[RFC v2 2/2] arm: hisi: enable Hi3521a soc
Krzysztof Kozlowski
krzysztof.kozlowski at linaro.org
Tue May 3 04:47:01 PDT 2022
On 01/05/2022 19:34, Marty E. Plummer wrote:
> Enable Hisilicon Hi3521A/Hi3520DCV300 SoC. This SoC series includes
> hardware mutlimedia codec cores, commonly used in consumer cctv/dvr
> security systems and ipcameras. The arm core is a Cortex A7.
>
> Add hi3521a.dtsi and hi3521a-rs-dm290e.dts for RaySharp CCTV systems,
> marketed under the name Samsung SDR-B74301N.
Thank you for your patch. There is something to discuss/improve.
>
> Signed-off-by: Marty E. Plummer <hanetzer at startmail.com>
> ---
> arch/arm/boot/dts/Makefile | 2 +
> arch/arm/boot/dts/hi3521a-rs-dm290e.dts | 134 ++++++++
> arch/arm/boot/dts/hi3521a.dtsi | 423 ++++++++++++++++++++++++
DTSes go to separate patches.
> arch/arm/mach-hisi/Kconfig | 9 +
> 4 files changed, 568 insertions(+)
> create mode 100644 arch/arm/boot/dts/hi3521a-rs-dm290e.dts
> create mode 100644 arch/arm/boot/dts/hi3521a.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7c16f8a2b738..535cef3b14ab 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -242,6 +242,8 @@ dtb-$(CONFIG_ARCH_GEMINI) += \
> gemini-ssi1328.dtb \
> gemini-wbd111.dtb \
> gemini-wbd222.dtb
> +dtb-$(CONFIG_ARCH_HI3521A) += \
> + hi3521a-rs-dm290e.dtb
> dtb-$(CONFIG_ARCH_HI3xxx) += \
> hi3620-hi4511.dtb
> dtb-$(CONFIG_ARCH_HIGHBANK) += \
> diff --git a/arch/arm/boot/dts/hi3521a-rs-dm290e.dts b/arch/arm/boot/dts/hi3521a-rs-dm290e.dts
> new file mode 100644
> index 000000000000..b24fcf2ca85e
> --- /dev/null
> +++ b/arch/arm/boot/dts/hi3521a-rs-dm290e.dts
> @@ -0,0 +1,134 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Copyright (C) 2017-2022 Marty Plummer <hanetzer at startmail.com>
> + */
> +
> +#include "hi3521a.dtsi"
> +
> +/ {
> + model = "RaySharp RS-DM-290E DVR Board";
> + compatible = "raysharp,rs-dm-290e", "hisilicon,hi3521a";
Please run checkpatch and fix the warnings.
> +
> + aliases {
> + serial0 = &uart0;
> + serial1 = &uart1;
> + serial2 = &uart2;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory at 800000000 {
> + device_type = "memory";
> + reg = <0x80000000 0xf00000>;
> + };
> +};
> +
> +&hi_sfc {
> + status = "okay";
> + spi-nor at 0 {
Looks like wrong node name. You need to run "dtbs_check" and fix
warnings related to your DTS.
> + // compatible = "jedec,spi-nor";
No dead code in Linux kernel. Commented out stuff sometimes is okay if
it is explained with comments.
> + compatible = "macronix,mx25l25635e", "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <150000000>;
> + // spi-rx-bus-width = <1>;
> + // spi-tx-bus-width = <1>;
> + // m25p,default-addr-width = <4>;
> + // spi-max-frequency = <160000000>;
No dead code.
