[PATCH v15 03/15] mtd: spi-nor: add support for DTR protocol
Pratyush Yadav
p.yadav at ti.com
Thu Oct 1 16:20:33 EDT 2020
Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.
Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.
The xSPI spec says that "The program commands provide SPI backward
compatible commands for programming data...". So 8D-8D-8D page program
opcodes are populated with using 1S-1S-1S opcodes.
Signed-off-by: Pratyush Yadav <p.yadav at ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus at microchip.com>
---
drivers/mtd/spi-nor/core.c | 319 +++++++++++++++++++++++++++---------
drivers/mtd/spi-nor/core.h | 7 +
drivers/mtd/spi-nor/sfdp.c | 9 +-
include/linux/mtd/spi-nor.h | 51 ++++--
4 files changed, 290 insertions(+), 96 deletions(-)
diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index 7a3bf460a2fa..779e64974fea 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -40,6 +40,78 @@
#define SPI_NOR_MAX_ADDR_WIDTH 4
+/**
+ * spi_nor_get_cmd_ext() - Get the command opcode extension based on the
+ * extension type.
+ * @nor: pointer to a 'struct spi_nor'
+ * @op: pointer to the 'struct spi_mem_op' whose properties
+ * need to be initialized.
+ *
+ * Right now, only "repeat" and "invert" are supported.
+ *
+ * Return: The opcode extension.
+ */
+static u8 spi_nor_get_cmd_ext(const struct spi_nor *nor,
+ const struct spi_mem_op *op)
+{
+ switch (nor->cmd_ext_type) {
+ case SPI_NOR_EXT_INVERT:
+ return ~op->cmd.opcode;
+
+ case SPI_NOR_EXT_REPEAT:
+ return op->cmd.opcode;
+
+ default:
+ dev_err(nor->dev, "Unknown command extension type\n");
+ return 0;
+ }
+}
+
+/**
+ * spi_nor_spimem_setup_op() - Set up common properties of a spi-mem op.
+ * @nor: pointer to a 'struct spi_nor'
+ * @op: pointer to the 'struct spi_mem_op' whose properties
+ * need to be initialized.
+ * @proto: the protocol from which the properties need to be set.
+ */
+void spi_nor_spimem_setup_op(const struct spi_nor *nor,
+ struct spi_mem_op *op,
+ const enum spi_nor_protocol proto)
+{
+ u8 ext;
+
+ op->cmd.buswidth = spi_nor_get_protocol_inst_nbits(proto);
+
+ if (op->addr.nbytes)
+ op->addr.buswidth = spi_nor_get_protocol_addr_nbits(proto);
+
+ if (op->dummy.nbytes)
+ op->dummy.buswidth = spi_nor_get_protocol_addr_nbits(proto);
+
+ if (op->data.nbytes)
+ op->data.buswidth = spi_nor_get_protocol_data_nbits(proto);
+
+ if (spi_nor_protocol_is_dtr(proto)) {
+ /*
+ * SPIMEM supports mixed DTR modes, but right now we can only
+ * have all phases either DTR or STR. IOW, SPIMEM can have
+ * something like 4S-4D-4D, but SPI NOR can't. So, set all 4
+ * phases to either DTR or STR.
