[PATCH v4 0/2] Add support for unprotected spare data page

[Manivannan Sadhasivam]

On Fri, Jun 03, 2022 at 05:25:56PM +0200, Ansuel Smith wrote:
> On Fri, Jun 03, 2022 at 08:48:06PM +0530, Manivannan Sadhasivam wrote:
> > On Thu, May 19, 2022 at 09:01:10PM +0200, Ansuel Smith wrote:
> > > Some background about this.
> > > On original qsdk ipq8064 based firmware there was a big separation from
> > > boot partition and user partition. With boot partition we refer to
> > > partition used to init the router (bootloader, spm firmware and other
> > > internal stuff) With user partition we refer to linux partition and data
> > > partition not used to init the router.
> > > When someone had to write to these boot partition a special mode was
> > > needed, to switch the nand driver to this special configuration.
> > > 
> > > Upstream version of the nandc driver totally dropped this and the result
> > > is that if someone try to read data from these partition a CRC warning
> > > is printed and if someone try to write that (if for example someone
> > > wants to replace the bootloader) result is a broken system as the data
> > > is badly written.
> > > 
> > 
> > Can you please point me to the downstream/vendor driver that has this
> > implementation?
> > 
> > Thanks,
> > Mani
> >
> 
> Actually found the repo...This is the link [1].
> 
> My implementation is a variant of this since originally they used a
> sysfs entry to swap the ecc configuration.
> 
> [1] https://github.com/marxfang/ipq807x-spf100-cs/blob/master/qsdk/qca/src/linux-4.4/drivers/mtd/nand/qcom_nandc.c
> 

Thanks for the link! After talking internally to Qcom folks, I confirmed
that this quirk is only needed on IPQ8064 based platforms.

More in the driver patch...

Thanks,
Mani

> > > This series comes to fix this.
> > > 
> > > A user can declare offset and size of these special partition using the
> > > qcom,boot-pages binding.
> > > 
> > > An initial implementation of this assumed that the boot-pages started
> > > from the start of the nand but we discover that some device have backup
> > > of these special partition and we can have situation where we have this
> > > partition scheme
> > > - APPSBL (require special mode)
> > > - APPSBLENV (doesn't require special mode)
> > > - ART
> > > - APPSBLBK (back of APPSBL require special mode)
> > > - APPSBLENVBK (back of APPSBLENV doesn't require special mode)
> > > With this configuration we need to declare sparse boot page and we can't
> > > assume boot-pages always starts from the start of the nand.
> > > 
> > > A user can use this form to declare sparse boot pages
> > > qcom,boot-pages = <0x0 0x0c80000 0x0c80000 0x0500000>;
> > > 
> > > The driver internally will parse this array, convert it to nand pages
> > > and check internally on every read/write if this special configuration
> > > should used for that page or the normal one.
> > > 
> > > The reason for all of this is that qcom FOR SOME REASON, disable ECC for
> > > spare data only for these boot partition and we need to reflect this
> > > special configuration to mute these warning and to permit actually
> > > writing to these pages.
> > > 
> > > v4:
> > > - Fix wrong compatible set for boot-pages (ipq8074 instead of ipq806x)
> > > v3:
> > > - Fix typo in Docmunetation commit desription
> > > - Add items description for uint32-matrix
> > > v2:
> > > - Add fixes from Krzysztof in Documentation
> > > 
> > > Ansuel Smith (2):
> > >   mtd: nand: raw: qcom_nandc: add support for unprotected spare data
> > >     pages
> > >   dt-bindings: mtd: qcom_nandc: document qcom,boot-pages binding
> > > 
> > >  .../devicetree/bindings/mtd/qcom,nandc.yaml   |  26 +++
> > >  drivers/mtd/nand/raw/qcom_nandc.c             | 148 +++++++++++++++++-
> > >  2 files changed, 169 insertions(+), 5 deletions(-)
> > > 
> > > -- 
> > > 2.34.1
> > > 
> > 
> > -- 
> > மணிவண்ணன் சதாசிவம்
> 
> -- 
> 	Ansuel

-- 
மணிவண்ணன் சதாசிவம்