[PATCH V7 7/7] spi: spi-zynqmp-gqspi: Add parallel memories support in GQSPI driver

[Amit Kumar Mahapatra]

During probe GQSPI driver sets SPI_CONTROLLER_MULTI_CS bit in ctlr->flags
for notifying SPI core about multi CS capability of the controller.
In parallel mode the controller can either split the data between both the
flash or can send the same data to both the flashes, this is determined by
the STRIPE bit. While sending commands to the flashes the GQSPI driver
send the same command to both the flashes by resetting the STRIPE bit, but
while writing/reading data to & from the flash the GQSPI driver splits the
data evenly between both the flashes by setting the STRIPE bit.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra at amd.com>
---
 drivers/spi/spi-zynqmp-gqspi.c | 39 +++++++++++++++++++++++++++++++++-
 1 file changed, 38 insertions(+), 1 deletion(-)

diff --git a/drivers/spi/spi-zynqmp-gqspi.c b/drivers/spi/spi-zynqmp-gqspi.c
index 3d2b92a88e8a..2b2b5c0385fc 100644
--- a/drivers/spi/spi-zynqmp-gqspi.c
+++ b/drivers/spi/spi-zynqmp-gqspi.c
@@ -23,6 +23,7 @@
 #include <linux/spinlock.h>
 #include <linux/workqueue.h>
 #include <linux/spi/spi-mem.h>
+#include <linux/mtd/spi-nor.h>
 
 /* Generic QSPI register offsets */
 #define GQSPI_CONFIG_OFST		0x00000100
@@ -192,6 +193,7 @@ struct qspi_platform_data {
  * @op_lock:		Operational lock
  * @speed_hz:          Current SPI bus clock speed in hz
  * @has_tapdelay:	Used for tapdelay register available in qspi
+ * @is_parallel:		Used for multi CS support
  */
 struct zynqmp_qspi {
 	struct spi_controller *ctlr;
@@ -214,8 +216,33 @@ struct zynqmp_qspi {
 	struct mutex op_lock;
 	u32 speed_hz;
 	bool has_tapdelay;
+	bool is_parallel;
 };
 
+/**
+ * zynqmp_gqspi_update_stripe - For GQSPI controller data stripe capabilities
+ * @op:	Pointer to mem ops
+ * Return:      Status of the data stripe
+ *
+ * Returns true if data stripe need to be enabled, else returns false
+ */
+bool zynqmp_gqspi_update_stripe(const struct spi_mem_op *op)
+{
+	if (op->cmd.opcode ==  SPINOR_OP_BE_4K ||
+	    op->cmd.opcode ==  SPINOR_OP_BE_32K ||
+	    op->cmd.opcode ==  SPINOR_OP_CHIP_ERASE ||
+	    op->cmd.opcode ==  SPINOR_OP_SE ||
+	    op->cmd.opcode ==  SPINOR_OP_BE_32K_4B ||
+	    op->cmd.opcode ==  SPINOR_OP_SE_4B ||
+	    op->cmd.opcode == SPINOR_OP_BE_4K_4B ||
+	    op->cmd.opcode ==  SPINOR_OP_WRSR ||
+	    op->cmd.opcode ==  SPINOR_OP_BRWR ||
+	    (op->cmd.opcode ==  SPINOR_OP_WRSR2 && !op->addr.nbytes))
+		return false;
+
+	return true;
+}
+
 /**
  * zynqmp_gqspi_read - For GQSPI controller read operation
  * @xqspi:	Pointer to the zynqmp_qspi structure
@@ -470,7 +497,14 @@ static void zynqmp_qspi_chipselect(struct spi_device *qspi, bool is_high)
 
 	genfifoentry |= GQSPI_GENFIFO_MODE_SPI;
 
-	if (qspi->cs_index_mask & GQSPI_SELECT_UPPER_CS) {
+	if ((qspi->cs_index_mask & GQSPI_SELECT_LOWER_CS) &&
+	    (qspi->cs_index_mask & GQSPI_SELECT_UPPER_CS)) {
+		zynqmp_gqspi_selectslave(xqspi,
+					 GQSPI_SELECT_FLASH_CS_BOTH,
+					 GQSPI_SELECT_FLASH_BUS_BOTH);
+		if (!xqspi->is_parallel)
+			xqspi->is_parallel = true;
+	} else if (qspi->cs_index_mask & GQSPI_SELECT_UPPER_CS) {
 		zynqmp_gqspi_selectslave(xqspi,
 					 GQSPI_SELECT_FLASH_CS_UPPER,
 					 GQSPI_SELECT_FLASH_BUS_LOWER);
@@ -1139,6 +1173,8 @@ static int zynqmp_qspi_exec_op(struct spi_mem *mem,
 	}
 
 	if (op->data.nbytes) {
+		if (xqspi->is_parallel && zynqmp_gqspi_update_stripe(op))
+			genfifoentry |= GQSPI_GENFIFO_STRIPE;
 		reinit_completion(&xqspi->data_completion);
 		if (op->data.dir == SPI_MEM_DATA_OUT) {
 			xqspi->txbuf = (u8 *)op->data.buf.out;
@@ -1334,6 +1370,7 @@ static int zynqmp_qspi_probe(struct platform_device *pdev)
 	ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
 	ctlr->dev.of_node = np;
 	ctlr->auto_runtime_pm = true;
+	ctlr->flags |= SPI_CONTROLLER_MULTI_CS;
 
 	ret = devm_spi_register_controller(&pdev->dev, ctlr);
 	if (ret) {
-- 
2.17.1