[RFT PATCH] mtd: rawnand: ingenic: move the GPIO quirk to gpiolib-of.c

[Andy Shevchenko]

On Tue, Sep 26, 2023 at 11:06:23AM +0200, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski at linaro.org>
> 
> We have a special place for OF polarity quirks in gpiolib-of.c. Let's
> move this over there so that it doesn't pollute the driver.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski at linaro.org>
> ---
> This is an alternative to the previous patch that instead of replacing
> one active-low setter with another, just moves the quirk over to
> gpiolib-of.c

Much better than that in my opinion.
Reviewed-by: Andy Shevchenko <andy at kernel.org>

>  drivers/gpio/gpiolib-of.c                       |  9 +++++++++
>  drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c | 12 ------------
>  2 files changed, 9 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
> index 5515f32cf19b..58c0bbe9d569 100644
> --- a/drivers/gpio/gpiolib-of.c
> +++ b/drivers/gpio/gpiolib-of.c
> @@ -192,6 +192,15 @@ static void of_gpio_try_fixup_polarity(const struct device_node *np,
>  		 */
>  		{ "himax,hx8357",	"gpios-reset",	false },
>  		{ "himax,hx8369",	"gpios-reset",	false },
> +		/*
> +		 * The rb-gpios semantics was undocumented and qi,lb60 (along with
> +		 * the ingenic driver) got it wrong. The active state encodes the
> +		 * NAND ready state, which is high level. Since there's no signal
> +		 * inverter on this board, it should be active-high. Let's fix that
> +		 * here for older DTs so we can re-use the generic nand_gpio_waitrdy()
> +		 * helper, and be consistent with what other drivers do.
> +		 */
> +		{ "qi,lb60",		"rb-gpios",	true },
>  #endif
>  	};
>  	unsigned int i;
> diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c b/drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c
> index 6748226b8bd1..c816dc137245 100644
> --- a/drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c
> +++ b/drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c
> @@ -380,18 +380,6 @@ static int ingenic_nand_init_chip(struct platform_device *pdev,
>  		return ret;
>  	}
>  
> -	/*
> -	 * The rb-gpios semantics was undocumented and qi,lb60 (along with
> -	 * the ingenic driver) got it wrong. The active state encodes the
> -	 * NAND ready state, which is high level. Since there's no signal
> -	 * inverter on this board, it should be active-high. Let's fix that
> -	 * here for older DTs so we can re-use the generic nand_gpio_waitrdy()
> -	 * helper, and be consistent with what other drivers do.
> -	 */
> -	if (of_machine_is_compatible("qi,lb60") &&
> -	    gpiod_is_active_low(nand->busy_gpio))
> -		gpiod_toggle_active_low(nand->busy_gpio);
> -
>  	nand->wp_gpio = devm_gpiod_get_optional(dev, "wp", GPIOD_OUT_LOW);
>  
>  	if (IS_ERR(nand->wp_gpio)) {
> -- 
> 2.39.2
> 

-- 
With Best Regards,
Andy Shevchenko