[PATCH 2/2] mtd: spi-nor: Disable the flash quad mode in spi_nor_restore()
Yicong Yang
yangyicong at hisilicon.com
Wed Sep 2 06:12:42 EDT 2020
Hi Vignesh,
On 2020/9/2 15:50, Vignesh Raghavendra wrote:
> Hi Yicong,
>
> On 9/1/20 7:50 PM, Yicong Yang wrote:
>> Hi Mathhias and Pratyush,
>>
>> I've tested the following patch with s25fs128s1.
>> I left the flash quad enabled before managed by spi-nor driver,
>> and it'll stay QE after removed. So I think it'll also address the issue
>> mentioned. Please have a test.
>>
>> Regards,
>> Yicong
>>
>>
>> From 43aa1afa12a10036f722b272a9a39b8c83218f33 Mon Sep 17 00:00:00 2001
>> From: Yicong Yang <yangyicong at hisilicon.com>
>> Date: Tue, 1 Sep 2020 22:09:46 +0800
>> Subject: [PATCH] mtd: spi-nor: don't disable quad mode of flash whose is
>> originally enabled
>>
>> Currently we'll disable the flash's Quad mode when remove/shutdown in
>> spi_nor_restore(), no matter whether it's Quad enabled or not.
>> For flashes originally in Quad mode, it'll clear the flash's QE bit
>> and restore an incorrect state.
>>
>> Record the flash's original QE state, and don't disable the Quad mode
>> of these originally Quad enabled flash.
>>
> This will break backward compatibility... Imagine a new board being
> flashed from Kernel. Before this series, QE bit would be set at the end of flashing
> and ROM/bootloader (such as the one reported by Matthias) would work fine.
> After this series, QE bit would no longer be set and would most likely
> break boot..
>
> I still am unable to understand what is the underlying problem that is
> being addressed here?
>
> You mention addressing issue loading the driver in Quad mode first and reload it in
> Standard SPI/Dual mode. But per s25fs128s data sheet:
> "
> Quad Data Width (QUAD) CR1V[1]: When set to 1, this bit switches the data width of the device to 4-bit Quad Mode. That is, WP#
> becomes IO2 and IO3 / RESET# becomes an active I/O signal when CS# is low or the RESET# input when CS# is high. The WP#
> input is not monitored for its normal function and is internally set to high (inactive). The commands for Serial, and Dual I/O Read still
> function normally but, there is no need to drive the WP# input for those commands when switching between commands using
> different data path widths. Similarly, there is no requirement to drive the IO3 / RESET# during those commands (while CS# is low)."
>
> So setting QE bit should have no impact for serial/dual IO modes?
yes. and I reword the commit like below, as suggested by Tudor and send a v2 patch. This thread is the v1 one.
"If the flash's quad mode is enabled, it'll remain in the quad mode when
it's removed. If we drive the flash next time in Standard/Dual SPI mode,
the QE bit is not cleared and the function of flash's WP# and RESET#/HOLD#
have been switched to IO2 and IO3 and are not restored."
I believe we should restore the state of the flash when it's unloaded from the kernel. In previous code, if we load the flash
in Quad mode (originally in Standard SPI mode) and shutdown, its WP# and RESET# won't be restored correctly. Seems
the patch doesn't consider the condition that the flash has already in Quad mode before loaded and restore the flash
in a wrong state.
