[PATCH v15 14/15] mtd: spi-nor: spansion: add support for Cypress Semper flash

[Vignesh Raghavendra]

Hi Pratyush,

On 10/2/20 1:50 AM, Pratyush Yadav wrote:
> +
> +/**
> + * spi_nor_cypress_octal_dtr_enable() - Enable octal DTR on Cypress flashes.
> + * @nor:		pointer to a 'struct spi_nor'
> + * @enable:              whether to enable or disable Octal DTR
> + *
> + * This also sets the memory access latency cycles to 24 to allow the flash to
> + * run at up to 200MHz.
> + *
> + * Return: 0 on success, -errno otherwise.
> + */
> +static int spi_nor_cypress_octal_dtr_enable(struct spi_nor *nor, bool enable)
> +{
> +	struct spi_mem_op op;
> +	u8 *buf = nor->bouncebuf;
> +	int ret;
> +
> +	if (enable) {
> +		/* Use 24 dummy cycles for memory array reads. */
> +		ret = spi_nor_write_enable(nor);
> +		if (ret)
> +			return ret;
> +
> +		*buf = SPINOR_REG_CYPRESS_CFR2V_MEMLAT_11_24;
> +		op = (struct spi_mem_op)
> +			SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
> +				   SPI_MEM_OP_ADDR(3, SPINOR_REG_CYPRESS_CFR2V,
> +						   1),
> +				   SPI_MEM_OP_NO_DUMMY,
> +				   SPI_MEM_OP_DATA_OUT(1, buf, 1));
> +
> +		ret = spi_mem_exec_op(nor->spimem, &op);
> +		if (ret)
> +			return ret;
> +
> +		ret = spi_nor_wait_till_ready(nor);
> +		if (ret)
> +			return ret;
> +
> +		nor->read_dummy = 24;
> +	}
> +
> +	/* Set/unset the octal and DTR enable bits. */
> +	ret = spi_nor_write_enable(nor);
> +	if (ret)
> +		return ret;
> +
> +	if (enable)
> +		*buf = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN;
> +	else
> +		*buf = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS;
> +
> +	op = (struct spi_mem_op)
> +		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
> +			   SPI_MEM_OP_ADDR(enable ? 3 : 4,
> +					   SPINOR_REG_CYPRESS_CFR5V,
> +					   1),
> +			   SPI_MEM_OP_NO_DUMMY,
> +			   SPI_MEM_OP_DATA_OUT(1, buf, 1));
> +
> +	if (!enable)
> +		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
> +
> +	ret = spi_mem_exec_op(nor->spimem, &op);
> +	if (ret)
> +		return ret;
> +
> +	/* Give some time for the mode change to take place. */
> +	usleep_range(1000, 1500);
> +

According to datasheet, it seems switch to Octal DTR mode is immediate.
So, I don't think this delay is necessary. Instead as a confirmation
that mode switch is successful can we just read back
SPINOR_REG_CYPRESS_CFR5V in Octal DTR mode and see if value reflects
what was written?

Same applies for 15/15 as well.

> +	return 0;
> +}
> +