[PATCH 1/2] mtd: rawnand: brcmnand: Move Kconfig to driver folder

[Florian Fainelli]

In preparation for allowing each of the brcmnand stub to be built
separately, move the Kconfig entry to the driver folder.

Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
---
 drivers/mtd/nand/raw/Kconfig          | 22 +---------------------
 drivers/mtd/nand/raw/brcmnand/Kconfig | 21 +++++++++++++++++++++
 2 files changed, 22 insertions(+), 21 deletions(-)
 create mode 100644 drivers/mtd/nand/raw/brcmnand/Kconfig

diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index 8b6d7a515445..43a151b4c8fc 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -200,27 +200,7 @@ config MTD_NAND_TMIO
 	  Support for NAND flash connected to a Toshiba Mobile IO
 	  Controller in some PDAs, including the Sharp SL6000x.
 
-config MTD_NAND_BRCMNAND
-	tristate "Broadcom STB NAND controller"
-	depends on ARM || ARM64 || MIPS || COMPILE_TEST
-	depends on HAS_IOMEM
-	help
-	  Enables the Broadcom NAND controller driver. The controller was
-	  originally designed for Set-Top Box but is used on various BCM7xxx,
-	  BCM3xxx, BCM63xxx, iProc/Cygnus and more.
-
-if MTD_NAND_BRCMNAND
-
-config MTD_NAND_BRCMNAND_BCMA
-	tristate "Broadcom BCMA NAND controller"
-	depends on BCMA_NFLASH
-	depends on BCMA
-	help
-	  Enables the BRCMNAND controller over BCMA on BCM47186/BCM5358 SoCs.
-	  The glue driver will take care of performing the low-level I/O
-	  operations to interface the BRCMNAND controller over the BCMA bus.
-
-endif # MTD_NAND_BRCMNAND
+source "drivers/mtd/nand/raw/brcmnand/Kconfig"
 
 config MTD_NAND_BCM47XXNFLASH
 	tristate "BCM4706 BCMA NAND controller"
diff --git a/drivers/mtd/nand/raw/brcmnand/Kconfig b/drivers/mtd/nand/raw/brcmnand/Kconfig
new file mode 100644
index 000000000000..d5a0265525ca
--- /dev/null
+++ b/drivers/mtd/nand/raw/brcmnand/Kconfig
@@ -0,0 +1,21 @@
+config MTD_NAND_BRCMNAND
+	tristate "Broadcom STB NAND controller"
+	depends on ARM || ARM64 || MIPS || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  Enables the Broadcom NAND controller driver. The controller was
+	  originally designed for Set-Top Box but is used on various BCM7xxx,
+	  BCM3xxx, BCM63xxx, iProc/Cygnus and more.
+
+if MTD_NAND_BRCMNAND
+
+config MTD_NAND_BRCMNAND_BCMA
+	tristate "Broadcom BCMA NAND controller"
+	depends on BCMA_NFLASH
+	depends on BCMA
+	help
+	  Enables the BRCMNAND controller over BCMA on BCM47186/BCM5358 SoCs.
+	  The glue driver will take care of performing the low-level I/O
+	  operations to interface the BRCMNAND controller over the BCMA bus.
+
+endif # MTD_NAND_BRCMNAND
-- 
2.25.1