S600=> run bootcmd
## Booting image at fe100000 ...
   Image Name:   Linux-2.6.20-S600-Ver1.1
   Created:      2009-12-22   8:05:57 UTC
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1727328 Bytes =  1.6 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
   Booting using the fdt at 0xfe500000
   Loading Device Tree to 007fd000, end 007fee14 ... OK
setup_arch: bootmem
mpc8313_rdb_setup_arch()
arch: exit

[    0.000000] Using MPC8313 RDB machine description
[    0.000000] Linux version 2.6.20-S600-Ver1.1 (root@leapfrogserver) (gcc version 4.0.2 20060628 (Wasabi)) #31 Tue Dec 22 13
:35:54 IST 2009
[    0.000000] Found MPC83xx PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->    32768
[    0.000000]   Normal      32768 ->    32768
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->    32768
[    0.000000] Built 1 zonelists.  Total pages: 32512
[    0.000000] Kernel command line: root=/dev/mtdblock9 rootfstype=jffs2 rw console=ttyS0,115200
[    0.000000] IPIC (128 IRQ sources) at fdefa700
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[   14.757860] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[   14.758634] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[   14.771757] Memory: 126148k/131072k available (3008k kernel code, 4772k reserved, 464k data, 98k bss, 144k init)
[   14.853637] Mount-cache hash table entries: 512
[   14.856914] NET: Registered protocol family 16
[   14.863234] PCI: Probing PCI hardware
[   14.871601] Generic PHY: Registered new driver
[   14.872289] SCSI subsystem initialized
[   14.872967] usbcore: registered new interface driver usbfs
[   14.873279] usbcore: registered new interface driver hub
[   14.873699] usbcore: registered new device driver usb
[   14.876829] NET: Registered protocol family 2
[   14.901653] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[   14.902117] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[   14.902285] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[   14.902373] TCP: Hash tables configured (established 4096 bind 2048)
[   14.902390] TCP reno registered
[   14.927081] JFFS2 version 2.2. (NAND) (SUMMARY)  (C) 2001-2006 Red Hat, Inc.
[   14.927465] io scheduler noop registered
[   14.927486] io scheduler anticipatory registered (default)
[   14.927504] io scheduler deadline registered
[   14.927590] io scheduler cfq registered
[   15.176011] Generic RTC Driver v1.07
[   15.176334] device node obtained!
[   15.176404] sram_irq = 48
[   15.176742] Sram driver inserted
[   15.177311] WDT driver for MPC83xx initialized. mode:reset timeout=65535 (25 seconds)
[   15.177367] Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
[   15.188383] serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 16) is a 16550A
[   15.411810] serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 17) is a 16550A
[   15.440655] serial8250.0: ttyS2 at MMIO 0xfa000000 (irq = 18) is a ST16654
[   15.469587] serial8250.0: ttyS3 at MMIO 0xfa000008 (irq = 18) is a ST16654
[   15.498525] serial8250.0: ttyS4 at MMIO 0xfa000010 (irq = 18) is a ST16654
[   15.527416] serial8250.0: ttyS5 at MMIO 0xfa000018 (irq = 18) is a ST16654
[   15.556316] serial8250.0: ttyS6 at MMIO 0xfa000020 (irq = 19) is a ST16654
[   15.585214] serial8250.0: ttyS7 at MMIO 0xfa000028 (irq = 19) is a ST16654
[   15.614111] serial8250.0: ttyS8 at MMIO 0xfa000030 (irq = 19) is a ST16654
[   15.643037] serial8250.0: ttyS9 at MMIO 0xfa000038 (irq = 19) is a ST16654
[   15.671938] serial8250.0: ttyS10 at MMIO 0xfa000040 (irq = 20) is a ST16654
[   15.700928] serial8250.0: ttyS11 at MMIO 0xfa000048 (irq = 20) is a ST16654
[   15.729916] serial8250.0: ttyS12 at MMIO 0xfa000050 (irq = 20) is a ST16654
[   15.758952] serial8250.0: ttyS13 at MMIO 0xfa000058 (irq = 20) is a ST16654
[   15.771844] RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
[   15.781949] loop: loaded (max 8 devices)
[   15.785992] Intel(R) PRO/1000 Network Driver - version 7.3.15-k2-NAPI
[   15.792435] Copyright (c) 1999-2006 Intel Corporation.
[   15.805043] Gianfar MII Bus: probed
[   15.809444] eth0: Gianfar Ethernet Controller Version 1.4, 00:e0:0c:00:7e:22
[   15.816747] eth0: MTU = 1500 (frame size=1540,truesize=2296)
[   15.822413] eth0: Running with NAPI enabled
[   15.826604] eth0: 64/64 RX/TX BD ring size
