[PATCH v2 1/6] mtd: spi-nor: Remove support for Xilinx S3AN flashes
Ricardo Ribalda Delgado
ribalda at kernel.org
Fri Apr 19 08:16:05 PDT 2024
Hi Michael
Thanks for the cleanup. I have pinged my previous employer and they do
not have any product in production using S3AN.
So no blockers from my side.
[ccing Marek In case he knows about other users]
Regards
On Fri, Apr 19, 2024 at 4:14 PM Michael Walle <mwalle at kernel.org> wrote:
>
> These flashes are kind of an oddball for the very old Xilinx Spartan 3
> FPGAs to store their bitstream. More importantly, they reuse the Atmel
> JEDEC manufacturer ID and in fact the at45db081d already blocks the use
> of the 3S700AN flash chip. It's time to sunset support for these
> flashes.
>
> Signed-off-by: Michael Walle <mwalle at kernel.org>
> Acked-by: Tudor Ambarus <tudor.ambarus at linaro.org>
> Reviewed-by: Pratyush Yadav <pratyush at kernel.org>
> Cc: Ricardo Ribalda <ribalda at kernel.org>
Acked-by: Ricardo Ribalda <ribalda at chromium.org>
> ---
> drivers/mtd/spi-nor/Makefile | 1 -
> drivers/mtd/spi-nor/core.c | 1 -
> drivers/mtd/spi-nor/core.h | 1 -
> drivers/mtd/spi-nor/xilinx.c | 169 -----------------------------------
> 4 files changed, 172 deletions(-)
> delete mode 100644 drivers/mtd/spi-nor/xilinx.c
>
> diff --git a/drivers/mtd/spi-nor/Makefile b/drivers/mtd/spi-nor/Makefile
> index 5e68468b72fc..5dd9c35f6b6f 100644
> --- a/drivers/mtd/spi-nor/Makefile
> +++ b/drivers/mtd/spi-nor/Makefile
> @@ -13,7 +13,6 @@ spi-nor-objs += micron-st.o
> spi-nor-objs += spansion.o
> spi-nor-objs += sst.o
> spi-nor-objs += winbond.o
> -spi-nor-objs += xilinx.o
> spi-nor-objs += xmc.o
> spi-nor-$(CONFIG_DEBUG_FS) += debugfs.o
> obj-$(CONFIG_MTD_SPI_NOR) += spi-nor.o
> diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
> index 3e1f1913536b..cbe5f92eb0af 100644
> --- a/drivers/mtd/spi-nor/core.c
> +++ b/drivers/mtd/spi-nor/core.c
> @@ -1986,7 +1986,6 @@ static const struct spi_nor_manufacturer *manufacturers[] = {
> &spi_nor_spansion,
> &spi_nor_sst,
> &spi_nor_winbond,
> - &spi_nor_xilinx,
> &spi_nor_xmc,
> };
>
> diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
> index 442786685515..072c69b0d06c 100644
> --- a/drivers/mtd/spi-nor/core.h
> +++ b/drivers/mtd/spi-nor/core.h
> @@ -603,7 +603,6 @@ extern const struct spi_nor_manufacturer spi_nor_st;
> extern const struct spi_nor_manufacturer spi_nor_spansion;
> extern const struct spi_nor_manufacturer spi_nor_sst;
> extern const struct spi_nor_manufacturer spi_nor_winbond;
> -extern const struct spi_nor_manufacturer spi_nor_xilinx;
> extern const struct spi_nor_manufacturer spi_nor_xmc;
>
> extern const struct attribute_group *spi_nor_sysfs_groups[];
> diff --git a/drivers/mtd/spi-nor/xilinx.c b/drivers/mtd/spi-nor/xilinx.c
> deleted file mode 100644
> index f99118c691b0..000000000000
> --- a/drivers/mtd/spi-nor/xilinx.c
> +++ /dev/null
> @@ -1,169 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -/*
> - * Copyright (C) 2005, Intec Automation Inc.
> - * Copyright (C) 2014, Freescale Semiconductor, Inc.
> - */
> -
> -#include <linux/mtd/spi-nor.h>
> -
> -#include "core.h"
> -
> -#define XILINX_OP_SE 0x50 /* Sector erase */
> -#define XILINX_OP_PP 0x82 /* Page program */
> -#define XILINX_OP_RDSR 0xd7 /* Read status register */
> -
> -#define XSR_PAGESIZE BIT(0) /* Page size in Po2 or Linear */
> -#define XSR_RDY BIT(7) /* Ready */
> -
> -#define XILINX_RDSR_OP(buf) \
> - SPI_MEM_OP(SPI_MEM_OP_CMD(XILINX_OP_RDSR, 0), \
> - SPI_MEM_OP_NO_ADDR, \
> - SPI_MEM_OP_NO_DUMMY, \
> - SPI_MEM_OP_DATA_IN(1, buf, 0))
> -
> -#define S3AN_FLASH(_id, _name, _n_sectors, _page_size) \
> - .id = _id, \
> - .name = _name, \
> - .size = 8 * (_page_size) * (_n_sectors), \
> - .sector_size = (8 * (_page_size)), \
> - .page_size = (_page_size), \
> - .flags = SPI_NOR_NO_FR
> -
> -/* Xilinx S3AN share MFR with Atmel SPI NOR */
> -static const struct flash_info xilinx_nor_parts[] = {
> - /* Xilinx S3AN Internal Flash */
> - { S3AN_FLASH(SNOR_ID(0x1f, 0x22, 0x00), "3S50AN", 64, 264) },
> - { S3AN_FLASH(SNOR_ID(0x1f, 0x24, 0x00), "3S200AN", 256, 264) },
> - { S3AN_FLASH(SNOR_ID(0x1f, 0x24, 0x00), "3S400AN", 256, 264) },
> - { S3AN_FLASH(SNOR_ID(0x1f, 0x25, 0x00), "3S700AN", 512, 264) },
> - { S3AN_FLASH(SNOR_ID(0x1f, 0x26, 0x00), "3S1400AN", 512, 528) },
> -};
> -
> -/*
> - * This code converts an address to the Default Address Mode, that has non
> - * power of two page sizes. We must support this mode because it is the default
> - * mode supported by Xilinx tools, it can access the whole flash area and
> - * changing over to the Power-of-two mode is irreversible and corrupts the
> - * original data.
