[PATCH] mtd: rawnand: qcom: update last code word register
Miquel Raynal
miquel.raynal at bootlin.com
Tue Feb 16 03:16:13 EST 2021
Hello,
Md Sadre Alam <mdalam at codeaurora.org> wrote on Tue, 16 Feb 2021
00:46:42 +0530:
> From QPIC version 2.0 onwards new register got added to
> read last codeword. This change will add the READ_LOCATION_LAST_CW_n
> register.
>
> For first three code word READ_LOCATION_n register will be
> use.For last code word READ_LOCATION_LAST_CW_n register will be
> use.
>
> Signed-off-by: Md Sadre Alam <mdalam at codeaurora.org>
> ---
> [V6]
It is also very important that you mark the version in the subject:
[PATCH v6] mtd: rawnand: etc
Otherwise it is difficult to keep track on the changes.
> * Updated write_reg_dma() function in "v6"
> * Removed extra indentation level in read_page_ecc() to read last code word in "v6"
> * Removed boolean check in config_nand_cw_read() in "v6"
> drivers/mtd/nand/raw/qcom_nandc.c | 118 ++++++++++++++++++++++++++++----------
> 1 file changed, 87 insertions(+), 31 deletions(-)
>
> diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
> index 667e4bf..bae352f 100644
> --- a/drivers/mtd/nand/raw/qcom_nandc.c
> +++ b/drivers/mtd/nand/raw/qcom_nandc.c
> @@ -48,6 +48,10 @@
> #define NAND_READ_LOCATION_1 0xf24
> #define NAND_READ_LOCATION_2 0xf28
> #define NAND_READ_LOCATION_3 0xf2c
> +#define NAND_READ_LOCATION_LAST_CW_0 0xf40
> +#define NAND_READ_LOCATION_LAST_CW_1 0xf44
> +#define NAND_READ_LOCATION_LAST_CW_2 0xf48
> +#define NAND_READ_LOCATION_LAST_CW_3 0xf4c
>
> /* dummy register offsets, used by write_reg_dma */
> #define NAND_DEV_CMD1_RESTORE 0xdead
> @@ -181,8 +185,14 @@
> #define ECC_BCH_4BIT BIT(2)
> #define ECC_BCH_8BIT BIT(3)
>
> -#define nandc_set_read_loc(nandc, reg, offset, size, is_last) \
> -nandc_set_reg(nandc, NAND_READ_LOCATION_##reg, \
> +#define nandc_set_read_loc_first(nandc, reg, offset, size, is_last) \
> +nandc_set_reg(nandc, reg, \
> + ((offset) << READ_LOCATION_OFFSET) | \
> + ((size) << READ_LOCATION_SIZE) | \
> + ((is_last) << READ_LOCATION_LAST))
> +
> +#define nandc_set_read_loc_last(nandc, reg, offset, size, is_last) \
> +nandc_set_reg(nandc, reg, \
> ((offset) << READ_LOCATION_OFFSET) | \
> ((size) << READ_LOCATION_SIZE) | \
> ((is_last) << READ_LOCATION_LAST))
> @@ -316,6 +326,10 @@ struct nandc_regs {
> __le32 read_location1;
> __le32 read_location2;
> __le32 read_location3;
> + __le32 read_location_last0;
> + __le32 read_location_last1;
> + __le32 read_location_last2;
> + __le32 read_location_last3;
>
> __le32 erased_cw_detect_cfg_clr;
> __le32 erased_cw_detect_cfg_set;
> @@ -644,6 +658,14 @@ static __le32 *offset_to_nandc_reg(struct nandc_regs *regs, int offset)
> return ®s->read_location2;
> case NAND_READ_LOCATION_3:
> return ®s->read_location3;
> + case NAND_READ_LOCATION_LAST_CW_0:
> + return ®s->read_location_last0;
> + case NAND_READ_LOCATION_LAST_CW_1:
> + return ®s->read_location_last1;
> + case NAND_READ_LOCATION_LAST_CW_2:
> + return ®s->read_location_last2;
> + case NAND_READ_LOCATION_LAST_CW_3:
> + return ®s->read_location_last3;
> default:
> return NULL;
> }
> @@ -661,6 +683,26 @@ static void nandc_set_reg(struct qcom_nand_controller *nandc, int offset,
> *reg = cpu_to_le32(val);
> }
>
> +/* helper to configure location register values */
> +static void nandc_set_read_loc(struct nand_chip *chip, int cw, int reg,
> + int offset, int size, int is_last)
You know cw, you have access to chip->ecc.steps, so you can derive by
yourself if is_last is set or not. No need to forward it through
function calls.
