[PATCH] mmc: core: Initial support for SD express card/host
Ulf Hansson
ulf.hansson at linaro.org
Fri Aug 21 08:40:19 EDT 2020
Rui,
On Thu, 16 Jul 2020 at 16:16, Ulf Hansson <ulf.hansson at linaro.org> wrote:
>
> In the SD specification v7.10 the SD express card has been added. This new
> type of removable SD card, can be managed via a PCIe/NVMe based interface,
> while also allowing backwards compatibility towards the legacy SD
> interface.
>
> To keep the backwards compatibility, it's required to start the
> initialization through the legacy SD interface. If it turns out that the
> mmc host and the SD card, both supports the PCIe/NVMe interface, then a
> switch should be allowed.
>
> Therefore, let's introduce some basic support for this type of SD cards to
> the mmc core. The mmc host, should set MMC_CAP2_SD_EXP if it supports this
> interface and MMC_CAP2_SD_EXP_1_2V, if also 1.2V is supported, as to inform
> the core about it.
>
> To deal with the switch to the PCIe/NVMe interface, the mmc host is
> required to implement a new host ops, ->init_sd_express(). Based on the
> initial communication between the host and the card, host->ios.timing is
> set to either MMC_TIMING_SD_EXP or MMC_TIMING_SD_EXP_1_2V, depending on if
> 1.2V is supported or not. In this way, the mmc host can check these values
> in its ->init_sd_express() ops, to know how to proceed with the handover.
>
> Note that, to manage card insert/removal, the mmc core sticks with using
> the ->get_cd() callback, which means it's the host's responsibility to make
> sure it provides valid data, even if the card may be managed by PCIe/NVMe
> at the moment. As long as the card seems to be present, the mmc core keeps
> the card powered on.
>
> Cc: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
> Cc: Arnd Bergmann <arnd at arndb.de>
> Cc: Christoph Hellwig <hch at lst.de>
> Cc: Rui Feng <rui_feng at realsil.com.cn>
> Signed-off-by: Ulf Hansson <ulf.hansson at linaro.org>
Rui, did you manage to get some time to look at $subject patch?
If you need some help to understand what's needed to implement the
corresponding support in drivers/mmc/host/rtsx_pci_sdmmc.c, then
please just ask.
I think it would make sense to queue changes for rtsx_pci at the same
point as the mmc core changes. That's because I don't want to maintain
code in the mmc core that's left unused.
Kind regards
Uffe
> ---
> drivers/mmc/core/core.c | 15 ++++++++++--
> drivers/mmc/core/host.h | 6 +++++
> drivers/mmc/core/sd_ops.c | 49 +++++++++++++++++++++++++++++++++++++--
> drivers/mmc/core/sd_ops.h | 1 +
> include/linux/mmc/host.h | 7 ++++++
> 5 files changed, 74 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
> index 8ccae6452b9c..6673c0f33cc7 100644
> --- a/drivers/mmc/core/core.c
> +++ b/drivers/mmc/core/core.c
> @@ -2137,8 +2137,12 @@ static int mmc_rescan_try_freq(struct mmc_host *host, unsigned freq)
>
> mmc_go_idle(host);
>
> - if (!(host->caps2 & MMC_CAP2_NO_SD))
> - mmc_send_if_cond(host, host->ocr_avail);
> + if (!(host->caps2 & MMC_CAP2_NO_SD)) {
> + if (mmc_send_if_cond_pcie(host, host->ocr_avail))
> + goto out;
> + if (mmc_card_sd_express(host))
> + return 0;
> + }
>
> /* Order's important: probe SDIO, then SD, then MMC */
> if (!(host->caps2 & MMC_CAP2_NO_SDIO))
> @@ -2153,6 +2157,7 @@ static int mmc_rescan_try_freq(struct mmc_host *host, unsigned freq)
> if (!mmc_attach_mmc(host))
> return 0;
>
> +out:
> mmc_power_off(host);
> return -EIO;
> }
> @@ -2280,6 +2285,12 @@ void mmc_rescan(struct work_struct *work)
> goto out;
> }
>
> + /* If an SD express card is present, then leave it as is. */
> + if (mmc_card_sd_express(host)) {
> + mmc_release_host(host);
> + goto out;
> + }
> +
> for (i = 0; i < ARRAY_SIZE(freqs); i++) {
> unsigned int freq = freqs[i];
> if (freq > host->f_max) {
> diff --git a/drivers/mmc/core/host.h b/drivers/mmc/core/host.h
> index 5e3b9534ffb2..ba407617ed23 100644
> --- a/drivers/mmc/core/host.h
> +++ b/drivers/mmc/core/host.h
> @@ -77,5 +77,11 @@ static inline bool mmc_card_hs400es(struct mmc_card *card)
> return card->host->ios.enhanced_strobe;
> }
>
> +static inline bool mmc_card_sd_express(struct mmc_host *host)
> +{
> + return host->ios.timing == MMC_TIMING_SD_EXP ||
> + host->ios.timing == MMC_TIMING_SD_EXP_1_2V;
> +}
> +
> #endif
>
> diff --git a/drivers/mmc/core/sd_ops.c b/drivers/mmc/core/sd_ops.c
> index 22bf528294b9..d61ff811218c 100644
> --- a/drivers/mmc/core/sd_ops.c
> +++ b/drivers/mmc/core/sd_ops.c
> @@ -158,7 +158,8 @@ int mmc_send_app_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr)
> return err;
> }
>
> -int mmc_send_if_cond(struct mmc_host *host, u32 ocr)
> +static int __mmc_send_if_cond(struct mmc_host *host, u32 ocr, u8 pcie_bits,
> + u32 *resp)
> {
> struct mmc_command cmd = {};
> int err;
> @@ -171,7 +172,7 @@ int mmc_send_if_cond(struct mmc_host *host, u32 ocr)
> * SD 1.0 cards.