> + m25p,fast-read;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + u-boot at 0 {
> + label = "u-boot";
> + reg = <0x0 0x50000>;
> + read-only;
> + };
> + u-boot-env at 50000 {
> + label = "u-boot-env";
> + reg = <0x50000 0x20000>;
> + };
> + kernel at 70000 {
> + label = "kernel";
> + reg = <0x70000 0x700000>;
> + };
> + rootfs at 770000 {
> + label = "rootfs";
> + reg = <0x800000 0x300000>;
> + read-only;
> + };
> + extra at b00000 {
> + label = "extra";
> + reg = <0xb00000 0x1500000>;
> + };
> + };
> + };
> +};
> +
> +&dual_timer0 {
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pmx_func &uart0_cfg_func>;
> + status = "okay";
> +};
> +
> +&pmx0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&sfc_pmx_func>;
> + uart0_pmx_func: uart0_pmx_func {
> + pinctrl-single,pins = <
> + 0x00e8 0x0
> + 0x00ec 0x0
> + >;
> + };
> +
> + sfc_pmx_func: sfc_pmx_func {
> + pinctrl-single,pins = <
> + 0x00c4 0x1
> + 0x00c8 0x1
> + 0x00cc 0x1
> + 0x00d0 0x1
> + 0x00d4 0x1
> + >;
> + };
> +};
> +
> +&pmx1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&sfc_cfg_func>;
> + uart0_cfg_func: uart0_cfg_func {
> + pinctrl-single,pins = <
> + 0x00e8 0x0
> + 0x00ec 0x0
> + >;
> + };
Blank line
> + sfc_cfg_func: sfc_cfg_func {
> + pinctrl-single,pins = <
> + 0x00c4 0x58
> + 0x00c8 0x28
> + 0x00cc 0x38
> + 0x00d0 0x38
> + 0x00d4 0x38
> + >;
> + };
> +};
> +
> +/* &gmac0 { */
> +/* #address-cells = <1>; */
> +/* #size-cells = <0>; */
> +/* phy-handle = <&phy3>; */
> +/* phy-mode = "rgmii"; */
> +/* mac-address = [00 00 00 00 00 00]; */
> +/* status = "okay"; */
> +/**/
> +/* phy3: ethernet-phy at 3 { */
> +/* reg = <3>; */
> +/* }; */
> +/* }; */
? What's this?
> diff --git a/arch/arm/boot/dts/hi3521a.dtsi b/arch/arm/boot/dts/hi3521a.dtsi
> new file mode 100644
> index 000000000000..53993a32fd5d
> --- /dev/null
> +++ b/arch/arm/boot/dts/hi3521a.dtsi
> @@ -0,0 +1,423 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Copyright (C) 2017-2022 Marty Plummer <hanetzer at startmail.com>
> + */
> +
> +#include <dt-bindings/clock/hi3521a-clock.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +/dts-v1/;
Blank line.
> +/ {
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu0: cpu at 0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a7";
> + reg = <0>;
> + clock-frequency = <1100000000>;
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv7-timer";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 13 0xf08>,
> + <GIC_PPI 14 0xf08>,
> + <GIC_PPI 11 0xf08>,
> + <GIC_PPI 10 0xf08>;
Use macros for these interrupts.
> + clock-frequency = <24000000>;
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a7-pmu";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gic: interrupt-controller at 10301000 {
> + compatible = "arm,pl390";
> + #interrupt-cells = <3>;
> + interrupt-controller;
> + reg = <0x10301000 0x1000>, <0x10302000 0x1000>;
Put reg just after compatible. This applies to each other node as well
(if it comes with reg).
> + };
> +
> + xtal24m: xtal24m {
Generic node names, so one of: "clock-0" "clock-xtal24m"
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <24000000>;
This does not look like property of the SoC, so should be defined by boards.
> + };
> +
> + clk_3m: clk_3m {
No underscores in node names, generic node name (see above).
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <3000000>;
This does not look like property of the SoC, so should be defined by boards.
> + };
> +
> + soc {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "simple-bus";
> + interrupt-parent = <&gic>;
> + ranges;
> +
> + hi_sfc: spi at 10000000 {
> + compatible = "hisilicon,hi3521a-spi-nor", "hisilicon,fmc-spi-nor";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x10000000 0x1000>, <0x14000000 0x10000>;
> + reg-names = "control", "memory";
> + clocks = <&crg HI3521A_FMC_CLK>;
> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + /* usb0: usb at 10030000 { */
> + /* compatible = "generic-ohci"; */
> + /* reg = <0x10030000 0x1000>; */
> + /* interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; */
> + /* clocks = <&crg > */
> + /* }; */
No dead code please.
