[PATCH 2/2] mtd: spinand: esmt: Extend IDs to 5 bytes

Martin Kurbanov mmkurbanov at salutedevices.com
Fri Jan 26 10:48:23 PST 2024



On 25.01.2024 23:01, Ezra Buehler wrote:
> From: Ezra Buehler <ezra.buehler at husqvarnagroup.com>
> 
> According to the datasheets, the ESMT chips in question will return a 5
> byte long identification code where the last 3 bytes are the JEDEC
> continuation codes (7Fh). Although, I would have expected 4 continuation
> codes as Powerchip Semiconductor (C8h, corresponding to the parameter
> page data) is located in bank 5 of the JEDEC database.
> 
> By matching the full 5 bytes we can avoid clashes with GigaDevice NAND
> flashes.
> 
> This fix allows the MT7688-based GARDENA smart Gateway to boot again.
> 
> Fixes: aa08bf187f32 ("mtd: spinand: esmt: add support for F50D2G41KA")
> Signed-off-by: Ezra Buehler <ezra.buehler at husqvarnagroup.com>


Tested for F50L1G41LB

Reviewed-by: Martin Kurbanov <mmkurbanov at salutedevices.com>
Tested-by: Martin Kurbanov <mmkurbanov at salutedevices.com>

> ---
>  drivers/mtd/nand/spi/esmt.c | 9 ++++++---
>  1 file changed, 6 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/mtd/nand/spi/esmt.c b/drivers/mtd/nand/spi/esmt.c
> index 31c439a557b1..4597a82de23a 100644
> --- a/drivers/mtd/nand/spi/esmt.c
> +++ b/drivers/mtd/nand/spi/esmt.c
> @@ -104,7 +104,8 @@ static const struct mtd_ooblayout_ops f50l1g41lb_ooblayout = {
>  
>  static const struct spinand_info esmt_c8_spinand_table[] = {
>  	SPINAND_INFO("F50L1G41LB",
> -		     SPINAND_ID(SPINAND_READID_METHOD_OPCODE_ADDR, 0x01),
> +		     SPINAND_ID(SPINAND_READID_METHOD_OPCODE_ADDR, 0x01, 0x7f,
> +				0x7f, 0x7f),
>  		     NAND_MEMORG(1, 2048, 64, 64, 1024, 20, 1, 1, 1),
>  		     NAND_ECCREQ(1, 512),
>  		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,
> @@ -113,7 +114,8 @@ static const struct spinand_info esmt_c8_spinand_table[] = {
>  		     0,
>  		     SPINAND_ECCINFO(&f50l1g41lb_ooblayout, NULL)),
>  	SPINAND_INFO("F50D1G41LB",
> -		     SPINAND_ID(SPINAND_READID_METHOD_OPCODE_ADDR, 0x11),
> +		     SPINAND_ID(SPINAND_READID_METHOD_OPCODE_ADDR, 0x11, 0x7f,
> +				0x7f, 0x7f),
>  		     NAND_MEMORG(1, 2048, 64, 64, 1024, 20, 1, 1, 1),
>  		     NAND_ECCREQ(1, 512),
>  		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,
> @@ -122,7 +124,8 @@ static const struct spinand_info esmt_c8_spinand_table[] = {
>  		     0,
>  		     SPINAND_ECCINFO(&f50l1g41lb_ooblayout, NULL)),
>  	SPINAND_INFO("F50D2G41KA",
> -		     SPINAND_ID(SPINAND_READID_METHOD_OPCODE_ADDR, 0x51),
> +		     SPINAND_ID(SPINAND_READID_METHOD_OPCODE_ADDR, 0x51, 0x7f,
> +				0x7f, 0x7f),
>  		     NAND_MEMORG(1, 2048, 128, 64, 2048, 40, 1, 1, 1),
>  		     NAND_ECCREQ(8, 512),
>  		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,

-- 
Best Regards,
Martin Kurbanov



More information about the linux-mtd mailing list