+ */
+ op->cmd.dtr = true;
+ op->addr.dtr = true;
+ op->dummy.dtr = true;
+ op->data.dtr = true;
+
+ /* 2 bytes per clock cycle in DTR mode. */
+ op->dummy.nbytes *= 2;
+
+ ext = spi_nor_get_cmd_ext(nor, op);
+ op->cmd.opcode = (op->cmd.opcode << 8) | ext;
+ op->cmd.nbytes = 2;
+ }
+}
+
/**
* spi_nor_spimem_bounce() - check if a bounce buffer is needed for the data
* transfer
@@ -85,17 +157,26 @@ static int spi_nor_spimem_exec_op(struct spi_nor *nor, struct spi_mem_op *op)
static int spi_nor_controller_ops_read_reg(struct spi_nor *nor, u8 opcode,
u8 *buf, size_t len)
{
+ if (spi_nor_protocol_is_dtr(nor->reg_proto))
+ return -EOPNOTSUPP;
+
return nor->controller_ops->read_reg(nor, opcode, buf, len);
}
static int spi_nor_controller_ops_write_reg(struct spi_nor *nor, u8 opcode,
const u8 *buf, size_t len)
{
+ if (spi_nor_protocol_is_dtr(nor->reg_proto))
+ return -EOPNOTSUPP;
+
return nor->controller_ops->write_reg(nor, opcode, buf, len);
}
static int spi_nor_controller_ops_erase(struct spi_nor *nor, loff_t offs)
{
+ if (spi_nor_protocol_is_dtr(nor->write_proto))
+ return -EOPNOTSUPP;
+
return nor->controller_ops->erase(nor, offs);
}
@@ -113,22 +194,20 @@ static ssize_t spi_nor_spimem_read_data(struct spi_nor *nor, loff_t from,
size_t len, u8 *buf)
{
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 1),
- SPI_MEM_OP_ADDR(nor->addr_width, from, 1),
- SPI_MEM_OP_DUMMY(nor->read_dummy, 1),
- SPI_MEM_OP_DATA_IN(len, buf, 1));
+ SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 0),
+ SPI_MEM_OP_ADDR(nor->addr_width, from, 0),
+ SPI_MEM_OP_DUMMY(nor->read_dummy, 0),
+ SPI_MEM_OP_DATA_IN(len, buf, 0));
bool usebouncebuf;
ssize_t nbytes;
int error;
- /* get transfer protocols. */
- op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->read_proto);
- op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->read_proto);
- op.dummy.buswidth = op.addr.buswidth;
- op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->read_proto);
+ spi_nor_spimem_setup_op(nor, &op, nor->read_proto);
/* convert the dummy cycles to the number of bytes */
op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
+ if (spi_nor_protocol_is_dtr(nor->read_proto))
+ op.dummy.nbytes *= 2;
usebouncebuf = spi_nor_spimem_bounce(nor, &op);
@@ -179,20 +258,18 @@ static ssize_t spi_nor_spimem_write_data(struct spi_nor *nor, loff_t to,
size_t len, const u8 *buf)
{
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 1),
- SPI_MEM_OP_ADDR(nor->addr_width, to, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 0),
+ SPI_MEM_OP_ADDR(nor->addr_width, to, 0),
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_OUT(len, buf, 1));
+ SPI_MEM_OP_DATA_OUT(len, buf, 0));
ssize_t nbytes;
int error;
- op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->write_proto);
- op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->write_proto);
- op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->write_proto);
-
if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second)
op.addr.nbytes = 0;
+ spi_nor_spimem_setup_op(nor, &op, nor->write_proto);
+
if (spi_nor_spimem_bounce(nor, &op))
memcpy(nor->bouncebuf, buf, op.data.nbytes);
@@ -239,11 +316,13 @@ int spi_nor_write_enable(struct spi_nor *nor)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WREN, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WREN, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_NO_DATA);
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
ret = spi_nor_controller_ops_write_reg(nor, SPINOR_OP_WREN,
@@ -268,11 +347,13 @@ int spi_nor_write_disable(struct spi_nor *nor)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WRDI, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WRDI, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_NO_DATA);
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
ret = spi_nor_controller_ops_write_reg(nor, SPINOR_OP_WRDI,
@@ -299,10 +380,12 @@ static int spi_nor_read_sr(struct spi_nor *nor, u8 *sr)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDSR, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDSR, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_IN(1, sr, 1));
+ SPI_MEM_OP_DATA_IN(1, sr, 0));
+
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
@@ -330,10 +413,12 @@ static int spi_nor_read_fsr(struct spi_nor *nor, u8 *fsr)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDFSR, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDFSR, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_IN(1, fsr, 1));
+ SPI_MEM_OP_DATA_IN(1, fsr, 0));
+
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
@@ -362,10 +447,12 @@ static int spi_nor_read_cr(struct spi_nor *nor, u8 *cr)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDCR, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDCR, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_IN(1, cr, 1));
+ SPI_MEM_OP_DATA_IN(1, cr, 0));
+
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
@@ -396,11 +483,13 @@ int spi_nor_set_4byte_addr_mode(struct spi_nor *nor, bool enable)
SPI_MEM_OP(SPI_MEM_OP_CMD(enable ?
