[PATCH v3 1/3] spi: spi-mem: add automatic poll status functions
Patrice CHOTARD
patrice.chotard at foss.st.com
Tue May 18 04:50:35 PDT 2021
Hi Boris
On 5/18/21 1:30 PM, Boris Brezillon wrote:
> On Tue, 18 May 2021 11:39:49 +0200
> <patrice.chotard at foss.st.com> wrote:
>
>> From: Patrice Chotard <patrice.chotard at foss.st.com>
>>
>> With STM32 QSPI, it is possible to poll the status register of the device.
>> This could be done to offload the CPU during an operation (erase or
>> program a SPI NAND for example).
>>
>> spi_mem_poll_status API has been added to handle this feature.
>> This new function take care of the offload/non-offload cases.
>>
>> For the non-offload case, use read_poll_timeout() to poll the status in
>> order to release CPU during this phase.
>> For example, previously, when erasing large area, in non-offload case,
>> CPU load can reach ~50%, now it decrease to ~35%.
>>
>> Signed-off-by: Patrice Chotard <patrice.chotard at foss.st.com>
>> Signed-off-by: Christophe Kerello <christophe.kerello at foss.st.com>
>> ---
>> Changes in v3:
>> - Add spi_mem_read_status() which allows to read 8 or 16 bits status.
>> - Add initial_delay_us and polling_delay_us parameters to spi_mem_poll_status()
>> and also to poll_status() callback.
>> - Move spi_mem_supports_op() in SW-based polling case.
>> - Add delay before invoking read_poll_timeout().
>> - Remove the reinit/wait_for_completion() added in v2.
>>
>> Changes in v2:
>> - Indicates the spi_mem_poll_status() timeout unit
>> - Use 2-byte wide status register
>> - Add spi_mem_supports_op() call in spi_mem_poll_status()
>> - Add completion management in spi_mem_poll_status()
>> - Add offload/non-offload case management in spi_mem_poll_status()
>> - Optimize the non-offload case by using read_poll_timeout()
>>
>> drivers/spi/spi-mem.c | 85 +++++++++++++++++++++++++++++++++++++
>> include/linux/spi/spi-mem.h | 14 ++++++
>> 2 files changed, 99 insertions(+)
>>
>> diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
>> index 1513553e4080..257dc501d5df 100644
>> --- a/drivers/spi/spi-mem.c
>> +++ b/drivers/spi/spi-mem.c
>> @@ -6,6 +6,7 @@
>> * Author: Boris Brezillon <boris.brezillon at bootlin.com>
>> */
>> #include <linux/dmaengine.h>
>> +#include <linux/iopoll.h>
>> #include <linux/pm_runtime.h>
>> #include <linux/spi/spi.h>
>> #include <linux/spi/spi-mem.h>
>> @@ -743,6 +744,89 @@ static inline struct spi_mem_driver *to_spi_mem_drv(struct device_driver *drv)
>> return container_of(drv, struct spi_mem_driver, spidrv.driver);
>> }
>>
>> +int spi_mem_read_status(struct spi_mem *mem,
>> + const struct spi_mem_op *op,
>> + u16 *status)
>> +{
>> + const u8 *bytes = (u8 *)op->data.buf.in;
>> + int ret;
>> +
>> + ret = spi_mem_exec_op(mem, op);
>> + if (ret)
>> + return ret;
>> +
>> + if (op->data.nbytes > 1)
>> + *status = ((u16)bytes[0] << 8) | bytes[1];
>> + else
>> + *status = bytes[0];
>> +
>> + return 0;
>> +}
>> +
>> +/**
>> + * spi_mem_poll_status() - Poll memory device status
>> + * @mem: SPI memory device
>> + * @op: the memory operation to execute
>> + * @mask: status bitmask to ckeck
>> + * @match: (status & mask) expected value
>> + * @initial_delay_us: delay in us before starting to poll
>> + * @polling_delay_us: time to sleep between reads in us
>> + * @timeout_ms: timeout in milliseconds
>> + *
>> + * This function send a polling status request to the controller driver
>> + *
>> + * Return: 0 in case of success, -ETIMEDOUT in case of error,
>> + * -EOPNOTSUPP if not supported.