> +{
> + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
> + struct nand_ecc_ctrl *ecc = &chip->ecc;
> +
> + int loc = NAND_READ_LOCATION_0;
> +
> + if (nandc->props->qpic_v2 && cw == (ecc->steps - 1))
> + loc = NAND_READ_LOCATION_LAST_CW_0;
> +
> + loc += reg * 4;
> +
> + if (nandc->props->qpic_v2 && cw == (ecc->steps - 1))
Just compute is_last a single time at the top of the helper and use it.
> + return nandc_set_read_loc_last(nandc, loc, offset, size, is_last);
> + else
> + return nandc_set_read_loc_first(nandc, loc, offset, size, is_last);
> +}
> +
> /* helper to configure address register values */
> static void set_address(struct qcom_nand_host *host, u16 column, int page)
> {
> @@ -685,6 +727,7 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read)
> {
> struct nand_chip *chip = &host->chip;
> struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
> + struct nand_ecc_ctrl *ecc = &chip->ecc;
> u32 cmd, cfg0, cfg1, ecc_bch_cfg;
>
> if (read) {
> @@ -719,9 +762,14 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read)
> nandc_set_reg(nandc, NAND_READ_STATUS, host->clrreadstatus);
> nandc_set_reg(nandc, NAND_EXEC_CMD, 1);
>
> - if (read)
> - nandc_set_read_loc(nandc, 0, 0, host->use_ecc ?
> - host->cw_data : host->cw_size, 1);
> + if (read) {
> + if (nandc->props->qpic_v2)
> + nandc_set_read_loc(chip, ecc->steps - 1, 0, 0, host->use_ecc ?
> + host->cw_data : host->cw_size, 1);
> + else
> + nandc_set_read_loc(chip, 0, 0, 0, host->use_ecc ?
> + host->cw_data : host->cw_size, 1);
Here you should not have this extra indentation level as well,
nandc_set_read_log() should IMHO be able to hide the complexity of the
versions.
> + }
> }
>
> /*
> @@ -1079,8 +1127,10 @@ static int write_data_dma(struct qcom_nand_controller *nandc, int reg_off,
> * Helper to prepare DMA descriptors for configuring registers
> * before reading a NAND page.
> */
> -static void config_nand_page_read(struct qcom_nand_controller *nandc)
> +static void config_nand_page_read(struct nand_chip *chip)
> {
> + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
> +
I don't get why you change the parameter from nandc to chip. Honnestly
I don't think it is a bad thing, I'm just curious to understand why. If
you want to do that, please start with a first patch just doing the
conversion, and then a second patch adding LAST_CW support. Otherwise
it is blurry.
> write_reg_dma(nandc, NAND_ADDR0, 2, 0);
> write_reg_dma(nandc, NAND_DEV0_CFG0, 3, 0);
> write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1, 0);
> @@ -1094,11 +1144,19 @@ static void config_nand_page_read(struct qcom_nand_controller *nandc)
> * before reading each codeword in NAND page.
> */
> static void
> -config_nand_cw_read(struct qcom_nand_controller *nandc, bool use_ecc)
> +config_nand_cw_read(struct nand_chip *chip, bool use_ecc, int cw)
> {
> - if (nandc->props->is_bam)
> - write_reg_dma(nandc, NAND_READ_LOCATION_0, 4,
> - NAND_BAM_NEXT_SGL);
> + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
> + struct nand_ecc_ctrl *ecc = &chip->ecc;
> +
> + if (nandc->props->is_bam) {
> + if (nandc->props->qpic_v2 && cw == (ecc->steps - 1))
> + write_reg_dma(nandc, NAND_READ_LOCATION_LAST_CW_0, 4,
> + NAND_BAM_NEXT_SGL);
> + else
> + write_reg_dma(nandc, NAND_READ_LOCATION_0, 4,
> + NAND_BAM_NEXT_SGL);
> + }
Same here, I am pretty sure we can abstract the complexity.