SPINOR_OP_EN4B :
SPINOR_OP_EX4B,
- 1),
+ 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_NO_DATA);
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
ret = spi_nor_controller_ops_write_reg(nor,
@@ -432,10 +521,12 @@ static int spansion_set_4byte_addr_mode(struct spi_nor *nor, bool enable)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_BRWR, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_BRWR, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_OUT(1, nor->bouncebuf, 1));
+ SPI_MEM_OP_DATA_OUT(1, nor->bouncebuf, 0));
+
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
@@ -464,10 +555,12 @@ int spi_nor_write_ear(struct spi_nor *nor, u8 ear)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WREAR, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WREAR, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_OUT(1, nor->bouncebuf, 1));
+ SPI_MEM_OP_DATA_OUT(1, nor->bouncebuf, 0));
+
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
@@ -495,10 +588,12 @@ int spi_nor_xread_sr(struct spi_nor *nor, u8 *sr)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_XRDSR, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_XRDSR, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_IN(1, sr, 1));
+ SPI_MEM_OP_DATA_IN(1, sr, 0));
+
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
@@ -540,11 +635,13 @@ static void spi_nor_clear_sr(struct spi_nor *nor)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_CLSR, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_CLSR, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_NO_DATA);
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
ret = spi_nor_controller_ops_write_reg(nor, SPINOR_OP_CLSR,
@@ -604,11 +701,13 @@ static void spi_nor_clear_fsr(struct spi_nor *nor)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_CLFSR, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_CLFSR, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_NO_DATA);
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
+
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
ret = spi_nor_controller_ops_write_reg(nor, SPINOR_OP_CLFSR,
@@ -748,10 +847,12 @@ static int spi_nor_write_sr(struct spi_nor *nor, const u8 *sr, size_t len)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WRSR, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WRSR, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_OUT(len, sr, 1));
+ SPI_MEM_OP_DATA_OUT(len, sr, 0));
+
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
@@ -950,10 +1051,12 @@ static int spi_nor_write_sr2(struct spi_nor *nor, const u8 *sr2)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WRSR2, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WRSR2, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_OUT(1, sr2, 1));
+ SPI_MEM_OP_DATA_OUT(1, sr2, 0));
+
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
@@ -984,10 +1087,12 @@ static int spi_nor_read_sr2(struct spi_nor *nor, u8 *sr2)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDSR2, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDSR2, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_IN(1, sr2, 1));
+ SPI_MEM_OP_DATA_IN(1, sr2, 0));
+
+ spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
@@ -1015,11 +1120,13 @@ static int spi_nor_erase_chip(struct spi_nor *nor)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_CHIP_ERASE, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_CHIP_ERASE, 0),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_NO_DATA);
+ spi_nor_spimem_setup_op(nor, &op, nor->write_proto);
+
ret = spi_mem_exec_op(nor->spimem, &op);
} else {
ret = spi_nor_controller_ops_write_reg(nor,
@@ -1158,11 +1265,13 @@ static int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
if (nor->spimem) {
struct spi_mem_op op =