>> + */
>> +int spi_mem_poll_status(struct spi_mem *mem,
>> + const struct spi_mem_op *op,
>> + u16 mask, u16 match,
>> + unsigned long initial_delay_us,
>> + unsigned long polling_delay_us,
>> + u16 timeout_ms)
>> +{
>> + struct spi_controller *ctlr = mem->spi->controller;
>> + int ret = -EOPNOTSUPP;
>> + int read_status_ret;
>> + u16 status;
>> +
>> + if (op->data.nbytes < 1 || op->data.nbytes > 2)
>> + return -EINVAL;
>> +
>> + if (ctlr->mem_ops && ctlr->mem_ops->poll_status) {
>> + ret = spi_mem_access_start(mem);
>> + if (ret)
>> + return ret;
>> +
>> + ret = ctlr->mem_ops->poll_status(mem, op, mask, match,
>> + initial_delay_us, polling_delay_us,
>> + timeout_ms);
>> +
>> + spi_mem_access_end(mem);
>> + }
>> +
>> + if (ret == -EOPNOTSUPP) {
>> + if (!spi_mem_supports_op(mem, op))
>> + return ret;
>> +
>> + if (initial_delay_us < 10)
>> + udelay(initial_delay_us);
>> + else
>> + usleep_range((initial_delay_us >> 2) + 1,
>> + initial_delay_us);
>> +
>> + ret = read_poll_timeout(spi_mem_read_status, read_status_ret,
>> + (read_status_ret || ((status) & mask) == match),
>> + polling_delay_us, timeout_ms * 1000, false, mem,
>> + op, &status);
>> + if (read_status_ret)
>> + return read_status_ret;
>> + }
>> +
>> + return ret;
>> +}
>> +EXPORT_SYMBOL_GPL(spi_mem_poll_status);
>> +
>> static int spi_mem_probe(struct spi_device *spi)
>> {
>> struct spi_mem_driver *memdrv = to_spi_mem_drv(spi->dev.driver);
>> @@ -763,6 +847,7 @@ static int spi_mem_probe(struct spi_device *spi)
>> if (IS_ERR_OR_NULL(mem->name))
>> return PTR_ERR_OR_ZERO(mem->name);
>>
>> + init_completion(&ctlr->xfer_completion);
>
> Is this still needed?
No, i forgot to remove it when reworking this v3
Thanks
Patrice
>
>> spi_set_drvdata(spi, mem);
>>
>> return memdrv->probe(mem);
>> diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
>> index 2b65c9edc34e..10375d9ad747 100644
>> --- a/include/linux/spi/spi-mem.h
>> +++ b/include/linux/spi/spi-mem.h
>> @@ -250,6 +250,7 @@ static inline void *spi_mem_get_drvdata(struct spi_mem *mem)
>> * the currently mapped area), and the caller of
>> * spi_mem_dirmap_write() is responsible for calling it again in
>> * this case.
>> + * @poll_status: poll memory device status
>> *
>> * This interface should be implemented by SPI controllers providing an
>> * high-level interface to execute SPI memory operation, which is usually the
>> @@ -274,6 +275,12 @@ struct spi_controller_mem_ops {
>> u64 offs, size_t len, void *buf);
>> ssize_t (*dirmap_write)(struct spi_mem_dirmap_desc *desc,
>> u64 offs, size_t len, const void *buf);
>> + int (*poll_status)(struct spi_mem *mem,
>> + const struct spi_mem_op *op,
>> + u16 mask, u16 match,
>> + unsigned long initial_delay_us,
>> + unsigned long polling_rate_us,
>> + unsigned long timeout_ms);
>> };
>>
>> /**
>> @@ -369,6 +376,13 @@ devm_spi_mem_dirmap_create(struct device *dev, struct spi_mem *mem,
>> void devm_spi_mem_dirmap_destroy(struct device *dev,
>> struct spi_mem_dirmap_desc *desc);
>>
>> +int spi_mem_poll_status(struct spi_mem *mem,
>> + const struct spi_mem_op *op,
>> + u16 mask, u16 match,
>> + unsigned long initial_delay_us,
>> + unsigned long polling_delay_us,
>> + u16 timeout);
>> +
>> int spi_mem_driver_register_with_owner(struct spi_mem_driver *drv,
>> struct module *owner);
>>
>
More information about the linux-mtd
mailing list