[PATCH 2/6] dt-bindings: mtd: Rewrite gpio-control-nand in schema
Linus Walleij
linus.walleij at linaro.org
Wed Nov 8 06:33:50 PST 2023
This creates a schema for GPIO controlled NAND. The txt
schema was old and wrong.
Mark the old way of passing GPIOs in a long array as
deprecated and encourage per-pin GPIO assignments with
the named nnn-gpios phandles.
I was unable to re-use raw-nand-chip.yaml or even
nand-chip.yaml: the reason is that they both assume
that we have potentially several NAND chips with chip
selects and thus enforce a node name "nand at 0" etc,
which doesn't quite work for this device.
Since the GPIO controlled NAND is both a NAND controller
and a NAND chip jitted together, I have to modify the
mtd.yaml nodename requirement to include nand-controller@
as this is the nodename that this device should use.
Deprecate the custom "band-width" property in favor of
"nand-bus-width".
Reported-by: Howard Harte <hharte at magicandroidapps.com>
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
Check the required section especially. Since there is no
hardware default for anything when using GPIOs for this,
I think all these parameters are compulsory.
---
.../devicetree/bindings/mtd/gpio-control-nand.txt | 47 ------
.../devicetree/bindings/mtd/gpio-control-nand.yaml | 168 +++++++++++++++++++++
Documentation/devicetree/bindings/mtd/mtd.yaml | 2 +-
3 files changed, 169 insertions(+), 48 deletions(-)
diff --git a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt
deleted file mode 100644
index 486a17d533d7..000000000000
--- a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt
+++ /dev/null
@@ -1,47 +0,0 @@
-GPIO assisted NAND flash
-
-The GPIO assisted NAND flash uses a memory mapped interface to
-read/write the NAND commands and data and GPIO pins for the control
-signals.
-
-Required properties:
-- compatible : "gpio-control-nand"
-- reg : should specify localbus chip select and size used for the chip. The
- resource describes the data bus connected to the NAND flash and all accesses
- are made in native endianness.
-- #address-cells, #size-cells : Must be present if the device has sub-nodes
- representing partitions.
-- gpios : Specifies the GPIO pins to control the NAND device. The order of
- GPIO references is: RDY, nCE, ALE, CLE, and nWP. nCE and nWP are optional.
-
-Optional properties:
-- bank-width : Width (in bytes) of the device. If not present, the width
- defaults to 1 byte.
-- chip-delay : chip dependent delay for transferring data from array to
- read registers (tR). If not present then a default of 20us is used.
-- gpio-control-nand,io-sync-reg : A 64-bit physical address for a read
- location used to guard against bus reordering with regards to accesses to
- the GPIO's and the NAND flash data bus. If present, then after changing
- GPIO state and before and after command byte writes, this register will be
- read to ensure that the GPIO accesses have completed.
-
-The device tree may optionally contain sub-nodes describing partitions of the
-address space. See partition.txt for more detail.
-
-Examples:
-
-gpio-nand at 1,0 {
- compatible = "gpio-control-nand";
- reg = <1 0x0000 0x2>;
- #address-cells = <1>;
- #size-cells = <1>;
- gpios = <&banka 1 0>, /* RDY */
- <0>, /* nCE */
- <&banka 3 0>, /* ALE */
- <&banka 4 0>, /* CLE */
- <0>; /* nWP */
-
- partition at 0 {
- ...
- };
-};
diff --git a/Documentation/devicetree/bindings/mtd/gpio-control-nand.yaml b/Documentation/devicetree/bindings/mtd/gpio-control-nand.yaml
new file mode 100644
index 000000000000..5b30ee7ad4a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/gpio-control-nand.yaml
@@ -0,0 +1,168 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/gpio-control-nand.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NAND memory exclusively connected to GPIO lines
+
+maintainers:
+ - Linus Walleij <linus.walleij at linaro.org>
+
+description: |
+ It is possible to connect a NAND flash memory without any
+ dedicated NAND controller hardware, using just general purpose
+ I/O (GPIO) pins. This will not be fast, but it will work.
+ The address and data lines of the chip will still need to be
+ connected so that the contents of a NAND page can be
+ memory-mapped and accessed after the special lines are toggled
+ by GPIO.
