[PATCH v1 1/2] dt-bindings: mtd: nand-controller: add nand-skip-bbtscan and nand-no-bbm-quirk DT options

[Johan Jonker]

On 7/18/23 17:46, Conor Dooley wrote:
> On Sat, Jul 15, 2023 at 12:48:16PM +0200, Johan Jonker wrote:
>> A NAND chip can contain a different data format then the MTD framework
>> expects in the erase blocks for the Bad Block Table(BBT).
>> Result is a failed probe, while nothing wrong with the hardware.
>> Some MTD flags need to be set to gain access again.
>>
>> Skip the automatic BBT scan with the NAND_SKIP_BBTSCAN option
>> so that the original content is unchanged during the driver probe.
>> The NAND_NO_BBM_QUIRK option allows us to erase bad blocks with
>> the nand_erase_nand() function and the flash_erase command.
>>
>> Add nand-skip-bbtscan and nand-no-bbm-quirk Device Tree options,
>> so the user has the "freedom of choice" by neutral
>> access mode to read and write in whatever format is needed.
>>
>> Signed-off-by: Johan Jonker <jbx6244 at gmail.com>
>> ---
>>
>> Previous discussion:
>> [PATCH v3 3/3] mtd: rawnand: rockchip-nand-controller: add skipbbt option
>> https://lore.kernel.org/linux-mtd/1618382560.2326931.1689261435022.JavaMail.zimbra@nod.at/
>> ---
>>  .../devicetree/bindings/mtd/nand-controller.yaml    | 13 +++++++++++++
>>  1 file changed, 13 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
>> index f70a32d2d9d4..ca04d06a0377 100644
>> --- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml
>> +++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
>> @@ -103,6 +103,19 @@ patternProperties:
>>            the boot ROM or similar restrictions.
>>          $ref: /schemas/types.yaml#/definitions/flag
>>
>> +      nand-no-bbm-quirk:
>> +        description:
>> +          Some controllers with pipelined ECC engines override the BBM marker with
>> +          data or ECC bytes, thus making bad block detection through bad block marker
>> +          impossible. Let's flag those chips so the core knows it shouldn't check the
>> +          BBM and consider all blocks good.
>> +        $ref: /schemas/types.yaml#/definitions/flag
> 
> While this seems okay, as it seems to describe facet of the hardware...
> 
>> +      nand-skip-bbtscan:
>> +        description:
>> +          This option skips the BBT scan during initialization.
>> +        $ref: /schemas/types.yaml#/definitions/flag
> 
> ...this seems to be used to control the behaviour of software, and does
> not describe the underlying hardware.
> 
> Maybe I'm off, but the description of the property does not hint at the
> aspect of the hardware that this addresses.

Hi Conor,


Thank you!
Your point is correct.
However I need both flags to change MTD software driver probe behavior in case of formatting.

Patch was made after comment by  Miquel:
'I would rather prefer a DT property which says "do not use the
standard pattern".'

DT should describe hardware and not software probe configuration.
Currently not aware what other options we have for module parameters.
Prefer my solution in the link. Could the MTD maintainer have a look again? Thanks!
Please advise.

Johan Jonker

> 
> Thanks,
> Conor.
> 
>> +
>>        nand-rb:
>>          description:
>>            Contains the native Ready/Busy IDs.
>> --
>> 2.30.2
>>