- SPI_MEM_OP(SPI_MEM_OP_CMD(nor->erase_opcode, 1),
- SPI_MEM_OP_ADDR(nor->addr_width, addr, 1),
+ SPI_MEM_OP(SPI_MEM_OP_CMD(nor->erase_opcode, 0),
+ SPI_MEM_OP_ADDR(nor->addr_width, addr, 0),
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_NO_DATA);
+ spi_nor_spimem_setup_op(nor, &op, nor->write_proto);
+
return spi_mem_exec_op(nor->spimem, &op);
} else if (nor->controller_ops->erase) {
return spi_nor_controller_ops_erase(nor, addr);
@@ -2272,6 +2381,7 @@ int spi_nor_hwcaps_read2cmd(u32 hwcaps)
{ SNOR_HWCAPS_READ_1_8_8, SNOR_CMD_READ_1_8_8 },
{ SNOR_HWCAPS_READ_8_8_8, SNOR_CMD_READ_8_8_8 },
{ SNOR_HWCAPS_READ_1_8_8_DTR, SNOR_CMD_READ_1_8_8_DTR },
+ { SNOR_HWCAPS_READ_8_8_8_DTR, SNOR_CMD_READ_8_8_8_DTR },
};
return spi_nor_hwcaps2cmd(hwcaps, hwcaps_read2cmd,
@@ -2288,6 +2398,7 @@ static int spi_nor_hwcaps_pp2cmd(u32 hwcaps)
{ SNOR_HWCAPS_PP_1_1_8, SNOR_CMD_PP_1_1_8 },
{ SNOR_HWCAPS_PP_1_8_8, SNOR_CMD_PP_1_8_8 },
{ SNOR_HWCAPS_PP_8_8_8, SNOR_CMD_PP_8_8_8 },
+ { SNOR_HWCAPS_PP_8_8_8_DTR, SNOR_CMD_PP_8_8_8_DTR },
};
return spi_nor_hwcaps2cmd(hwcaps, hwcaps_pp2cmd,
@@ -2336,17 +2447,17 @@ static int spi_nor_spimem_check_op(struct spi_nor *nor,
static int spi_nor_spimem_check_readop(struct spi_nor *nor,
const struct spi_nor_read_command *read)
{
- struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(read->opcode, 1),
- SPI_MEM_OP_ADDR(3, 0, 1),
- SPI_MEM_OP_DUMMY(0, 1),
- SPI_MEM_OP_DATA_IN(0, NULL, 1));
+ struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(read->opcode, 0),
+ SPI_MEM_OP_ADDR(3, 0, 0),
+ SPI_MEM_OP_DUMMY(1, 0),
+ SPI_MEM_OP_DATA_IN(1, NULL, 0));
- op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(read->proto);
- op.addr.buswidth = spi_nor_get_protocol_addr_nbits(read->proto);
- op.data.buswidth = spi_nor_get_protocol_data_nbits(read->proto);
- op.dummy.buswidth = op.addr.buswidth;
- op.dummy.nbytes = (read->num_mode_clocks + read->num_wait_states) *
- op.dummy.buswidth / 8;
+ spi_nor_spimem_setup_op(nor, &op, read->proto);
+
+ /* convert the dummy cycles to the number of bytes */
+ op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
+ if (spi_nor_protocol_is_dtr(nor->read_proto))
+ op.dummy.nbytes *= 2;
return spi_nor_spimem_check_op(nor, &op);
}
@@ -2362,14 +2473,12 @@ static int spi_nor_spimem_check_readop(struct spi_nor *nor,
static int spi_nor_spimem_check_pp(struct spi_nor *nor,
const struct spi_nor_pp_command *pp)
{
- struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(pp->opcode, 1),
- SPI_MEM_OP_ADDR(3, 0, 1),
+ struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(pp->opcode, 0),
+ SPI_MEM_OP_ADDR(3, 0, 0),
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_OUT(0, NULL, 1));
+ SPI_MEM_OP_DATA_OUT(1, NULL, 0));
- op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(pp->proto);
- op.addr.buswidth = spi_nor_get_protocol_addr_nbits(pp->proto);
- op.data.buswidth = spi_nor_get_protocol_data_nbits(pp->proto);
+ spi_nor_spimem_setup_op(nor, &op, pp->proto);
return spi_nor_spimem_check_op(nor, &op);
}
@@ -2387,12 +2496,16 @@ spi_nor_spimem_adjust_hwcaps(struct spi_nor *nor, u32 *hwcaps)
struct spi_nor_flash_parameter *params = nor->params;
unsigned int cap;
- /* DTR modes are not supported yet, mask them all. */
- *hwcaps &= ~SNOR_HWCAPS_DTR;
-
/* X-X-X modes are not supported yet, mask them all. */
*hwcaps &= ~SNOR_HWCAPS_X_X_X;
+ /*
+ * If the reset line is broken, we do not want to enter a stateful
+ * mode.
+ */
+ if (nor->flags & SNOR_F_BROKEN_RESET)
+ *hwcaps &= ~(SNOR_HWCAPS_X_X_X | SNOR_HWCAPS_X_X_X_DTR);
+
for (cap = 0; cap < sizeof(*hwcaps) * BITS_PER_BYTE; cap++) {
int rdidx, ppidx;
@@ -2647,7 +2760,7 @@ static int spi_nor_default_setup(struct spi_nor *nor,
* controller directly implements the spi_nor interface.
* Yet another reason to switch to spi-mem.
