Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>

Index: drivers/mtd/nand/au1550nd.c
===================================================================
RCS file: /home/cvs/mtd/drivers/mtd/nand/au1550nd.c,v
retrieving revision 1.12
diff -a -u -p -r1.12 au1550nd.c
--- drivers/mtd/nand/au1550nd.c	23 Sep 2005 01:44:55 -0000	1.12
+++ drivers/mtd/nand/au1550nd.c	29 Oct 2005 20:04:23 -0000
@@ -14,6 +14,7 @@
 #include <linux/slab.h>
 #include <linux/init.h>
 #include <linux/module.h>
+#include <linux/interrupt.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/nand.h>
 #include <linux/mtd/partitions.h>
@@ -313,6 +314,141 @@ int au1550_device_ready(struct mtd_info 
 	return ret;
 }
 
+/**
+ * au1550_select_chip - control -CE line
+ *	Forbid driving -CE manually permitting the NAND controller to do this.
+ *	Keeping -CE asserted during the whole sector reads interferes with the
+ *	NOR flash and PCMCIA drivers as it causes contention on the static bus.
+ *	We only have to hold -CE low for the NAND read commands since the flash
+ *	chip needs it to be asserted during chip not ready time but the NAND
+ *	controller keeps it released.
+ *
+ * @mtd:	MTD device structure
+ * @chip:	chipnumber to select, -1 for deselect
+ */
+static void au1550_select_chip(struct mtd_info *mtd, int chip)
+{
+}
+
+/**
+ * au1550_command - Send command to NAND device
+ * @mtd:	MTD device structure
+ * @command:	the command to be sent
+ * @column:	the column address for this command, -1 if none
+ * @page_addr:	the page address for this command, -1 if none
+ */
+static void au1550_command(struct mtd_info *mtd, unsigned command, int column, int page_addr)
+{
+	register struct nand_chip *this = mtd->priv;
+	int ce_override = 0, i;
+	ulong flags;
+
+	/* Begin command latch cycle */
+	this->hwcontrol(mtd, NAND_CTL_SETCLE);
+	/*
+	 * Write out the command to the device.
+	 */
+	if (command == NAND_CMD_SEQIN) {
+		int readcmd;
+
+		if (column >= mtd->oobblock) {
+			/* OOB area */
+			column -= mtd->oobblock;
+			readcmd = NAND_CMD_READOOB;
+		} else if (column < 256) {
+			/* First 256 bytes --> READ0 */
+			readcmd = NAND_CMD_READ0;
+		} else {
+			column -= 256;
+			readcmd = NAND_CMD_READ1;
+		}
+		this->write_byte(mtd, readcmd);
+	}
+	this->write_byte(mtd, command);
+
+	/* Set ALE and clear CLE to start address cycle */
+	this->hwcontrol(mtd, NAND_CTL_CLRCLE);
+
+	if (column != -1 || page_addr != -1) {
+		this->hwcontrol(mtd, NAND_CTL_SETALE);
+
+		/* Serially input address */
+		if (column != -1) {
+			/* Adjust columns for 16 bit buswidth */
+			if (this->options & NAND_BUSWIDTH_16)
+				column >>= 1;
+			this->write_byte(mtd, column);
+		}
+		if (page_addr != -1) {
+			this->write_byte(mtd, (u8)(page_addr & 0xff));
+
+			if (command == NAND_CMD_READ0 ||
+			    command == NAND_CMD_READ1 ||
+			    command == NAND_CMD_READOOB) {
+				/*
+				 * NAND controller will release -CE after
+				 * the last address byte is written, so we'll
+				 * have to forcibly assert it. No interrupts
+				 * are allowed while we do this as we don't
+				 * want the NOR flash or PCMCIA drivers to
+				 * steal our precious bytes of data...
+				 */
+				ce_override = 1;
+				local_irq_save(flags);
+				this->hwcontrol(mtd, NAND_CTL_SETNCE);
+			}
+
+			this->write_byte(mtd, (u8)(page_addr >> 8));
+
+			/* One more address cycle for devices > 32MiB */
+			if (this->chipsize > (32 << 20))
+				this->write_byte(mtd, (u8)((page_addr >> 16) & 0x0f));
+		}
+		/* Latch in address */
+		this->hwcontrol(mtd, NAND_CTL_CLRALE);
+	}
+
+	/*
+	 * Program and erase have their own busy handlers.
+	 * Status and sequential in need no delay.
+	 */
+	switch (command) {
+
+	case NAND_CMD_PAGEPROG:
+	case NAND_CMD_ERASE1:
+	case NAND_CMD_ERASE2:
+	case NAND_CMD_SEQIN:
+	case NAND_CMD_STATUS:
+		return;
+
+	case NAND_CMD_RESET:
+		break;
+
+	case NAND_CMD_READ0:
+	case NAND_CMD_READ1:
+	case NAND_CMD_READOOB:
+		/* Check if we're really driving -CE low (just in case) */
+		if (unlikely(!ce_override))
+			break;
+
+		/* Apply a short delay always to ensure that we do wait tWB. */
+		ndelay(100);
+		/* Wait for a chip to become ready... */
+		for (i = this->chip_delay; !this->dev_ready(mtd) && i > 0; --i)
+			udelay(1);
+
+		/* Release -CE and re-enable interrupts. */
+		this->hwcontrol(mtd, NAND_CTL_CLRNCE);
+		local_irq_restore(flags);
+		return;
+	}
+	/* Apply this short delay always to ensure that we do wait tWB. */
+	ndelay(100);
+
+	while(!this->dev_ready(mtd));
+}
+
+
 /*
  * Main initialization routine
  */
@@ -437,6 +573,9 @@ int __init au1xxx_nand_init (void)
 	/* Set address of hardware control function */
 	this->hwcontrol = au1550_hwcontrol;
 	this->dev_ready = au1550_device_ready;
+	this->select_chip = au1550_select_chip;
+	this->cmdfunc = au1550_command;
+
 	/* 30 us command delay time */
 	this->chip_delay = 30;		
 	this->eccmode = NAND_ECC_SOFT;