> + dmac: dma-controller at 10060000 {
> + compatible = "arm,pl080", "arm,primecell";
> + arm,primecell-periphid = <0x00041080>;
> + reg = <0x10060000 0x1000>;
> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&crg HI3521A_DMAC_CLK>;
> + clock-names = "apb_pclk";
> + lli-bus-interface-ahb1;
> + lli-bus-interface-ahb2;
> + mem-bus-interface-ahb1;
> + mem-bus-interface-ahb2;
> + memcpy-burst-size = <256>;
> + memcpy-bus-width = <32>;
> + #dma-cells = <2>;
> + status = "okay";
No need for status okay, it's by default.
> + };
> +
> + gmac0: ethernet at 100a0000 {
> + compatible = "hisilicon,hisi-gmac-v1";
> + reg = <0x100a0000 0x1000>, <0x1204008c 0x4>;
> + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&crg HI3521A_ETH_CLK>, <&crg HI3521A_ETH_MACIF_CLK>;
> + clock-names = "mac_core", "mac_ifc";
> + /* resets = <&crg 0x78 0>, <&crg 0x78 2>, <&crg 0x78 5>; */
> + /* reset-names = "mac_core", "mac_ifc", "phy"; */
> + /* hisilicon,phy-reset-delays-us = <10000 10000 30000>; */
No dead code.
> + status = "disabled";
> + };
> +
> + dual_timer0: timer at 12000000 {
> + compatible = "arm,sp804", "arm,primecell";
> + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
A bit weird interrupts... the same?
> + reg = <0x12000000 0x1000>;
> + clocks = <&sysctrl HI3521A_TIMER0_CLK>,
> + <&sysctrl HI3521A_TIMER1_CLK>,
> + <&crg HI3521A_APB_CLK>;
> + clock-names = "timer0clk", "timer1clk", "apb_pclk";
> + status = "disabled";
> + };
> +
> + dual_timer1: timer at 12010000 {
> + compatible = "arm,sp804", "arm,primecell";
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x12010000 0x1000>;
> + clocks = <&sysctrl HI3521A_TIMER2_CLK>,
> + <&sysctrl HI3521A_TIMER3_CLK>,
> + <&crg HI3521A_APB_CLK>;
> + clock-names = "timer0clk", "timer1clk", "apb_pclk";
> + status = "disabled";
> + };
> +
> + dual_timer2: timer at 12020000 {
> + compatible = "arm,sp804", "arm,primecell";
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x12020000 0x1000>;
> + clocks = <&sysctrl HI3521A_TIMER4_CLK>,
> + <&sysctrl HI3521A_TIMER5_CLK>,
> + <&crg HI3521A_APB_CLK>;
> + clock-names = "timer0clk", "timer1clk", "apb_pclk";
> + status = "disabled";
> + };
> +
> + dual_timer3: timer at 12030000 {
> + compatible = "arm,sp804", "arm,primecell";
> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x12030000 0x1000>;
> + clocks = <&sysctrl HI3521A_TIMER6_CLK>,
> + <&sysctrl HI3521A_TIMER7_CLK>,
> + <&crg HI3521A_APB_CLK>;
> + clock-names = "timer0clk", "timer1clk", "apb_pclk";
> + status = "disabled";
> + };
> +
> + crg: clock-reset-controller at 12040000 {
> + compatible = "hisilicon,hi3521a-crg";
Undocumented compatible. Didn't checkpatch warn about it?
> + #clock-cells = <1>;
> + #reset-cells = <2>;
> + reg = <0x12040000 0x1000>;
> + };
> +
> + sysctrl: system-controller at 12050000 {
> + compatible = "hisilicon,hi3521a-sysctrl", "syscon";
Same.
