[PATCH v3 1/3] UBI: Do not zero out EC and VID on ECC-ed NOR flashes

Pratyush Yadav p.yadav at ti.com
Tue Dec 1 05:27:09 EST 2020


For NOR flashes EC and VID are zeroed out before an erase is issued to
make sure UBI does not mistakenly treat the PEB as used and associate it
with an LEB.

But on some flashes, like the Cypress Semper S28 SPI NOR flash family,
multi-pass page programming is not allowed on the default ECC scheme.
This means zeroing out these magic numbers will result in the flash
throwing a page programming error.

Do not zero out EC and VID for such flashes. A writesize > 1 is an
indication of an ECC-ed flash.

Signed-off-by: Pratyush Yadav <p.yadav at ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus at microchip.com>
---

Notes:
    No changes in v3.
    
    Changes in v2:
    
    - Use mtd->writesize to check if multi-pass programming can be done
      instead of using MTD_NO_MULTI_PASS_WRITE.
    - Remove the assertion that a NOR flash most have writesize of 1.

 drivers/mtd/ubi/build.c | 4 +---
 drivers/mtd/ubi/io.c    | 9 ++++++++-
 2 files changed, 9 insertions(+), 4 deletions(-)

diff --git a/drivers/mtd/ubi/build.c b/drivers/mtd/ubi/build.c
index e85b04e9716b..25fd7816b1f4 100644
--- a/drivers/mtd/ubi/build.c
+++ b/drivers/mtd/ubi/build.c
@@ -628,10 +628,8 @@ static int io_init(struct ubi_device *ubi, int max_beb_per1024)
 		ubi->bad_peb_limit = get_bad_peb_limit(ubi, max_beb_per1024);
 	}
 
-	if (ubi->mtd->type == MTD_NORFLASH) {
-		ubi_assert(ubi->mtd->writesize == 1);
+	if (ubi->mtd->type == MTD_NORFLASH)
 		ubi->nor_flash = 1;
-	}
 
 	ubi->min_io_size = ubi->mtd->writesize;
 	ubi->hdrs_min_io_size = ubi->mtd->writesize >> ubi->mtd->subpage_sft;
diff --git a/drivers/mtd/ubi/io.c b/drivers/mtd/ubi/io.c
index 14d890b00d2c..2f3312c31e51 100644
--- a/drivers/mtd/ubi/io.c
+++ b/drivers/mtd/ubi/io.c
@@ -535,7 +535,14 @@ int ubi_io_sync_erase(struct ubi_device *ubi, int pnum, int torture)
 		return -EROFS;
 	}
 
-	if (ubi->nor_flash) {
+	/*
+	 * If the flash is ECC-ed then we have to erase the ECC block before we
+	 * can write to it. But the write is in preparation to an erase in the
+	 * first place. This means we cannot zero out EC and VID before the
+	 * erase and we just have to hope the flash starts erasing from the
+	 * start of the page.
+	 */
+	if (ubi->nor_flash && ubi->mtd->writesize == 1) {
 		err = nor_erase_prepare(ubi, pnum);
 		if (err)
 			return err;
-- 
2.28.0




More information about the linux-mtd mailing list