*/
- ignored_mask = SNOR_HWCAPS_X_X_X;
+ ignored_mask = SNOR_HWCAPS_X_X_X | SNOR_HWCAPS_X_X_X_DTR;
if (shared_mask & ignored_mask) {
dev_dbg(nor->dev,
"SPI n-n-n protocols are not supported.\n");
@@ -2793,11 +2906,28 @@ static void spi_nor_info_init_params(struct spi_nor *nor)
SNOR_PROTO_1_1_8);
}
+ if (info->flags & SPI_NOR_OCTAL_DTR_READ) {
+ params->hwcaps.mask |= SNOR_HWCAPS_READ_8_8_8_DTR;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_8_8_8_DTR],
+ 0, 20, SPINOR_OP_READ_FAST,
+ SNOR_PROTO_8_8_8_DTR);
+ }
+
/* Page Program settings. */
params->hwcaps.mask |= SNOR_HWCAPS_PP;
spi_nor_set_pp_settings(¶ms->page_programs[SNOR_CMD_PP],
SPINOR_OP_PP, SNOR_PROTO_1_1_1);
+ if (info->flags & SPI_NOR_OCTAL_DTR_PP) {
+ params->hwcaps.mask |= SNOR_HWCAPS_PP_8_8_8_DTR;
+ /*
+ * Since xSPI Page Program opcode is backward compatible with
+ * Legacy SPI, use Legacy SPI opcode there as well.
+ */
+ spi_nor_set_pp_settings(¶ms->page_programs[SNOR_CMD_PP_8_8_8_DTR],
+ SPINOR_OP_PP, SNOR_PROTO_8_8_8_DTR);
+ }
+
/*
* Sector Erase settings. Sort Erase Types in ascending order, with the
* smallest erase size starting at BIT(0).
@@ -2905,7 +3035,8 @@ static int spi_nor_init_params(struct spi_nor *nor)
spi_nor_manufacturer_init_params(nor);
- if ((nor->info->flags & (SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)) &&
+ if ((nor->info->flags & (SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_OCTAL_READ | SPI_NOR_OCTAL_DTR_READ)) &&
!(nor->info->flags & SPI_NOR_SKIP_SFDP))
spi_nor_sfdp_init_params(nor);
@@ -2967,7 +3098,9 @@ static int spi_nor_init(struct spi_nor *nor)
return err;
}
- if (nor->addr_width == 4 && !(nor->flags & SNOR_F_4B_OPCODES)) {
+ if (nor->addr_width == 4 &&
+ nor->read_proto != SNOR_PROTO_8_8_8_DTR &&
+ !(nor->flags & SNOR_F_4B_OPCODES)) {
/*
* If the RESET# pin isn't hooked up properly, or the system
* otherwise doesn't perform a reset command in the boot
@@ -3026,6 +3159,20 @@ static int spi_nor_set_addr_width(struct spi_nor *nor)
{
if (nor->addr_width) {
/* already configured from SFDP */
+ } else if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) {
+ /*
+ * In 8D-8D-8D mode, one byte takes half a cycle to transfer. So
+ * in this protocol an odd address width cannot be used because
+ * then the address phase would only span a cycle and a half.
+ * Half a cycle would be left over. We would then have to start
+ * the dummy phase in the middle of a cycle and so too the data
+ * phase, and we will end the transaction with half a cycle left
+ * over.
+ *
+ * Force all 8D-8D-8D flashes to use an address width of 4 to
+ * avoid this situation.
+ */
+ nor->addr_width = 4;
} else if (nor->info->addr_width) {
nor->addr_width = nor->info->addr_width;
} else if (nor->mtd.size > 0x1000000) {
@@ -3254,23 +3401,28 @@ EXPORT_SYMBOL_GPL(spi_nor_scan);
static int spi_nor_create_read_dirmap(struct spi_nor *nor)
{
struct spi_mem_dirmap_info info = {
- .op_tmpl = SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 1),
- SPI_MEM_OP_ADDR(nor->addr_width, 0, 1),
- SPI_MEM_OP_DUMMY(nor->read_dummy, 1),
- SPI_MEM_OP_DATA_IN(0, NULL, 1)),
+ .op_tmpl = SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 0),
+ SPI_MEM_OP_ADDR(nor->addr_width, 0, 0),
+ SPI_MEM_OP_DUMMY(nor->read_dummy, 0),
+ SPI_MEM_OP_DATA_IN(0, NULL, 0)),
.offset = 0,
.length = nor->mtd.size,
};
struct spi_mem_op *op = &info.op_tmpl;
- /* get transfer protocols. */
- op->cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->read_proto);
- op->addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->read_proto);
- op->dummy.buswidth = op->addr.buswidth;
- op->data.buswidth = spi_nor_get_protocol_data_nbits(nor->read_proto);
+ spi_nor_spimem_setup_op(nor, op, nor->read_proto);
/* convert the dummy cycles to the number of bytes */
op->dummy.nbytes = (nor->read_dummy * op->dummy.buswidth) / 8;
+ if (spi_nor_protocol_is_dtr(nor->read_proto))
+ op->dummy.nbytes *= 2;
+
+ /*
+ * Since spi_nor_spimem_setup_op() only sets buswidth when the number
+ * of data bytes is non-zero, the data buswidth won't be set here. So,
+ * do it explicitly.