>
> write_reg_dma(nandc, NAND_FLASH_CMD, 1, NAND_BAM_NEXT_SGL);
> write_reg_dma(nandc, NAND_EXEC_CMD, 1, NAND_BAM_NEXT_SGL);
> @@ -1117,11 +1175,11 @@ config_nand_cw_read(struct qcom_nand_controller *nandc, bool use_ecc)
> * single codeword in page
> */
> static void
> -config_nand_single_cw_page_read(struct qcom_nand_controller *nandc,
> - bool use_ecc)
> +config_nand_single_cw_page_read(struct nand_chip *chip,
> + bool use_ecc, int cw)
> {
> - config_nand_page_read(nandc);
> - config_nand_cw_read(nandc, use_ecc);
> + config_nand_page_read(chip);
> + config_nand_cw_read(chip, use_ecc, cw);
> }
>
> /*
> @@ -1205,7 +1263,7 @@ static int nandc_param(struct qcom_nand_host *host)
> nandc_set_reg(nandc, NAND_DEV_CMD_VLD_RESTORE, nandc->vld);
> }
>
> - nandc_set_read_loc(nandc, 0, 0, 512, 1);
> + nandc_set_read_loc(chip, 0, 0, 0, 512, 1);
>
> if (!nandc->props->qpic_v2) {
> write_reg_dma(nandc, NAND_DEV_CMD_VLD, 1, 0);
> @@ -1215,7 +1273,7 @@ static int nandc_param(struct qcom_nand_host *host)
> nandc->buf_count = 512;
> memset(nandc->data_buffer, 0xff, nandc->buf_count);
>
> - config_nand_single_cw_page_read(nandc, false);
> + config_nand_single_cw_page_read(chip, false, 0);
>
> read_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer,
> nandc->buf_count, 0);
> @@ -1617,7 +1675,7 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip,
> clear_bam_transaction(nandc);
> set_address(host, host->cw_size * cw, page);
> update_rw_regs(host, 1, true);
> - config_nand_page_read(nandc);
> + config_nand_page_read(chip);
>
> data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1);
> oob_size1 = host->bbm_size;
> @@ -1633,19 +1691,19 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip,
> }
>
> if (nandc->props->is_bam) {
> - nandc_set_read_loc(nandc, 0, read_loc, data_size1, 0);
> + nandc_set_read_loc(chip, cw, 0, read_loc, data_size1, 0);
> read_loc += data_size1;
>
> - nandc_set_read_loc(nandc, 1, read_loc, oob_size1, 0);
> + nandc_set_read_loc(chip, cw, 1, read_loc, oob_size1, 0);
> read_loc += oob_size1;
>
> - nandc_set_read_loc(nandc, 2, read_loc, data_size2, 0);
> + nandc_set_read_loc(chip, cw, 2, read_loc, data_size2, 0);
> read_loc += data_size2;
>
> - nandc_set_read_loc(nandc, 3, read_loc, oob_size2, 1);
> + nandc_set_read_loc(chip, cw, 3, read_loc, oob_size2, 1);
> }
>
> - config_nand_cw_read(nandc, false);
> + config_nand_cw_read(chip, false, cw);
>
> read_data_dma(nandc, reg_off, data_buf, data_size1, 0);
> reg_off += data_size1;
> @@ -1856,7 +1914,7 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf,
> u8 *data_buf_start = data_buf, *oob_buf_start = oob_buf;
> int i, ret;
>
> - config_nand_page_read(nandc);
> + config_nand_page_read(chip);
>
> /* queue cmd descs for each codeword */
> for (i = 0; i < ecc->steps; i++) {
> @@ -1873,18 +1931,16 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf,
>
> if (nandc->props->is_bam) {
> if (data_buf && oob_buf) {
> - nandc_set_read_loc(nandc, 0, 0, data_size, 0);
> - nandc_set_read_loc(nandc, 1, data_size,
> - oob_size, 1);
> + nandc_set_read_loc(chip, i, 0, 0, data_size, 0);
> + nandc_set_read_loc(chip, i, 1, data_size, oob_size, 1);
> } else if (data_buf) {
> - nandc_set_read_loc(nandc, 0, 0, data_size, 1);
> + nandc_set_read_loc(chip, i, 0, 0, data_size, 1);
> } else {
> - nandc_set_read_loc(nandc, 0, data_size,
> - oob_size, 1);
> + nandc_set_read_loc(chip, i, 0, data_size, oob_size, 1);
> }
> }
>
> - config_nand_cw_read(nandc, true);
> + config_nand_cw_read(chip, true, i);
>
> if (data_buf)
> read_data_dma(nandc, FLASH_BUF_ACC, data_buf,
> @@ -1946,7 +2002,7 @@ static int copy_last_cw(struct qcom_nand_host *host, int page)
> set_address(host, host->cw_size * (ecc->steps - 1), page);
> update_rw_regs(host, 1, true);
>
> - config_nand_single_cw_page_read(nandc, host->use_ecc);
> + config_nand_single_cw_page_read(chip, host->use_ecc, ecc->steps - 1);
>
> read_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer, size, 0);
>
Thanks,
Miquèl
More information about the linux-mtd
mailing list