> - * Addr can safely be unsigned int, the biggest S3AN device is smaller than
> - * 4 MiB.
> - */
> -static u32 s3an_nor_convert_addr(struct spi_nor *nor, u32 addr)
> -{
> - u32 page_size = nor->params->page_size;
> - u32 offset, page;
> -
> - offset = addr % page_size;
> - page = addr / page_size;
> - page <<= (page_size > 512) ? 10 : 9;
> -
> - return page | offset;
> -}
> -
> -/**
> - * xilinx_nor_read_sr() - Read the Status Register on S3AN flashes.
> - * @nor: pointer to 'struct spi_nor'.
> - * @sr: pointer to a DMA-able buffer where the value of the
> - * Status Register will be written.
> - *
> - * Return: 0 on success, -errno otherwise.
> - */
> -static int xilinx_nor_read_sr(struct spi_nor *nor, u8 *sr)
> -{
> - int ret;
> -
> - if (nor->spimem) {
> - struct spi_mem_op op = XILINX_RDSR_OP(sr);
> -
> - spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
> -
> - ret = spi_mem_exec_op(nor->spimem, &op);
> - } else {
> - ret = spi_nor_controller_ops_read_reg(nor, XILINX_OP_RDSR, sr,
> - 1);
> - }
> -
> - if (ret)
> - dev_dbg(nor->dev, "error %d reading SR\n", ret);
> -
> - return ret;
> -}
> -
> -/**
> - * xilinx_nor_sr_ready() - Query the Status Register of the S3AN flash to see
> - * if the flash is ready for new commands.
> - * @nor: pointer to 'struct spi_nor'.
> - *
> - * Return: 1 if ready, 0 if not ready, -errno on errors.
> - */
> -static int xilinx_nor_sr_ready(struct spi_nor *nor)
> -{
> - int ret;
> -
> - ret = xilinx_nor_read_sr(nor, nor->bouncebuf);
> - if (ret)
> - return ret;
> -
> - return !!(nor->bouncebuf[0] & XSR_RDY);
> -}
> -
> -static int xilinx_nor_setup(struct spi_nor *nor,
> - const struct spi_nor_hwcaps *hwcaps)
> -{
> - u32 page_size;
> - int ret;
> -
> - ret = xilinx_nor_read_sr(nor, nor->bouncebuf);
> - if (ret)
> - return ret;
> -
> - nor->erase_opcode = XILINX_OP_SE;
> - nor->program_opcode = XILINX_OP_PP;
> - nor->read_opcode = SPINOR_OP_READ;
> - nor->flags |= SNOR_F_NO_OP_CHIP_ERASE;
> -
> - /*
> - * This flashes have a page size of 264 or 528 bytes (known as
> - * Default addressing mode). It can be changed to a more standard
> - * Power of two mode where the page size is 256/512. This comes
> - * with a price: there is 3% less of space, the data is corrupted
> - * and the page size cannot be changed back to default addressing
> - * mode.
> - *
> - * The current addressing mode can be read from the XRDSR register
> - * and should not be changed, because is a destructive operation.
> - */
> - if (nor->bouncebuf[0] & XSR_PAGESIZE) {
> - /* Flash in Power of 2 mode */
> - page_size = (nor->params->page_size == 264) ? 256 : 512;
> - nor->params->page_size = page_size;
> - nor->mtd.writebufsize = page_size;
> - nor->params->size = nor->info->size;
> - nor->mtd.erasesize = 8 * page_size;
> - } else {
> - /* Flash in Default addressing mode */
> - nor->params->convert_addr = s3an_nor_convert_addr;
> - nor->mtd.erasesize = nor->info->sector_size;
> - }
> -
> - return 0;
> -}
> -
> -static int xilinx_nor_late_init(struct spi_nor *nor)
> -{
> - nor->params->setup = xilinx_nor_setup;
> - nor->params->ready = xilinx_nor_sr_ready;
> -
> - return 0;
> -}
> -
> -static const struct spi_nor_fixups xilinx_nor_fixups = {
> - .late_init = xilinx_nor_late_init,
> -};
> -
> -const struct spi_nor_manufacturer spi_nor_xilinx = {
> - .name = "xilinx",
> - .parts = xilinx_nor_parts,
> - .nparts = ARRAY_SIZE(xilinx_nor_parts),
> - .fixups = &xilinx_nor_fixups,
> -};
> --
> 2.39.2
>
More information about the linux-mtd
mailing list