[PATCH v3 2/2] mtd: rawnand: meson: waiting w/o wired ready/busy pin

Arseniy Krasnov avkrasnov at sberdevices.ru
Tue Jul 4 10:32:13 PDT 2023



On 04.07.2023 16:07, Arseniy Krasnov wrote:
> 
> 
> On 04.07.2023 16:12, Miquel Raynal wrote:
>> Hi Arseniy,
>>
>> avkrasnov at sberdevices.ru wrote on Tue, 4 Jul 2023 15:46:18 +0300:
>>
>>> On 04.07.2023 15:43, Miquel Raynal wrote:
>>>> Hi Arseniy,
>>>>
>>>> AVKrasnov at sberdevices.ru wrote on Thu, 8 Jun 2023 07:47:28 +0300:
>>>>   
>>>>> If there is no wired ready/busy pin, classic way to wait for command
>>>>> completion is to use function 'nand_soft_waitrdy()'. Meson NAND has
>>>>> special command which allows to wait for NAND_STATUS_READY bit without
>>>>> reading status in a software loop (as 'nand_soft_waitrdy()' does). To
>>>>> use it send this command along with NAND_CMD_STATUS, then wait for an
>>>>> interrupt, and after interrupt send NAND_CMD_READ0. So this feature
>>>>> allows to use interrupt driven waiting without wired ready/busy pin.
>>>>>
>>>>> Suggested-by: Liang Yang <liang.yang at amlogic.com>
>>>>> Signed-off-by: Arseniy Krasnov <AVKrasnov at sberdevices.ru>
>>>>> ---
>>>>>  drivers/mtd/nand/raw/meson_nand.c | 77 +++++++++++++++++++++++++++++--
>>>>>  1 file changed, 73 insertions(+), 4 deletions(-)
>>>>>
>>>>> diff --git a/drivers/mtd/nand/raw/meson_nand.c b/drivers/mtd/nand/raw/meson_nand.c
>>>>> index 074e14225c06..9f05e113b4ea 100644
>>>>> --- a/drivers/mtd/nand/raw/meson_nand.c
>>>>> +++ b/drivers/mtd/nand/raw/meson_nand.c
>>>>> @@ -38,6 +38,7 @@
>>>>>  #define NFC_CMD_SCRAMBLER_DISABLE	0
>>>>>  #define NFC_CMD_SHORTMODE_DISABLE	0
>>>>>  #define NFC_CMD_RB_INT		BIT(14)
>>>>> +#define NFC_CMD_RB_INT_NO_PIN	((0xb << 10) | BIT(18) | BIT(16))
>>>>>  
>>>>>  #define NFC_CMD_GET_SIZE(x)	(((x) >> 22) & GENMASK(4, 0))
>>>>>  
>>>>> @@ -179,6 +180,7 @@ struct meson_nfc {
>>>>>  	u32 info_bytes;
>>>>>  
>>>>>  	unsigned long assigned_cs;
>>>>> +	bool no_rb_pin;
>>>>>  };
>>>>>  
>>>>>  enum {
>>>>> @@ -392,7 +394,42 @@ static void meson_nfc_set_data_oob(struct nand_chip *nand,
>>>>>  	}
>>>>>  }
>>>>>  
>>>>> -static int meson_nfc_queue_rb(struct meson_nfc *nfc, int timeout_ms)
>>>>> +static int meson_nfc_wait_no_rb_pin(struct meson_nfc *nfc, int timeout_ms,
>>>>> +				    bool need_cmd_read0)
>>>>> +{
>>>>> +	u32 cmd, cfg;
>>>>> +
>>>>> +	meson_nfc_cmd_idle(nfc, nfc->timing.twb);
>>>>> +	meson_nfc_drain_cmd(nfc);
>>>>> +	meson_nfc_wait_cmd_finish(nfc, CMD_FIFO_EMPTY_TIMEOUT);
>>>>> +
>>>>> +	cfg = readl(nfc->reg_base + NFC_REG_CFG);
>>>>> +	cfg |= NFC_RB_IRQ_EN;
>>>>> +	writel(cfg, nfc->reg_base + NFC_REG_CFG);
>>>>> +
>>>>> +	reinit_completion(&nfc->completion);
>>>>> +	cmd = nfc->param.chip_select | NFC_CMD_CLE | NAND_CMD_STATUS;
>>>>> +	writel(cmd, nfc->reg_base + NFC_REG_CMD);
>>>>> +
>>>>> +	/* use the max erase time as the maximum clock for waiting R/B */
>>>>> +	cmd = NFC_CMD_RB | NFC_CMD_RB_INT_NO_PIN | nfc->timing.tbers_max;
>>>>> +	writel(cmd, nfc->reg_base + NFC_REG_CMD);
>>>>> +
>>>>> +	if (!wait_for_completion_timeout(&nfc->completion,
>>>>> +					 msecs_to_jiffies(timeout_ms)))
>>>>> +		return -ETIMEDOUT;
>>>>> +
>>>>> +	if (need_cmd_read0) {
>>>>> +		cmd = nfc->param.chip_select | NFC_CMD_CLE | NAND_CMD_READ0;
>>>>> +		writel(cmd, nfc->reg_base + NFC_REG_CMD);
>>>>> +		meson_nfc_drain_cmd(nfc);
>>>>> +		meson_nfc_wait_cmd_finish(nfc, CMD_FIFO_EMPTY_TIMEOUT);
>>>>> +	}  
>>>>
>>>> I forgot about this, you should avoid open coding core helpers, can you
>>>> please send a followup patch to use nand_status_op() and
>>>> nand_exit_status_op() ?  
>>>
>>> A ok, so:
>>> 1) Sending NAND_CMD_STATUS goes to nand_status_op()
>>> 2) Sending NAND_CMD_READ0 goes to nand_exit_status_op()
>>>
>>> Ok, no problem! I'll prepare and send it on this week!
>>
>> Exactly. Sorry I had this in mind but I likely forgot to write it
>> down.
> 
> Ok, got it!

Hm, seems 'int nand_exit_status_op(struct nand_chip *chip)' is not exported,
so I can't use it in the Meson module. While 'nand_status_op()' works ok.
May I can export 'nand_exit_status_op()?'

Thanks, Arseniy


> 
> Thanks, Arseniy
> 
>>
>> Thanks,
>> Miquèl



More information about the linux-mtd mailing list