[PATCH v3 19/25] mtd: spi-nor: core: Move spi_nor_set_addr_width() in spi_nor_setup()

[Tudor Ambarus]

spi_nor_setup() configures the SPI NOR memory. Setting the addr width
is too a configuration, hence we can move the spi_nor_set_addr_width()
in spi_nor_setup().

Signed-off-by: Tudor Ambarus <tudor.ambarus at microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav at ti.com>
---
 drivers/mtd/spi-nor/core.c | 102 +++++++++++++++++++------------------
 1 file changed, 52 insertions(+), 50 deletions(-)

diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index c509f257a6c3..ea26f27a3229 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -2484,13 +2484,61 @@ static int spi_nor_default_setup(struct spi_nor *nor,
 	return 0;
 }
 
+static int spi_nor_set_addr_width(struct spi_nor *nor)
+{
+	if (nor->addr_width) {
+		/* already configured from SFDP */
+	} else if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) {
+		/*
+		 * In 8D-8D-8D mode, one byte takes half a cycle to transfer. So
+		 * in this protocol an odd address width cannot be used because
+		 * then the address phase would only span a cycle and a half.
+		 * Half a cycle would be left over. We would then have to start
+		 * the dummy phase in the middle of a cycle and so too the data
+		 * phase, and we will end the transaction with half a cycle left
+		 * over.
+		 *
+		 * Force all 8D-8D-8D flashes to use an address width of 4 to
+		 * avoid this situation.
+		 */
+		nor->addr_width = 4;
+	} else if (nor->info->addr_width) {
+		nor->addr_width = nor->info->addr_width;
+	} else {
+		nor->addr_width = 3;
+	}
+
+	if (nor->addr_width == 3 && nor->mtd.size > 0x1000000) {
+		/* enable 4-byte addressing if the device exceeds 16MiB */
+		nor->addr_width = 4;
+	}
+
+	if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) {
+		dev_dbg(nor->dev, "address width is too large: %u\n",
+			nor->addr_width);
+		return -EINVAL;
+	}
+
+	/* Set 4byte opcodes when possible. */
+	if (nor->addr_width == 4 && nor->flags & SNOR_F_4B_OPCODES &&
+	    !(nor->flags & SNOR_F_HAS_4BAIT))
+		spi_nor_set_4byte_opcodes(nor);
+
+	return 0;
+}
+
 static int spi_nor_setup(struct spi_nor *nor,
 			 const struct spi_nor_hwcaps *hwcaps)
 {
-	if (!nor->params->setup)
-		return 0;
+	int ret;
 
-	return nor->params->setup(nor, hwcaps);
+	if (nor->params->setup) {
+		ret = nor->params->setup(nor, hwcaps);
+		if (ret)
+			return ret;
+	}
+
+	return spi_nor_set_addr_width(nor);
 }
 
 /**
@@ -3079,49 +3127,6 @@ static const struct flash_info *spi_nor_match_id(struct spi_nor *nor,
 	return NULL;
 }
 
-static int spi_nor_set_addr_width(struct spi_nor *nor)
-{
-	if (nor->addr_width) {
-		/* already configured from SFDP */
-	} else if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) {
-		/*
-		 * In 8D-8D-8D mode, one byte takes half a cycle to transfer. So
-		 * in this protocol an odd address width cannot be used because
-		 * then the address phase would only span a cycle and a half.
-		 * Half a cycle would be left over. We would then have to start
-		 * the dummy phase in the middle of a cycle and so too the data
-		 * phase, and we will end the transaction with half a cycle left
-		 * over.
-		 *
-		 * Force all 8D-8D-8D flashes to use an address width of 4 to
-		 * avoid this situation.
-		 */
-		nor->addr_width = 4;
-	} else if (nor->info->addr_width) {
-		nor->addr_width = nor->info->addr_width;
-	} else {
-		nor->addr_width = 3;
-	}
-
-	if (nor->addr_width == 3 && nor->mtd.size > 0x1000000) {
-		/* enable 4-byte addressing if the device exceeds 16MiB */
-		nor->addr_width = 4;
-	}
-
-	if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) {
-		dev_dbg(nor->dev, "address width is too large: %u\n",
-			nor->addr_width);
-		return -EINVAL;
-	}
-
-	/* Set 4byte opcodes when possible. */
-	if (nor->addr_width == 4 && nor->flags & SNOR_F_4B_OPCODES &&
-	    !(nor->flags & SNOR_F_HAS_4BAIT))
-		spi_nor_set_4byte_opcodes(nor);
-
-	return 0;
-}
-
 static void spi_nor_debugfs_init(struct spi_nor *nor,
 				 const struct flash_info *info)
 {
@@ -3253,15 +3258,12 @@ int spi_nor_scan(struct spi_nor *nor, const char *name,
 	 * - select op codes for (Fast) Read, Page Program and Sector Erase.
 	 * - set the number of dummy cycles (mode cycles + wait states).
 	 * - set the SPI protocols for register and memory accesses.
+	 * - set the address width.
 	 */
 	ret = spi_nor_setup(nor, hwcaps);
 	if (ret)
 		return ret;
 
-	ret = spi_nor_set_addr_width(nor);
-	if (ret)
-		return ret;
-
 	/* Send all the required SPI flash commands to initialize device */
 	ret = spi_nor_init(nor);
 	if (ret)
-- 
2.25.1