[PATCH v4 1/2] dt-bindings: mtd: marvell-nand: Convert to YAML DT scheme

[Vadym Kochan]

On Tue, 25 Oct 2022 09:51:14 -0400, Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org> wrote:
> On 25/10/2022 08:52, Vadym Kochan wrote:
> > On Tue, 25 Oct 2022 08:25:01 -0400, Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org> wrote:
> >> On 25/10/2022 06:17, Vadym Kochan wrote:
> >>> Switch the DT binding to a YAML schema to enable the DT validation.
> >>>
> >>> Dropped deprecated compatibles and properties described in txt file.
> >>>
> >>> Signed-off-by: Vadym Kochan <vadym.kochan at plvision.eu>
> >>> ---
> >>>
> >>> v4:
> >>>    1) Remove "label" and "partitions" properties
> >>
> >> I think you did not read the feedback.
> >>
> >>
> >> (...)
> >>
> >>> +
> >>> +  marvell,system-controller:
> >>> +    $ref: /schemas/types.yaml#/definitions/phandle
> >>> +    description: Syscon node that handles NAND controller related registers
> >>> +
> >>> +patternProperties:
> >>> +  "^nand@[0-3]$":
> >>> +    type: object
> >>> +    properties:
> >>> +      reg:
> >>> +        minimum: 0
> >>> +        maximum: 3
> >>> +
> >>> +      nand-rb:
> >>> +        minimum: 0
> >>> +        maximum: 1
> >>> +
> >>> +      nand-ecc-strength:
> >>> +        enum: [1, 4, 8]
> >>> +
> >>> +      nand-on-flash-bbt: true
> >>> +
> >>> +      nand-ecc-mode: true
> >>> +
> >>> +      nand-ecc-algo:
> >>> +        description: |
> >>> +          This property is essentially useful when not using hardware ECC.
> >>> +          Howerver, it may be added when using hardware ECC for clarification
> >>> +          but will be ignored by the driver because ECC mode is chosen depending
> >>> +          on the page size and the strength required by the NAND chip.
> >>> +          This value may be overwritten with nand-ecc-strength property.
> >>> +
> >>> +      nand-ecc-step-size:
> >>> +        description: |
> >>> +          Marvell's NAND flash controller does use fixed strength
> >>> +          (1-bit for Hamming, 16-bit for BCH), so the actual step size
> >>> +          will shrink or grow in order to fit the required strength.
> >>> +          Step sizes are not completely random for all and follow certain
> >>> +          patterns described in AN-379, "Marvell SoC NFC ECC".
> >>> +
> >>> +      marvell,nand-keep-config:
> >>> +        description: |
> >>> +          Orders the driver not to take the timings from the core and
> >>> +          leaving them completely untouched. Bootloader timings will then
> >>> +          be used.
> >>> +        $ref: /schemas/types.yaml#/definitions/flag
> >>> +
> >>> +      marvell,nand-enable-arbiter:
> >>> +        description: |
> >>> +          To enable the arbiter, all boards blindly used it,
> >>> +          this bit was set by the bootloader for many boards and even if
> >>> +          it is marked reserved in several datasheets, it might be needed to set
> >>> +          it (otherwise it is harmless) so whether or not this property is set,
> >>> +          the bit is selected by the driver.
> >>> +        $ref: /schemas/types.yaml#/definitions/flag
> >>> +        deprecated: true
> >>> +
> >>> +    required:
> >>> +      - reg
> >>> +      - nand-rb
> >>
> >> I have no clue why you are doing some random changes. Now you dropped
> >> additionalProperties for nand@ about which no one asked you to drop.
> >>
> >> No. It *must* be here.
> > 
> > Sorry for this mess, I was confused with the "label" and "partitions"
> > because I got errors about these properties when I used only
> > "additionalProperties: false", so I tried to put reference to partition.yaml.
> > 
> > Then I looked at other nand-controllers schemas and I did not find inclusion of partition.yaml
> > for them so I decided to just drop it at all. My understanding is that "additionalProperties:false"
> > is needed for nand@ if to have "label" and "partitions" properties, otherwise it is not needed.
> 
> A final schema (not used by other schemas) must always finish with
> additional/unevaluatedProperties false. You have errors since beginning
> - I wrote about it in your first patchset (v1). You had error visible
> after adding proper unevaluatedProperties in proper place.
> 
> You have partitions node, for partitions. But you reference only *one*
> partition.

Yes, sorry for that.

OK, I think I need to do this in nand@:

      ...
            
      label:
        $ref: /schemas/types.yaml#/definitions/string

      partitions:
        type: object

      ...
      
    additionalProperties: false

So the "partitions" will be validated for example by fixed-partitions.yaml.
And additionalProperties:false in the nand@ protects from adding other
non-valid properties on it's hierarchy level since all possible
properties in nand@ are covered.

> 
> Best regards,
> Krzysztof
>