+ */
+ op->data.buswidth = spi_nor_get_protocol_data_nbits(nor->read_proto);
nor->dirmap.rdesc = devm_spi_mem_dirmap_create(nor->dev, nor->spimem,
&info);
@@ -3280,24 +3432,27 @@ static int spi_nor_create_read_dirmap(struct spi_nor *nor)
static int spi_nor_create_write_dirmap(struct spi_nor *nor)
{
struct spi_mem_dirmap_info info = {
- .op_tmpl = SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 1),
- SPI_MEM_OP_ADDR(nor->addr_width, 0, 1),
+ .op_tmpl = SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 0),
+ SPI_MEM_OP_ADDR(nor->addr_width, 0, 0),
SPI_MEM_OP_NO_DUMMY,
- SPI_MEM_OP_DATA_OUT(0, NULL, 1)),
+ SPI_MEM_OP_DATA_OUT(0, NULL, 0)),
.offset = 0,
.length = nor->mtd.size,
};
struct spi_mem_op *op = &info.op_tmpl;
- /* get transfer protocols. */
- op->cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->write_proto);
- op->addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->write_proto);
- op->dummy.buswidth = op->addr.buswidth;
- op->data.buswidth = spi_nor_get_protocol_data_nbits(nor->write_proto);
-
if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second)
op->addr.nbytes = 0;
+ spi_nor_spimem_setup_op(nor, op, nor->write_proto);
+
+ /*
+ * Since spi_nor_spimem_setup_op() only sets buswidth when the number
+ * of data bytes is non-zero, the data buswidth won't be set here. So,
+ * do it explicitly.
+ */
+ op->data.buswidth = spi_nor_get_protocol_data_nbits(nor->write_proto);
+
nor->dirmap.wdesc = devm_spi_mem_dirmap_create(nor->dev, nor->spimem,
&info);
return PTR_ERR_OR_ZERO(nor->dirmap.wdesc);
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index 6f2f6b27173f..5d95b4183a33 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -62,6 +62,7 @@ enum spi_nor_read_command_index {
SNOR_CMD_READ_1_8_8,
SNOR_CMD_READ_8_8_8,
SNOR_CMD_READ_1_8_8_DTR,
+ SNOR_CMD_READ_8_8_8_DTR,
SNOR_CMD_READ_MAX
};
@@ -78,6 +79,7 @@ enum spi_nor_pp_command_index {
SNOR_CMD_PP_1_1_8,
SNOR_CMD_PP_1_8_8,
SNOR_CMD_PP_8_8_8,
+ SNOR_CMD_PP_8_8_8_DTR,
SNOR_CMD_PP_MAX
};
@@ -311,6 +313,8 @@ struct flash_info {
* BP3 is bit 6 of status register.
* Must be used with SPI_NOR_4BIT_BP.
