[PATCH v2 1/2] mtd: rawnand: arasan: Update NAND bus clock instead of system clock

[Miquel Raynal]

Hi Amit,

amit.kumar-mahapatra at xilinx.com wrote on Tue, 21 Jun 2022 14:24:59
+0530:

> In current implementation the Arasan NAND driver is updating the
> system clock(i.e., anand->clk) in accordance to the timing modes
> (i.e., SDR or NVDDR). But as per the Arasan NAND controller spec the
> flash clock or the NAND bus clock(i.e., nfc->bus_clk), need to be
> updated instead. This patch keeps the system clock unchanged and updates
> the NAND bus clock as per the timing modes.

This is not what you do below. If the clock that is changed is the
wrong one, then just change the clock used in the clk_set_rate call
instead of calling clk_set_rate twice at the wrong location.
->set_interface is done once per chip, if you have two different chips
on the same system you must change the clock when you switch from one
chip to the other. Your current implementation disrespects that,
unfortunately.

> 
> Fixes: 197b88fecc50 ("mtd: rawnand: arasan: Add new Arasan NAND controller")

Requires a Cc: stable tag

> Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra at xilinx.com>
> ---
>  drivers/mtd/nand/raw/arasan-nand-controller.c | 16 +++++++++++++---
>  1 file changed, 13 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/mtd/nand/raw/arasan-nand-controller.c b/drivers/mtd/nand/raw/arasan-nand-controller.c
> index 53bd10738418..4f6da82dd2b1 100644
> --- a/drivers/mtd/nand/raw/arasan-nand-controller.c
> +++ b/drivers/mtd/nand/raw/arasan-nand-controller.c
> @@ -968,6 +968,7 @@ static int anfc_setup_interface(struct nand_chip *chip, int target,
>  	const struct nand_sdr_timings *sdr;
>  	const struct nand_nvddr_timings *nvddr;
>  	unsigned int tccs_min, dqs_mode, fast_tcad;
> +	int ret;
>  
>  	if (nand_interface_is_nvddr(conf)) {
>  		nvddr = nand_get_nvddr_timings(conf);
> @@ -1043,7 +1044,11 @@ static int anfc_setup_interface(struct nand_chip *chip, int target,
>  				 DQS_BUFF_SEL_OUT(dqs_mode);
>  	}
>  
> -	anand->clk = ANFC_XLNX_SDR_DFLT_CORE_CLK;
> +	ret = clk_set_rate(nfc->bus_clk, ANFC_XLNX_SDR_DFLT_CORE_CLK);
> +	if (ret) {
> +		dev_err(nfc->dev, "Failed to change bus clock rate\n");
> +		return ret;
> +	}
>  
>  	/*
>  	 * Due to a hardware bug in the ZynqMP SoC, SDR timing modes 0-1 work
> @@ -1052,8 +1057,13 @@ static int anfc_setup_interface(struct nand_chip *chip, int target,
>  	 * 80MHz when using SDR modes 2-5 with this SoC.
>  	 */
>  	if (of_device_is_compatible(np, "xlnx,zynqmp-nand-controller") &&
> -	    nand_interface_is_sdr(conf) && conf->timings.mode >= 2)
> -		anand->clk = ANFC_XLNX_SDR_HS_CORE_CLK;
> +	    nand_interface_is_sdr(conf) && conf->timings.mode >= 2) {
> +		ret = clk_set_rate(nfc->bus_clk, ANFC_XLNX_SDR_HS_CORE_CLK);
> +		if (ret) {
> +			dev_err(nfc->dev, "Failed to change bus clock rate\n");
> +			return ret;
> +		}
> +	}
>  
>  	return 0;
>  }


Thanks,
Miquèl