[   15.830705] eth0: Socket buffer recycling mode enabled
[   15.836391] eth1: Gianfar Ethernet Controller Version 1.4, 00:e0:0c:00:7e:21
[   15.843674] eth1: MTU = 1500 (frame size=1540,truesize=2296)
[   15.849353] eth1: Running with NAPI enabled
[   15.853550] eth1: 64/64 RX/TX BD ring size
[   15.857652] eth1: Socket buffer recycling mode enabled
[   15.862819] SKB Handler initialized(max=64)
[   15.867568] Marvell 88E1101: Registered new driver
[   15.872639] Marvell 88E1111: Registered new driver
[   15.877715] Marvell 88E1145: Registered new driver
[   15.882802] MPC8313ERDB Ethernet Switch: Registered new driver
[   15.890713] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[   15.899000] MPC8313RDB flash device: 1000000 at fe000000 Partition number 4
[   15.907173] MPC8313RDB Flash Map Info: Found 1 x16 devices at 0x0 in 16-bit bank
[   15.914643]  Amd/Fujitsu Extended Query Table at 0x0040
[   15.919888] MPC8313RDB Flash Map Info: CFI does not contain boot bank location. Assuming top.
[   15.928411] number of CFI chips: 1
[   15.931824] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
[   15.939565] Creating 4 MTD partitions on "MPC8313RDB Flash Map Info":
[   15.946014] 0x00000000-0x00100000 : "U-Boot"
[   15.951146] 0x00100000-0x00500000 : "Kernel"
[   15.956365] 0x00500000-0x00580000 : "dtb"
[   15.961279] 0x00580000-0x01000000 : "RFS"
[   15.966299] MPC8313RDB flash device (MPC8313RDB Flash Map Info) initialized
[   15.973281] Freescale eLBC NAND Driver (C) 2006 Freescale
[   15.979359] NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
[   15.987999] Scanning device for bad blocks
[   16.078127] Bad eraseblock 257 at 0x02020000
[   16.090414] Bad eraseblock 281 at 0x02320000
[   16.152366] Bad eraseblock 454 at 0x038c0000
[   16.316603] Bad eraseblock 934 at 0x074c0000
[   16.350559] Bad eraseblock 1023 at 0x07fe0000
[   16.696159] fsl-elbc fsl-elbc.0: Using OF partition information
[   16.702096] Creating 7 MTD partitions on "nand0":
[   16.706810] 0x00000000-0x00100000 : "U-Boot-NAND"
[   16.712384] 0x00100000-0x00500000 : "Kernel1"
[   16.717708] 0x00500000-0x00900000 : "Kernel2"
[   16.723027] 0x00900000-0x00980000 : "DTB1"
[   16.728067] 0x00980000-0x00a00000 : "DTB2"
[   16.733156] 0x00a00000-0x08500000 : "RFS1"
[   16.738385] 0x084c0000-0x0ffc0000 : "RFS2"
[   16.743642] usbmon: debugfs is not available
[   16.748250] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[   16.755236] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[   16.785429] fsl-ehci fsl-ehci.0: irq 38, io base 0xe0023000
[   16.791026] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   16.799256] usb usb1: configuration #1 chosen from 1 choice
[   16.805243] hub 1-0:1.0: USB hub found
[   16.809081] hub 1-0:1.0: 1 port detected
[   16.914411] Initializing USB Mass Storage driver...
[   16.919561] usbcore: registered new interface driver usb-storage
[   16.925598] USB Mass Storage support registered.
[   16.930251] Freescale High-Speed USB SOC Device Controller driver (Feb 5, 2007)
[   16.937831] i2c /dev entries driver
[   17.949746] TCP cubic registered
[   17.953020] NET: Registered protocol family 1
[   17.957421] NET: Registered protocol family 17
[   18.036678] Empty flash at 0x003a05b0 ends at 0x003a0800
[   19.358927] VFS: Mounted root (jffs2 filesystem).
[   19.363823] Freeing unused kernel memory: 144k init
[   43.785920] JFFS2 notice: (776) check_node_data: wrong data CRC in data node at 0x003a1800: read 0x64066ebe, calculated 0x
95380938.
Setting the hostname to freescale
Mounting filesystems
Running sysctl
Setting up networking on loopback device:
Setting up networking on eth0:
Adding static route for default gateway to 192.168.32.47:
SIOCADDRT: Network is unreachable
Setting nameserver to 192.168.1.1 in /etc/resolv.conf:
Setting up networking on eth1:
Adding static route for default gateway to 192.168.1.1:
Setting nameserver to 192.168.1.1 in /etc/resolv.conf:
Starting inetd:


        Welcome to Freescale Semiconductor Embedded Linux Environment

!!!!! WARNING !!!!!!!

The default password for the root account is: root
please change this password using the 'passwd' command
and then edit this message (/etc/issue) to remove this message

freescale login: [   47.401647] PHY: e0024520:11 - Link is Up - 100/Full