> */
> cmd.opcode = SD_SEND_IF_COND;
> - cmd.arg = ((ocr & 0xFF8000) != 0) << 8 | test_pattern;
> + cmd.arg = ((ocr & 0xFF8000) != 0) << 8 | pcie_bits << 8 | test_pattern;
> cmd.flags = MMC_RSP_SPI_R7 | MMC_RSP_R7 | MMC_CMD_BCR;
>
> err = mmc_wait_for_cmd(host, &cmd, 0);
> @@ -186,6 +187,50 @@ int mmc_send_if_cond(struct mmc_host *host, u32 ocr)
> if (result_pattern != test_pattern)
> return -EIO;
>
> + if (resp)
> + *resp = cmd.resp[0];
> +
> + return 0;
> +}
> +
> +int mmc_send_if_cond(struct mmc_host *host, u32 ocr)
> +{
> + return __mmc_send_if_cond(host, ocr, 0, NULL);
> +}
> +
> +int mmc_send_if_cond_pcie(struct mmc_host *host, u32 ocr)
> +{
> + u32 resp = 0;
> + u8 pcie_bits = 0;
> + int ret;
> +
> + if (host->caps2 & MMC_CAP2_SD_EXP) {
> + /* Probe card for SD express support via PCIe. */
> + pcie_bits = 0x10;
> + if (host->caps2 & MMC_CAP2_SD_EXP_1_2V)
> + /* Probe also for 1.2V support. */
> + pcie_bits = 0x30;
> + }
> +
> + ret = __mmc_send_if_cond(host, ocr, pcie_bits, &resp);
> + if (ret)
> + return 0;
> +
> + /* Continue with the SD express init, if the card supports it. */
> + resp &= 0x3000;
> + if (pcie_bits && resp) {
> + if (resp == 0x3000)
> + host->ios.timing = MMC_TIMING_SD_EXP_1_2V;
> + else
> + host->ios.timing = MMC_TIMING_SD_EXP;
> +
> + /*
> + * According to the spec the clock shall also be gated, but
> + * let's leave this to the host driver for more flexibility.
> + */
> + return host->ops->init_sd_express(host, &host->ios);
> + }
> +
> return 0;
> }
>
> diff --git a/drivers/mmc/core/sd_ops.h b/drivers/mmc/core/sd_ops.h
> index 2194cabfcfc5..3ba7b3cf4652 100644
> --- a/drivers/mmc/core/sd_ops.h
> +++ b/drivers/mmc/core/sd_ops.h
> @@ -16,6 +16,7 @@ struct mmc_host;
> int mmc_app_set_bus_width(struct mmc_card *card, int width);
> int mmc_send_app_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr);
> int mmc_send_if_cond(struct mmc_host *host, u32 ocr);
> +int mmc_send_if_cond_pcie(struct mmc_host *host, u32 ocr);
> int mmc_send_relative_addr(struct mmc_host *host, unsigned int *rca);
> int mmc_app_send_scr(struct mmc_card *card);
> int mmc_sd_switch(struct mmc_card *card, int mode, int group,
> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> index c5b6e97cb21a..905cddc5e6f3 100644
> --- a/include/linux/mmc/host.h
> +++ b/include/linux/mmc/host.h
> @@ -60,6 +60,8 @@ struct mmc_ios {
> #define MMC_TIMING_MMC_DDR52 8
> #define MMC_TIMING_MMC_HS200 9
> #define MMC_TIMING_MMC_HS400 10
> +#define MMC_TIMING_SD_EXP 11
> +#define MMC_TIMING_SD_EXP_1_2V 12
>
> unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
>
> @@ -172,6 +174,9 @@ struct mmc_host_ops {
> */
> int (*multi_io_quirk)(struct mmc_card *card,
> unsigned int direction, int blk_size);
> +
> + /* Initialize an SD express card, mandatory for MMC_CAP2_SD_EXP. */
> + int (*init_sd_express)(struct mmc_host *host, struct mmc_ios *ios);
> };
>
> struct mmc_cqe_ops {
> @@ -357,6 +362,8 @@ struct mmc_host {
> #define MMC_CAP2_HS200_1_2V_SDR (1 << 6) /* can support */
> #define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \
> MMC_CAP2_HS200_1_2V_SDR)
> +#define MMC_CAP2_SD_EXP (1 << 7) /* SD express via PCIe */
> +#define MMC_CAP2_SD_EXP_1_2V (1 << 8) /* SD express 1.2V */
> #define MMC_CAP2_CD_ACTIVE_HIGH (1 << 10) /* Card-detect signal active high */
> #define MMC_CAP2_RO_ACTIVE_HIGH (1 << 11) /* Write-protect signal active high */
> #define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14) /* Don't power up before scan */
> --
> 2.20.1
>
More information about the Linux-nvme
mailing list