[PATCH v7 9/9] arm64: dts: rockchip: Enable SFC for Odroid Go Advance

Jon Lin jon.lin at rock-chips.com
Thu Jun 10 20:54:09 PDT 2021


On 6/11/21 11:38 AM, Chris Morgan wrote:
> On Fri, Jun 11, 2021 at 10:26:35AM +0800, Jon Lin wrote:
>> Hi Chris
>>
>> May you attach the XT25F128B device code to me, and I'll try to work it out.
> Sure, here is the patch I am using:
>
> https://patchwork.ozlabs.org/project/linux-mtd/patch/SN6PR06MB5342C82F372F37FB8E21B327A57A9@SN6PR06MB5342.namprd06.prod.outlook.com/

this patch works well in my rk3308 tx-2 rx-2 XT25F128BSSIGU case.

# dd if=/tmp/rand.img of=/dev/mtdblock0 bs=4096 seek=1024
1024+0 records in
1024+0 records out
#
# dd if=/dev/mtd0 of=/tmp/rand1.img bs=4096 skip=1024 count=1024

1024+0 records in
1024+0 records out
#
#
# md5sum /tmp/*.img
83e45a56766168b47e6db1d41b1b403d  /tmp/rand.img
83e45a56766168b47e6db1d41b1b403d  /tmp/rand1.img
#
# dmesg | grep XT25F128BSSIGU
[    0.200738] spi-nor spi3.0: XT25F128BSSIGU (16384 Kbytes)
#

>
>> On 6/11/21 1:36 AM, Chris Morgan wrote:
>>> On Wed, Jun 09, 2021 at 10:13:48PM +0800, Jon Lin wrote:
>>>> From: Chris Morgan <macromorgan at hotmail.com>
>>>>
>>>> This enables the Rockchip Serial Flash Controller for the Odroid Go
>>>> Advance. Note that while the attached SPI NOR flash and the controller
>>>> both support quad read mode, only 2 of the required 4 pins are present.
>>>> The rx and tx bus width is set to 2 for this reason.
>>>>
>>>> Signed-off-by: Chris Morgan <macromorgan at hotmail.com>
>>>> Signed-off-by: Jon Lin <jon.lin at rock-chips.com>
>>>> ---
>>>>
>>>> Changes in v7: None
>>>> Changes in v6: None
>>>> Changes in v5: None
>>>> Changes in v4: None
>>>> Changes in v3: None
>>>> Changes in v2: None
>>>> Changes in v1: None
>>>>
>>>>    .../boot/dts/rockchip/rk3326-odroid-go2.dts      | 16 ++++++++++++++++
>>>>    1 file changed, 16 insertions(+)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
>>>> index 49c97f76df77..f78e11dd8447 100644
>>>> --- a/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
>>>> +++ b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
>>>> @@ -484,6 +484,22 @@
>>>>    	status = "okay";
>>>>    };
>>>> +&sfc {
>>>> +	pinctrl-0 = <&sfc_clk &sfc_cs0 &sfc_bus2>;
>>>> +	pinctrl-names = "default";
>>>> +	#address-cells = <1>;
>>>> +	#size-cells = <0>;
>>>> +	status = "okay";
>>>> +
>>>> +	flash at 0 {
>>>> +		compatible = "jedec,spi-nor";
>>>> +		reg = <0>;
>>>> +		spi-max-frequency = <108000000>;
>>>> +		spi-rx-bus-width = <2>;
>>>> +		spi-tx-bus-width = <2>;
>>> Note that I am still working with Jon Lin to research this, but it was
>>> found in testing that if I set the tx bus width to 1 the problems I
>>> encountered in earlier are resolved. At this time I do not know if it
>>> is an issue with the driver for the flash controller, or if the NOR, or
>>> board itself has some sort of errata which prevent dual tx from working
>>> correctly. Note that as of right now the flash chip I am using (an
>>> XTX XT25F128B) is not currently supported in mainline, so it's very
>>> possible this is some sort of errata with the chip. It's also possible
>>> that there is something with the board that is interferring with dual
>>> mode TX.  When Jon comes back that he has tested dual mode on the SFC
>>> with a different board/chip I will recommend that we change the tx
>>> bus width here to a 1, and then once the XT25F128B gets mainlined we
>>> can see if someone else has issues with dual tx mode so we can note
>>> that as a problem with the chip. Or maybe there is something weird
>>> with dual tx mode yet on the SFC driver/controller, I don't know yet.
>>> I'm all too happy to work with a Rockchip engineer so things like
>>> this can be determined before we hit mainline. :-)
>>>
>>> The XTX25F128B driver is currently awaiting a decision on how to handle
>>> continuation codes, as this chip ID should be using continuation codes,
>>> but doesn't appear to return them when you query for manufacturer ID.
>>> So I should also note in the commit here that the SFC will still be
>>> unusable on the Odroid Go Advance until the XTX25F128B is also
>>> mainlined.
>>>
>>> Thank you.
>>>
>>>> +	};
>>>> +};
>>>> +
>>>>    &tsadc {
>>>>    	status = "okay";
>>>>    };
>>>> -- 
>>>> 2.17.1
>>>>
>>>>
>>>>
>>>
>>
>
>





More information about the linux-mtd mailing list