[PATCH V3] mtd: rawnand: qcom: update last code word register
mdalam at codeaurora.org
mdalam at codeaurora.org
Thu Jan 28 16:48:46 EST 2021
On 2021-01-14 21:23, Miquel Raynal wrote:
> Hello,
>
> Md Sadre Alam <mdalam at codeaurora.org> wrote on Sun, 10 Jan 2021
> 09:31:45 +0530:
>
>> From QPIC version 2.0 onwards new register got added to
>
> a
>
>> read last codeword. This change will update the same.
>
> the? ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> Please reword this sentence.
Fixed this in V4 patch.
>
>> For first three code word READ_LOCATION_n register will be
>> use.For last code word READ_LOCATION_LAST_CW_n register will be
>> use.
>
> "For the first three codewords, READ_LOCATION_n registers will be used.
> The last codeword register will be accessed through
> READ_LOCATION_LAST_CW_n."
>
> Also, please specify what these registers store.
The location register is mainly use for reading controller
buffer via BAM mode. The bits of the register
"NAND_READ_LOCATION_LAST_CW_n, n=0..4"
as follow:
[9:0]-bits : (OFFSET) This bit defines the offset from the buffer base
address to be picked up for DMA.
[25:16]-bits: (SIZE) This bit of every register will define the size
of the chunk for DMA.
31-bit : (LAST) If this bit is set, the controller takes the
particular register to specify the last chunk
of data made available for DMA. This chunk is part
of the internal buffer of the controller.
>
>> Signed-off-by: Md Sadre Alam <mdalam at codeaurora.org>
>
> Could someone please test this patch?
I have tested this patch on IPQ5018 platform and its working fine.
>
>> ---
>> [V3]
>> * Added else condition for last code word in update_rw_regs().
>> drivers/mtd/nand/raw/qcom_nandc.c | 84
>> ++++++++++++++++++++++++++++++++-------
>> 1 file changed, 70 insertions(+), 14 deletions(-)
>>
>> diff --git a/drivers/mtd/nand/raw/qcom_nandc.c
>> b/drivers/mtd/nand/raw/qcom_nandc.c
>> index 667e4bf..50ff6e3 100644
>> --- a/drivers/mtd/nand/raw/qcom_nandc.c
>> +++ b/drivers/mtd/nand/raw/qcom_nandc.c
>> @@ -48,6 +48,10 @@
>> #define NAND_READ_LOCATION_1 0xf24
>> #define NAND_READ_LOCATION_2 0xf28
>> #define NAND_READ_LOCATION_3 0xf2c
>> +#define NAND_READ_LOCATION_LAST_CW_0 0xf40
>> +#define NAND_READ_LOCATION_LAST_CW_1 0xf44
>> +#define NAND_READ_LOCATION_LAST_CW_2 0xf48
>> +#define NAND_READ_LOCATION_LAST_CW_3 0xf4c
>>
>> /* dummy register offsets, used by write_reg_dma */
>> #define NAND_DEV_CMD1_RESTORE 0xdead
>> @@ -187,6 +191,12 @@ nandc_set_reg(nandc,
>> NAND_READ_LOCATION_##reg, \
>> ((size) << READ_LOCATION_SIZE) | \
>> ((is_last) << READ_LOCATION_LAST))
>>
>> +#define nandc_set_read_loc_last(nandc, reg, offset, size, is_last) \
>> +nandc_set_reg(nandc, NAND_READ_LOCATION_LAST_CW_##reg, \
>> + ((offset) << READ_LOCATION_OFFSET) | \
>> + ((size) << READ_LOCATION_SIZE) | \
>> + ((is_last) << READ_LOCATION_LAST))
>> +
>> /*
>> * Returns the actual register address for all NAND_DEV_ registers
>> * (i.e. NAND_DEV_CMD0, NAND_DEV_CMD1, NAND_DEV_CMD2 and
>> NAND_DEV_CMD_VLD)
>> @@ -316,6 +326,10 @@ struct nandc_regs {
>> __le32 read_location1;
>> __le32 read_location2;
>> __le32 read_location3;
>> + __le32 read_location_last0;
>> + __le32 read_location_last1;
>> + __le32 read_location_last2;
>> + __le32 read_location_last3;
>>
>> __le32 erased_cw_detect_cfg_clr;
>> __le32 erased_cw_detect_cfg_set;
>> @@ -644,6 +658,14 @@ static __le32 *offset_to_nandc_reg(struct
>> nandc_regs *regs, int offset)
>> return ®s->read_location2;
>> case NAND_READ_LOCATION_3:
>> return ®s->read_location3;
>> + case NAND_READ_LOCATION_LAST_CW_0:
>> + return ®s->read_location_last0;
>> + case NAND_READ_LOCATION_LAST_CW_1:
>> + return ®s->read_location_last1;
>> + case NAND_READ_LOCATION_LAST_CW_2:
>> + return ®s->read_location_last2;
>> + case NAND_READ_LOCATION_LAST_CW_3:
>> + return ®s->read_location_last3;
>> default:
>> return NULL;
>> }
>> @@ -719,9 +741,14 @@ static void update_rw_regs(struct qcom_nand_host
>> *host, int num_cw, bool read)
>> nandc_set_reg(nandc, NAND_READ_STATUS, host->clrreadstatus);
>> nandc_set_reg(nandc, NAND_EXEC_CMD, 1);
>>
>> - if (read)
>> - nandc_set_read_loc(nandc, 0, 0, host->use_ecc ?