*/
+#define SPI_NOR_OCTAL_DTR_READ BIT(19) /* Flash supports octal DTR Read. */
+#define SPI_NOR_OCTAL_DTR_PP BIT(20) /* Flash supports Octal DTR Page Program */
/* Part specific fixup hooks. */
const struct spi_nor_fixups *fixups;
@@ -399,6 +403,9 @@ extern const struct spi_nor_manufacturer spi_nor_winbond;
extern const struct spi_nor_manufacturer spi_nor_xilinx;
extern const struct spi_nor_manufacturer spi_nor_xmc;
+void spi_nor_spimem_setup_op(const struct spi_nor *nor,
+ struct spi_mem_op *op,
+ const enum spi_nor_protocol proto);
int spi_nor_write_enable(struct spi_nor *nor);
int spi_nor_write_disable(struct spi_nor *nor);
int spi_nor_set_4byte_addr_mode(struct spi_nor *nor, bool enable);
diff --git a/drivers/mtd/spi-nor/sfdp.c b/drivers/mtd/spi-nor/sfdp.c
index e2a43d39eb5f..21fa9ab78eae 100644
--- a/drivers/mtd/spi-nor/sfdp.c
+++ b/drivers/mtd/spi-nor/sfdp.c
@@ -1047,9 +1047,16 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,
}
/* 4BAIT is the only SFDP table that indicates page program support. */
- if (pp_hwcaps & SNOR_HWCAPS_PP)
+ if (pp_hwcaps & SNOR_HWCAPS_PP) {
spi_nor_set_pp_settings(¶ms_pp[SNOR_CMD_PP],
SPINOR_OP_PP_4B, SNOR_PROTO_1_1_1);
+ /*
+ * Since xSPI Page Program opcode is backward compatible with
+ * Legacy SPI, use Legacy SPI opcode there as well.
+ */
+ spi_nor_set_pp_settings(¶ms_pp[SNOR_CMD_PP_8_8_8_DTR],
+ SPINOR_OP_PP_4B, SNOR_PROTO_8_8_8_DTR);
+ }
if (pp_hwcaps & SNOR_HWCAPS_PP_1_1_4)
spi_nor_set_pp_settings(¶ms_pp[SNOR_CMD_PP_1_1_4],
SPINOR_OP_PP_1_1_4_4B,
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 60bac2c0ec45..cd549042c53d 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -182,6 +182,7 @@ enum spi_nor_protocol {
SNOR_PROTO_1_2_2_DTR = SNOR_PROTO_DTR(1, 2, 2),
SNOR_PROTO_1_4_4_DTR = SNOR_PROTO_DTR(1, 4, 4),
SNOR_PROTO_1_8_8_DTR = SNOR_PROTO_DTR(1, 8, 8),
+ SNOR_PROTO_8_8_8_DTR = SNOR_PROTO_DTR(8, 8, 8),
};
static inline bool spi_nor_protocol_is_dtr(enum spi_nor_protocol proto)
@@ -228,7 +229,7 @@ struct spi_nor_hwcaps {
* then Quad SPI protocols before Dual SPI protocols, Fast Read and lastly
* (Slow) Read.
*/
-#define SNOR_HWCAPS_READ_MASK GENMASK(14, 0)
+#define SNOR_HWCAPS_READ_MASK GENMASK(15, 0)
#define SNOR_HWCAPS_READ BIT(0)
#define SNOR_HWCAPS_READ_FAST BIT(1)
#define SNOR_HWCAPS_READ_1_1_1_DTR BIT(2)
@@ -245,11 +246,12 @@ struct spi_nor_hwcaps {
#define SNOR_HWCAPS_READ_4_4_4 BIT(9)
#define SNOR_HWCAPS_READ_1_4_4_DTR BIT(10)
-#define SNOR_HWCAPS_READ_OCTAL GENMASK(14, 11)
+#define SNOR_HWCAPS_READ_OCTAL GENMASK(15, 11)
#define SNOR_HWCAPS_READ_1_1_8 BIT(11)
#define SNOR_HWCAPS_READ_1_8_8 BIT(12)
#define SNOR_HWCAPS_READ_8_8_8 BIT(13)
#define SNOR_HWCAPS_READ_1_8_8_DTR BIT(14)
+#define SNOR_HWCAPS_READ_8_8_8_DTR BIT(15)
/*
* Page Program capabilities.
@@ -260,18 +262,19 @@ struct spi_nor_hwcaps {
* JEDEC/SFDP standard to define them. Also at this moment no SPI flash memory
* implements such commands.