+
+# The GPIO controlled NAND has wires going directly to one single
+# NAND chip, so it is both a nand controller and a nand chip at
+# the same time, but it does not have things such as chip select
+# since the use is hammered down to one single chip only.
+# There is no point for the chip itself to be a subnode of the
+# controller so the raw NAND chip properties are added right into
+# the controller node like this.
+
+allOf:
+ - $ref: mtd.yaml#
+
+properties:
+ $nodename:
+ pattern: "^(nand|nand-controller)@[a-f0-9]+$"
+
+ compatible:
+ const: gpio-control-nand
+
+ reg:
+ description: |
+ This should specify the address where the NAND page currently
+ accessed gets memory-mapped, and the size of the page. Usually
+ this will be the same as the page size of the NAND.
+
+ label: true
+
+ partitions: true
+
+ nand-ecc-algo: true
+
+ nand-ecc-step-size: true
+
+ nand-ecc-strength: true
+
+ nand-use-soft-ecc-engine: true
+
+ gpio-control-nand,io-sync-reg:
+ description: |
+ A 64-bit physical address for a read location used to guard
+ against bus reordering with regards to accesses to the GPIOs and
+ the NAND flash data bus. If present, then after changing GPIO state
+ and before and after command byte writes, this register will be
+ read to ensure that the GPIO accesses have completed.
+ $ref: /schemas/types.yaml#/definitions/uint64
+
+ gpios:
+ description:
+ Legacy GPIO array for the NAND chip lines, order RDY,
+ NCE, ALE, CLE, NWP.
+ deprecated: true
+ maxItems: 5
+
+ rdy-gpios:
+ description:
+ GPIO for the NAND chip RDY line
+ maxItems: 1
+
+ ce-gpios:
+ description:
+ GPIO for the NAND chip CE chip enable line, usually
+ this is active low, so it should be tagged with the GPIO
+ flag GPIO_ACTIVE_LOW.
+ maxItems: 1
+
+ ale-gpios:
+ description:
+ GPIO for the NAND chip ALE line
+ maxItems: 1
+
+ cle-gpios:
+ description:
+ GPIO for the NAND chip CLE line
+ maxItems: 1
+
+ wp-gpios:
+ description:
+ GPIO for the NAND chip WP line, usually this is
+ active low, so it should be tagged with the GPIO
+ flag GPIO_ACTIVE_LOW.
+ maxItems: 1
+
+ bank-width:
+ description:
+ Width (in bytes) of the device. If not present, the
+ width defaults to 1 byte. This is deprecated, use
+ nand-bus-width instead.
+ deprecated: true
+ enum: [ 1, 2 ]
+ default: 1
+
+ nand-bus-width:
+ description:
+ Bus width to the NAND chip
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [8, 16]
+ default: 8
+
+ chip-delay:
+ description:
+ chip dependent delay for transferring data from array to
+ read registers (tR). If not present then a default of 20us
+ is used.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+required:
+ - compatible
+ - reg
+ - ale-gpios
+ - cle-gpios
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ nand at 20200000 {
+ compatible = "gpio-control-nand";
+ /* 512 bytes memory window at 0x20200000 */
+ reg = <0x20200000 0x200>;
+ rdy-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ ce-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+ ale-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+ cle-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+
+ label = "ixp400 NAND";
+
+ nand-use-soft-ecc-engine;
+ nand-ecc-algo = "bch";
+ nand-ecc-step-size = <512>;
+ nand-ecc-strength = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ fs at 0 {
+ label = "SysA Kernel";
+ reg = <0x0 0x400000>;
+ };
+
+ fs at 400000 {
+ label = "SysA Code";
+ reg = <0x400000 0x7C00000>;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/mtd/mtd.yaml b/Documentation/devicetree/bindings/mtd/mtd.yaml
index f322290ee516..e6fd82cbc35d 100644
--- a/Documentation/devicetree/bindings/mtd/mtd.yaml
+++ b/Documentation/devicetree/bindings/mtd/mtd.yaml
@@ -12,7 +12,7 @@ maintainers:
properties:
$nodename:
- pattern: "^(flash|.*sram|nand)(@.*)?$"
+ pattern: "^(flash|.*sram|nand|nand-controller)(@.*)?$"
label:
description:
--
2.34.1
More information about the linux-mtd
mailing list