[PATCH 01/11] spi: spi-nxp-fspi: enable runtime pm for fspi
haibo.chen at nxp.com
haibo.chen at nxp.com
Tue Jul 5 02:11:33 PDT 2022
From: Haibo Chen <haibo.chen at nxp.com>
Enable the runtime PM in fspi driver.
Also for system PM, On some board like i.MX8ULP-EVK board,
after system suspend, IOMUX module will lost power, so all
the pinctrl setting will lost when system resume back, need
driver to save/restore the pinctrl setting.
Signed-off-by: Han Xu <han.xu at nxp.com>
Signed-off-by: Haibo Chen <haibo.chen at nxp.com>
---
drivers/spi/spi-nxp-fspi.c | 111 ++++++++++++++++++++++++++++++++-----
1 file changed, 97 insertions(+), 14 deletions(-)
diff --git a/drivers/spi/spi-nxp-fspi.c b/drivers/spi/spi-nxp-fspi.c
index 2b0301fc971c..b2cd8e06f374 100644
--- a/drivers/spi/spi-nxp-fspi.c
+++ b/drivers/spi/spi-nxp-fspi.c
@@ -49,6 +49,8 @@
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pm_runtime.h>
#include <linux/pm_qos.h>
#include <linux/regmap.h>
#include <linux/sizes.h>
@@ -58,6 +60,8 @@
#include <linux/spi/spi.h>
#include <linux/spi/spi-mem.h>
+/* runtime pm timeout */
+#define FSPI_RPM_TIMEOUT 50 /* 50ms */
/*
* The driver only uses one single LUT entry, that is updated on
* each call of exec_op(). Index 0 is preset at boot with a basic
@@ -375,6 +379,8 @@ struct nxp_fspi {
struct mutex lock;
struct pm_qos_request pm_qos_req;
int selected;
+#define FSPI_INITILIZED (1 << 0)
+ int flags;
};
static inline int needs_ip_only(struct nxp_fspi *f)
@@ -866,6 +872,12 @@ static int nxp_fspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
mutex_lock(&f->lock);
+ err = pm_runtime_get_sync(f->dev);
+ if (err < 0) {
+ dev_err(f->dev, "Failed to enable clock %d\n", __LINE__);
+ goto err_mutex;
+ }
+
/* Wait for controller being ready. */
err = fspi_readl_poll_tout(f, f->iobase + FSPI_STS0,
FSPI_STS0_ARB_IDLE, 1, POLL_TOUT, true);
@@ -894,8 +906,14 @@ static int nxp_fspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
/* Invalidate the data in the AHB buffer. */
nxp_fspi_invalid(f);
+ pm_runtime_mark_last_busy(f->dev);
+ pm_runtime_put_autosuspend(f->dev);
+
mutex_unlock(&f->lock);
+ return err;
+err_mutex:
+ mutex_unlock(&f->lock);
return err;
}
@@ -1141,12 +1159,17 @@ static int nxp_fspi_probe(struct platform_device *pdev)
ret = PTR_ERR(f->clk);
goto err_put_ctrl;
}
+ }
- ret = nxp_fspi_clk_prep_enable(f);
- if (ret) {
- dev_err(dev, "can not enable the clock\n");
- goto err_put_ctrl;
- }
+ pm_runtime_enable(dev);
+ pm_runtime_set_autosuspend_delay(dev, FSPI_RPM_TIMEOUT);
+ pm_runtime_use_autosuspend(dev);
+
+ /* enable clock */
+ ret = pm_runtime_get_sync(f->dev);
+ if (ret < 0) {
+ dev_err(f->dev, "Failed to enable clock %d\n", __LINE__);
+ goto err_put_ctrl;
}
/* Clear potential interrupts */
@@ -1180,13 +1203,19 @@ static int nxp_fspi_probe(struct platform_device *pdev)
if (ret)
goto err_destroy_mutex;
+ pm_runtime_mark_last_busy(f->dev);
+ pm_runtime_put_autosuspend(f->dev);
+
+ /* indicate the controller has been initialized */
+ f->flags |= FSPI_INITILIZED;
+
return 0;
err_destroy_mutex:
mutex_destroy(&f->lock);
err_disable_clk:
- nxp_fspi_clk_disable_unprep(f);
+ pm_runtime_disable(dev);
err_put_ctrl:
spi_controller_put(ctlr);
@@ -1212,20 +1241,79 @@ static int nxp_fspi_remove(struct platform_device *pdev)
return 0;
}
-static int nxp_fspi_suspend(struct device *dev)
+#ifdef CONFIG_PM
+static int nxp_fspi_initialized(struct nxp_fspi *f)
+{
+ return f->flags & FSPI_INITILIZED;
+}
+
+static int nxp_fspi_need_reinit(struct nxp_fspi *f)
+{
+ /*
+ * we always use the controller in combination mode, so we check
+ * this register bit to determine if the controller once lost power,
+ * such as suspend/resume, and need to be re-init.
+ */
+
+ return !(readl(f->iobase + FSPI_MCR0) & FSPI_MCR0_OCTCOMB_EN);
+}
+
+static int nxp_fspi_runtime_suspend(struct device *dev)
{
+ struct nxp_fspi *f = dev_get_drvdata(dev);
+
+ nxp_fspi_clk_disable_unprep(f);
+
return 0;
}
-static int nxp_fspi_resume(struct device *dev)
+static int nxp_fspi_runtime_resume(struct device *dev)
{
struct nxp_fspi *f = dev_get_drvdata(dev);
- nxp_fspi_default_setup(f);
+ nxp_fspi_clk_prep_enable(f);
+
+ if (nxp_fspi_initialized(f) && nxp_fspi_need_reinit(f))
+ nxp_fspi_default_setup(f);
return 0;
}
+static int nxp_fspi_suspend(struct device *dev)
+{
+ int ret;
+
+ ret = pinctrl_pm_select_sleep_state(dev);
+ if (ret) {
+ dev_err(dev, "select flexspi sleep pinctrl failed!\n");
+ return ret;
+ }
+
+ return pm_runtime_force_suspend(dev);
+}
+
+static int nxp_fspi_resume(struct device *dev)
+{
+ int ret;
+
+ ret = pm_runtime_force_resume(dev);
+ if (ret)
+ return ret;
+
+ ret = pinctrl_pm_select_default_state(dev);
+ if (ret)
+ dev_err(dev, "select flexspi default pinctrl failed!\n");
+
+ return ret;
+}
+
+
+static const struct dev_pm_ops nxp_fspi_pm_ops = {
+ SET_RUNTIME_PM_OPS(nxp_fspi_runtime_suspend, nxp_fspi_runtime_resume, NULL)
+ SET_SYSTEM_SLEEP_PM_OPS(nxp_fspi_suspend, nxp_fspi_resume)
+};
+#endif /* CONFIG_PM */
+
static const struct of_device_id nxp_fspi_dt_ids[] = {
{ .compatible = "nxp,lx2160a-fspi", .data = (void *)&lx2160a_data, },
{ .compatible = "nxp,imx8mm-fspi", .data = (void *)&imx8mm_data, },
@@ -1244,11 +1332,6 @@ static const struct acpi_device_id nxp_fspi_acpi_ids[] = {
MODULE_DEVICE_TABLE(acpi, nxp_fspi_acpi_ids);
#endif
-static const struct dev_pm_ops nxp_fspi_pm_ops = {
- .suspend = nxp_fspi_suspend,
- .resume = nxp_fspi_resume,
-};
-
static struct platform_driver nxp_fspi_driver = {
.driver = {
.name = "nxp-fspi",
--
2.25.1
More information about the linux-mtd
mailing list