>> - host->cw_data : host->cw_size, 1);
>> + if (read) {
>> + if (nandc->props->qpic_v2)
>> + nandc_set_read_loc_last(nandc, 0, 0, host->use_ecc ?
>> + host->cw_data : host->cw_size, 1);
>> + else
>> + nandc_set_read_loc(nandc, 0, 0, host->use_ecc ?
>> + host->cw_data : host->cw_size, 1);
>> + }
>> }
>>
>> /*
>> @@ -1096,9 +1123,13 @@ static void config_nand_page_read(struct
>> qcom_nand_controller *nandc)
>> static void
>> config_nand_cw_read(struct qcom_nand_controller *nandc, bool use_ecc)
>> {
>> - if (nandc->props->is_bam)
>> + if (nandc->props->is_bam) {
>> + if (nandc->props->qpic_v2)
>> + write_reg_dma(nandc, NAND_READ_LOCATION_LAST_CW_0,
>> + 1, NAND_BAM_NEXT_SGL);
>> write_reg_dma(nandc, NAND_READ_LOCATION_0, 4,
>> NAND_BAM_NEXT_SGL);
>> + }
>>
>> write_reg_dma(nandc, NAND_FLASH_CMD, 1, NAND_BAM_NEXT_SGL);
>> write_reg_dma(nandc, NAND_EXEC_CMD, 1, NAND_BAM_NEXT_SGL);
>> @@ -1633,16 +1664,28 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd,
>> struct nand_chip *chip,
>> }
>>
>> if (nandc->props->is_bam) {
>> - nandc_set_read_loc(nandc, 0, read_loc, data_size1, 0);
>> + if (nandc->props->qpic_v2 && cw == (ecc->steps - 1))
>> + nandc_set_read_loc_last(nandc, 0, read_loc, data_size1, 0);
>> + else
>> + nandc_set_read_loc(nandc, 0, read_loc, data_size1, 0);
>
> You repeat many times this logic, a helper to avoid this extra
> indentation level with the if/else block is needed.
Fixed this V4 patch.
>
>> read_loc += data_size1;
>>
>> - nandc_set_read_loc(nandc, 1, read_loc, oob_size1, 0);
>> + if (nandc->props->qpic_v2 && cw == (ecc->steps - 1))
>> + nandc_set_read_loc_last(nandc, 1, read_loc, oob_size1, 0);
>> + else
>> + nandc_set_read_loc(nandc, 1, read_loc, oob_size1, 0);
>> read_loc += oob_size1;
>>
>> - nandc_set_read_loc(nandc, 2, read_loc, data_size2, 0);
>> + if (nandc->props->qpic_v2 && cw == (ecc->steps - 1))
>> + nandc_set_read_loc_last(nandc, 2, read_loc, data_size2, 0);
>> + else
>> + nandc_set_read_loc(nandc, 2, read_loc, data_size2, 0);
>> read_loc += data_size2;
>>
>> - nandc_set_read_loc(nandc, 3, read_loc, oob_size2, 1);
>> + if (nandc->props->qpic_v2 && cw == (ecc->steps - 1))
>> + nandc_set_read_loc_last(nandc, 3, read_loc, oob_size2, 0);
>> + else
>> + nandc_set_read_loc(nandc, 3, read_loc, oob_size2, 1);
>> }
>
> Thanks,
> Miquèl
More information about the linux-mtd
mailing list