*/
-#define SNOR_HWCAPS_PP_MASK GENMASK(22, 16)
-#define SNOR_HWCAPS_PP BIT(16)
+#define SNOR_HWCAPS_PP_MASK GENMASK(23, 16)
+#define SNOR_HWCAPS_PP BIT(16)
-#define SNOR_HWCAPS_PP_QUAD GENMASK(19, 17)
-#define SNOR_HWCAPS_PP_1_1_4 BIT(17)
-#define SNOR_HWCAPS_PP_1_4_4 BIT(18)
-#define SNOR_HWCAPS_PP_4_4_4 BIT(19)
+#define SNOR_HWCAPS_PP_QUAD GENMASK(19, 17)
+#define SNOR_HWCAPS_PP_1_1_4 BIT(17)
+#define SNOR_HWCAPS_PP_1_4_4 BIT(18)
+#define SNOR_HWCAPS_PP_4_4_4 BIT(19)
-#define SNOR_HWCAPS_PP_OCTAL GENMASK(22, 20)
-#define SNOR_HWCAPS_PP_1_1_8 BIT(20)
-#define SNOR_HWCAPS_PP_1_8_8 BIT(21)
-#define SNOR_HWCAPS_PP_8_8_8 BIT(22)
+#define SNOR_HWCAPS_PP_OCTAL GENMASK(23, 20)
+#define SNOR_HWCAPS_PP_1_1_8 BIT(20)
+#define SNOR_HWCAPS_PP_1_8_8 BIT(21)
+#define SNOR_HWCAPS_PP_8_8_8 BIT(22)
+#define SNOR_HWCAPS_PP_8_8_8_DTR BIT(23)
#define SNOR_HWCAPS_X_X_X (SNOR_HWCAPS_READ_2_2_2 | \
SNOR_HWCAPS_READ_4_4_4 | \
@@ -279,10 +282,14 @@ struct spi_nor_hwcaps {
SNOR_HWCAPS_PP_4_4_4 | \
SNOR_HWCAPS_PP_8_8_8)
+#define SNOR_HWCAPS_X_X_X_DTR (SNOR_HWCAPS_READ_8_8_8_DTR | \
+ SNOR_HWCAPS_PP_8_8_8_DTR)
+
#define SNOR_HWCAPS_DTR (SNOR_HWCAPS_READ_1_1_1_DTR | \
SNOR_HWCAPS_READ_1_2_2_DTR | \
SNOR_HWCAPS_READ_1_4_4_DTR | \
- SNOR_HWCAPS_READ_1_8_8_DTR)
+ SNOR_HWCAPS_READ_1_8_8_DTR | \
+ SNOR_HWCAPS_READ_8_8_8_DTR)
#define SNOR_HWCAPS_ALL (SNOR_HWCAPS_READ_MASK | \
SNOR_HWCAPS_PP_MASK)
@@ -318,6 +325,22 @@ struct spi_nor_controller_ops {
int (*erase)(struct spi_nor *nor, loff_t offs);
};
+/**
+ * enum spi_nor_cmd_ext - describes the command opcode extension in DTR mode
+ * @SPI_NOR_EXT_NONE: no extension. This is the default, and is used in Legacy
+ * SPI mode
+ * @SPI_NOR_EXT_REPEAT: the extension is same as the opcode
+ * @SPI_NOR_EXT_INVERT: the extension is the bitwise inverse of the opcode
+ * @SPI_NOR_EXT_HEX: the extension is any hex value. The command and opcode
+ * combine to form a 16-bit opcode.
+ */
+enum spi_nor_cmd_ext {
+ SPI_NOR_EXT_NONE = 0,
+ SPI_NOR_EXT_REPEAT,
+ SPI_NOR_EXT_INVERT,
+ SPI_NOR_EXT_HEX,
+};
+
/*
* Forward declarations that are used internally by the core and manufacturer
* drivers.
@@ -345,6 +368,7 @@ struct spi_nor_flash_parameter;
* @program_opcode: the program opcode
* @sst_write_second: used by the SST write operation
* @flags: flag options for the current SPI NOR (SNOR_F_*)
+ * @cmd_ext_type: the command opcode extension type for DTR mode.
* @read_proto: the SPI protocol for read operations
* @write_proto: the SPI protocol for write operations
* @reg_proto: the SPI protocol for read_reg/write_reg/erase operations
@@ -376,6 +400,7 @@ struct spi_nor {
enum spi_nor_protocol reg_proto;
bool sst_write_second;
u32 flags;
+ enum spi_nor_cmd_ext cmd_ext_type;
const struct spi_nor_controller_ops *controller_ops;
--
2.28.0
More information about the linux-mtd
mailing list