[PATCH] mtd: rawnand: qcom: avoid write to obsolete register

[mdalam at codeaurora.org]

On 2021-04-24 00:51, Md Sadre Alam wrote:
> QPIC_EBI2_ECC_BUF_CFG register got obsolete from QPIC V2.0 onwards.
> Avoid writing this register if QPIC version is V2.0 or newer.
> 
> Signed-off-by: Md Sadre Alam <mdalam at codeaurora.org>
> ---
>  drivers/mtd/nand/raw/qcom_nandc.c | 17 +++++++++++------
>  1 file changed, 11 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/mtd/nand/raw/qcom_nandc.c
> b/drivers/mtd/nand/raw/qcom_nandc.c
> index fd4c318..8c5205c 100644
> --- a/drivers/mtd/nand/raw/qcom_nandc.c
> +++ b/drivers/mtd/nand/raw/qcom_nandc.c
> @@ -714,7 +714,8 @@ static void update_rw_regs(struct qcom_nand_host
> *host, int num_cw, bool read)
>  	nandc_set_reg(nandc, NAND_DEV0_CFG0, cfg0);
>  	nandc_set_reg(nandc, NAND_DEV0_CFG1, cfg1);
>  	nandc_set_reg(nandc, NAND_DEV0_ECC_CFG, ecc_bch_cfg);
> -	nandc_set_reg(nandc, NAND_EBI2_ECC_BUF_CFG, host->ecc_buf_cfg);
> +	if (!nandc->props->qpic_v2)
> +		nandc_set_reg(nandc, NAND_EBI2_ECC_BUF_CFG, host->ecc_buf_cfg);
>  	nandc_set_reg(nandc, NAND_FLASH_STATUS, host->clrflashstatus);
>  	nandc_set_reg(nandc, NAND_READ_STATUS, host->clrreadstatus);
>  	nandc_set_reg(nandc, NAND_EXEC_CMD, 1);
> @@ -1083,7 +1084,8 @@ static void config_nand_page_read(struct
> qcom_nand_controller *nandc)
>  {
>  	write_reg_dma(nandc, NAND_ADDR0, 2, 0);
>  	write_reg_dma(nandc, NAND_DEV0_CFG0, 3, 0);
> -	write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1, 0);
> +	if (!nandc->props->qpic_v2)
> +		write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1, 0);
>  	write_reg_dma(nandc, NAND_ERASED_CW_DETECT_CFG, 1, 0);
>  	write_reg_dma(nandc, NAND_ERASED_CW_DETECT_CFG, 1,
>  		      NAND_ERASED_CW_SET | NAND_BAM_NEXT_SGL);
> @@ -1132,8 +1134,9 @@ static void config_nand_page_write(struct
> qcom_nand_controller *nandc)
>  {
>  	write_reg_dma(nandc, NAND_ADDR0, 2, 0);
>  	write_reg_dma(nandc, NAND_DEV0_CFG0, 3, 0);
> -	write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1,
> -		      NAND_BAM_NEXT_SGL);
> +	if (!nandc->props->qpic_v2)
> +		write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1,
> +			      NAND_BAM_NEXT_SGL);
>  }
> 
>  /*
> @@ -1187,7 +1190,8 @@ static int nandc_param(struct qcom_nand_host 
> *host)
>  					| 2 << WR_RD_BSY_GAP
>  					| 0 << WIDE_FLASH
>  					| 1 << DEV0_CFG1_ECC_DISABLE);
> -	nandc_set_reg(nandc, NAND_EBI2_ECC_BUF_CFG, 1 << 
> ECC_CFG_ECC_DISABLE);
> +	if (!nandc->props->qpic_v2)
> +		nandc_set_reg(nandc, NAND_EBI2_ECC_BUF_CFG, 1 << 
> ECC_CFG_ECC_DISABLE);
> 
>  	/* configure CMD1 and VLD for ONFI param probing in QPIC v1 */
>  	if (!nandc->props->qpic_v2) {
> @@ -2628,7 +2632,8 @@ static int qcom_nand_attach_chip(struct nand_chip 
> *chip)
>  				| ecc_mode << ECC_MODE
>  				| host->ecc_bytes_hw << ECC_PARITY_SIZE_BYTES_BCH;
> 
> -	host->ecc_buf_cfg = 0x203 << NUM_STEPS;
> +	if (!nandc->props->qpic_v2)
> +		host->ecc_buf_cfg = 0x203 << NUM_STEPS;
> 
>  	host->clrflashstatus = FS_READY_BSY_N;
>  	host->clrreadstatus = 0xc0;


ping! Hi Miquel could you review this change and let me know if more 
info needed.