Regards
Yicong
>
> Regards
> Vignesh
>
>> Reported-by: Matthias Weisser <m.weisser.m at gmail.com>
>> Signed-off-by: Yicong Yang <yangyicong at hisilicon.com>
>> ---
>> drivers/mtd/spi-nor/core.c | 30 +++++++++++++++++++++++-------
>> include/linux/mtd/spi-nor.h | 3 +++
>> 2 files changed, 26 insertions(+), 7 deletions(-)
>>
>> diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
>> index 65eff4c..b13b3b3 100644
>> --- a/drivers/mtd/spi-nor/core.c
>> +++ b/drivers/mtd/spi-nor/core.c
>> @@ -1924,8 +1924,11 @@ int spi_nor_sr1_bit6_quad_enable(struct spi_nor *nor, bool enable)
>> if (ret)
>> return ret;
>>
>> - if ((enable && (nor->bouncebuf[0] & SR1_QUAD_EN_BIT6)) ||
>> - (!enable && !(nor->bouncebuf[0] & SR1_QUAD_EN_BIT6)))
>> + if (enable && (nor->bouncebuf[0] & SR1_QUAD_EN_BIT6)) {
>> + nor->orig_qe_state = true;
>> + return 0;
>> + }
>> + if (!enable && !(nor->bouncebuf[0] & SR1_QUAD_EN_BIT6))
>> return 0;
>>
>> if (enable)
>> @@ -1958,8 +1961,12 @@ int spi_nor_sr2_bit1_quad_enable(struct spi_nor *nor, bool enable)
>> if (ret)
>> return ret;
>>
>> - if ((enable && (nor->bouncebuf[0] & SR2_QUAD_EN_BIT1)) ||
>> - (!enable && !(nor->bouncebuf[0] & SR2_QUAD_EN_BIT1)))
>> + if (enable && (nor->bouncebuf[0] & SR2_QUAD_EN_BIT1)) {
>> + nor->orig_qe_state = true;
>> + return 0;
>> + }
>> +
>> + if (!enable && !(nor->bouncebuf[0] & SR2_QUAD_EN_BIT1))
>> return 0;
>>
>> if (enable)
>> @@ -1993,8 +2000,12 @@ int spi_nor_sr2_bit7_quad_enable(struct spi_nor *nor, bool enable)
>> ret = spi_nor_read_sr2(nor, sr2);
>> if (ret)
>> return ret;
>> - if ((enable && (*sr2 & SR2_QUAD_EN_BIT7)) ||
>> - (!enable && !(*sr2 & SR2_QUAD_EN_BIT7)))
>> + if (enable && (*sr2 & SR2_QUAD_EN_BIT7)) {
>> + nor->orig_qe_state = true;
>> + return 0;
>> + }
>> +
>> + if (!enable && !(*sr2 & SR2_QUAD_EN_BIT7))
>> return 0;
>>
>> /* Update the Quad Enable bit. */
>> @@ -3001,7 +3012,12 @@ void spi_nor_restore(struct spi_nor *nor)
>> nor->flags & SNOR_F_BROKEN_RESET)
>> nor->params->set_4byte_addr_mode(nor, false);
>>
>> - spi_nor_quad_enable(nor, false);
>> + /*
>> + * restore the flash's quad mode. if the flash's quad mode is
>> + * enabled originally, we'll not disable it.
>> + */
>> + if (!nor->orig_qe_state)
>> + spi_nor_quad_enable(nor, false);
>> }
>> EXPORT_SYMBOL_GPL(spi_nor_restore);
>>
>> diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
>> index 60bac2c..f343416 100644
>> --- a/include/linux/mtd/spi-nor.h
>> +++ b/include/linux/mtd/spi-nor.h
>> @@ -344,6 +344,8 @@ struct spi_nor_flash_parameter;
>> * @read_dummy: the dummy needed by the read operation
>> * @program_opcode: the program opcode
>> * @sst_write_second: used by the SST write operation
>> + * @orig_qe_state: used to indicate the flash's original Quad mode enable
>> + * state. True for enabled and false for disabled.
>> * @flags: flag options for the current SPI NOR (SNOR_F_*)
>> * @read_proto: the SPI protocol for read operations
>> * @write_proto: the SPI protocol for write operations
>> @@ -375,6 +377,7 @@ struct spi_nor {
>> enum spi_nor_protocol write_proto;
>> enum spi_nor_protocol reg_proto;
>> bool sst_write_second;
>> + bool orig_qe_state;
>> u32 flags;
>>
>> const struct spi_nor_controller_ops *controller_ops;
>>
> .
>
More information about the linux-mtd
mailing list