPI: PM-Timer IO Port: 0xee08
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Kernel-2.6.8-r8 ro root=304
Initializing CPU#0
CPU 0 irqstacks, hard=c03e3000 soft=c03e2000
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1595.296 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 514668k/523520k available (1976k kernel code, 8084k reserved, 808k
data, 140k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3153.92 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 3febf9ff 00000000 00000000 00000000
CPU: After vendor identify, caps: 3febf9ff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 3febf9ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel(R) Pentium(R) 4 Mobile CPU 1.60GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Level Trigger.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd5ad, last bus=5
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *11 12)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *11 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs *10)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f0470
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9138, dseg 0x0
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:0b.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:0b.1[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:0d.0[A] -> GSI 11 (level, low) -> IRQ 11
vesafb: framebuffer at 0xdc000000, mapped to 0xe0808000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:e720
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb1: VGA16 VGA frame buffer device
Machine check exception polling timer started.
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x1
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
Console: switching to colour frame buffer device 128x48
Linux agpgart interface v0.100 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 11 (level, low) -> IRQ 11
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xcfa0-0xcfa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xcfa8-0xcfaf, BIOS settings: hdc:DMA, hdd:pio
hda: IC25N030ATCS04-0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: UJDA720 DVD/CDRW, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB) w/1768KiB Cache, CHS=58140/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.02 loaded.
ieee1394: raw1394: /dev/raw1394 device initialized
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
PM: Reading pmdisk image.
PM: Resume from disk failed.
ACPI: (supports S0 S3 S4 S4bios S5)
ReiserFS: hda4: found reiserfs format "3.6" with standard journal
ReiserFS: hda4: using ordered data mode
ReiserFS: hda4: journal params: device hda4, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda4: checking transaction log (hda4)
ReiserFS: hda4: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 140k freed
Adding 747012k swap on /dev/hda3. Priority:-1 extents:1
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
<saw at saw.sw.com.sg> and others
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 11 (level, low) -> IRQ 11
eth0: OEM i82557/i82558 10/100 Ethernet, 00:00:39:89:17:D7, IRQ 11.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Real Time Clock Driver v1.12
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49451 usecs
intel8x0: clocking to 48000
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
lp0: using parport0 (interrupt-driven).
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Enabling device 0000:02:0a.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:0a.0 [12a3:ab01]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:0a.0, mfunc 0x01000002, devctl 0x60
Yenta: ISA IRQ mask 0x0000, PCI irq 11
Socket status: 30000059
PCI: Enabling device 0000:02:0b.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:0b.0[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:0b.0 [1179:0001]
Yenta: ISA IRQ mask 0x0038, PCI irq 11
Socket status: 30000007
PCI: Enabling device 0000:02:0b.1 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:0b.1[B] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:0b.1 [1179:0001]
Yenta: ISA IRQ mask 0x0038, PCI irq 11
Socket status: 30000007
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco.c 0.13e (David Gibson <hermes at gibson.dropbear.id.au> and others)
orinoco_cs.c 0.13e (David Gibson <hermes at gibson.dropbear.id.au> and others)
eth1: Station identity 001f:0001:0008:000a
eth1: Looks like a Lucent/Agere firmware version 8.10
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:02:2D:5C:9D:80
eth1: Station name "HERMES I"
eth1: ready
eth1: index 0x01: Vcc 3.3, irq 11, io 0x0100-0x013f
eth1: New link status: Connected (0001)
More information about the linux-pcmcia
mailing list