> + reg = <0x12050000 0x1000>;
> + #clock-cells = <1>;
> + #reset-cells = <2>;
> + };
> +
> + reboot {
> + compatible = "syscon-reboot";
> + regmap = <&sysctrl>;
> + offset = <0x4>;
> + mask = <0xdeadbeef>;
> + };
> +
> + wdt0: watchdog at 12070000 {
> + compatible = "arm,sp805", "arm,primecell";
> + arm,primecell-periphid = <0x00141805>;
> + reg = <0x12070000 0x1000>;
> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&crg HI3521A_FIXED_3M>;
> + clock-names = "apb_pclk";
> + };
> +
> + uart0: serial at 12080000 {
> + compatible = "arm,pl011", "arm,primecell";
> + reg = <0x12080000 0x1000>;
> + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&crg HI3521A_UART0_CLK>, <&crg HI3521A_UART0_CLK>;
> + clock-names = "uartclk", "apb_pclk";
> + dmas = <&dmac 0 1>, <&dmac 1 2>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + uart1: serial at 12090000 {
> + compatible = "arm,pl011", "arm,primecell";
> + reg = <0x12090000 0x1000>;
> + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&crg HI3521A_UART1_CLK>;
> + clock-names = "apb_pclk";
> + dmas = <&dmac 2 1>, <&dmac 3 2>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + uart2: serial at 120a0000 {
> + compatible = "arm,pl011", "arm,primecell";
> + reg = <0x120a0000 0x1000>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&crg HI3521A_UART2_CLK>;
> + clock-names = "apb_pclk";
> + dmas = <&dmac 4 1>, <&dmac 5 2>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + spi_bus0: spi at 120d0000 {
> + compatible = "arm,pl022", "arm,primecell";
> + reg = <0x120d0000 0x1000>;
> + arm,primecell-periphid = <0x00041022>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&crg HI3521A_SPI0_CLK>;
> + clock-names = "apb_pclk";
> + dmas = <&dmac 6 1>, <&dmac 7 2>;
> + dma-names = "rx", "tx";
> + num-cs = <2>;
> + status = "disabled";
> + };
> +
> + pmx0: pinmux at 120f0000 {
> + compatible = "pinctrl-single";
> + reg = <0x120f0000 0x188>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + #pinctrl-cells = <1>;
> + #gpio-range-cells = <3>;
> + ranges;
> +
> + pinctrl-single,register-width = <32>;
> + pinctrl-single,function-mask = <7>;
> + /* pin base, nr pins & gpio function */
> + pinctrl-single,gpio-range = <
> + &range 58 4 0
> + >;
> +
> + range: gpio-range {
> + #pinctrl-single,gpio-range-cells = <3>;
> + };
> + };
> +
> + pmx1: pinmux at 120f0800 {
> + compatible = "pinconf-single";
> + reg = <0x120f0800 0x1d4>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + #pinctrl-cells = <1>;
> + ranges;
> +
> + pinctrl-single,register-width = <32>;
> + };
> +
> + gpio0: gpio at 12150000 {
> + compatible = "arm,pl061", "arm,primecell";
> + reg = <0x12150000 0x1000>;
> + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "disabled";
> + };
> +
> + gpio1: gpio at 12160000 {
> + compatible = "arm,pl061", "arm,primecell";
> + reg = <0x12160000 0x1000>;
> + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "disabled";
> + };
> +
> + gpio2: gpio at 12170000 {
> + compatible = "arm,pl061", "arm,primecell";
> + reg = <0x12170000 0x1000>;
> + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "disabled";
> + };
> +
> + gpio3: gpio at 12180000 {
> + compatible = "arm,pl061", "arm,primecell";
> + reg = <0x12180000 0x1000>;
> + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "disabled";
> + };
> +
> + gpio4: gpio at 12190000 {
> + compatible = "arm,pl061", "arm,primecell";
> + reg = <0x12190000 0x1000>;
> + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "disabled";
> + };
> +
> + gpio5: gpio at 121a0000 {
> + compatible = "arm,pl061", "arm,primecell";
> + reg = <0x121a0000 0x1000>;
> + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "disabled";
> + };
> +
> + gpio6: gpio at 121b0000 {
> + compatible = "arm,pl061", "arm,primecell";
> + reg = <0x121b0000 0x1000>;
> + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
Same interrupts as for other nodes? Is it correct?
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "disabled";
> + };
> +
> + gpio7: gpio at 121c0000 {
> + compatible = "arm,pl061", "arm,primecell";
> + reg = <0x121c0000 0x1000>;
> + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "disabled";
> + };
> +_MULTI_V7
Best regards,
Krzysztof
More information about the linux-mtd
mailing list