[PATCH v4 16/20] mtd: spi-nor: Rename CR_QUAD_EN_SPAN to SR2_QUAD_EN_BIT1

Vignesh Raghavendra vigneshr at ti.com
Tue Nov 5 21:45:37 PST 2019



On 02/11/19 4:53 PM, Tudor.Ambarus at microchip.com wrote:
> From: Tudor Ambarus <tudor.ambarus at microchip.com>
> 
> JEDEC Basic Flash Parameter Table, 15th DWORD, bits 22:20,
> refers to this bit as "bit 1 of the status register 2".
> Rename the macro accordingly.
> 
> Signed-off-by: Tudor Ambarus <tudor.ambarus at microchip.com>

Reviewed-by: Vignesh Raghavendra <vigneshr at ti.com>

Regards
Vignesh

> ---
>  drivers/mtd/spi-nor/spi-nor.c | 10 +++++-----
>  include/linux/mtd/spi-nor.h   |  4 +---
>  2 files changed, 6 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
> index 8f11c00e8ae5..e367a4862ec1 100644
> --- a/drivers/mtd/spi-nor/spi-nor.c
> +++ b/drivers/mtd/spi-nor/spi-nor.c
> @@ -1026,7 +1026,7 @@ static int spi_nor_write_16bit_sr_and_check(struct spi_nor *nor, u8 sr1)
>  		 * Write Status (01h) command is available just for the cases
>  		 * in which the QE bit is described in SR2 at BIT(1).
>  		 */
> -		sr_cr[1] = CR_QUAD_EN_SPAN;
> +		sr_cr[1] = SR2_QUAD_EN_BIT1;
>  	} else {
>  		sr_cr[1] = 0;
>  	}
> @@ -2074,7 +2074,7 @@ static int spansion_no_read_cr_quad_enable(struct spi_nor *nor)
>  	if (ret)
>  		return ret;
>  
> -	sr_cr[1] = CR_QUAD_EN_SPAN;
> +	sr_cr[1] = SR2_QUAD_EN_BIT1;
>  
>  	ret = spi_nor_write_sr(nor, sr_cr, 2);
>  	if (ret)
> @@ -2118,10 +2118,10 @@ static int spansion_read_cr_quad_enable(struct spi_nor *nor)
>  	if (ret)
>  		return ret;
>  
> -	if (sr_cr[1] & CR_QUAD_EN_SPAN)
> +	if (sr_cr[1] & SR2_QUAD_EN_BIT1)
>  		return 0;
>  
> -	sr_cr[1] |= CR_QUAD_EN_SPAN;
> +	sr_cr[1] |= SR2_QUAD_EN_BIT1;
>  
>  	/* Keep the current value of the Status Register. */
>  	ret = spi_nor_read_sr(nor, sr_cr);
> @@ -2256,7 +2256,7 @@ static int spi_nor_spansion_clear_sr_bp(struct spi_nor *nor)
>  	 * When the configuration register Quad Enable bit is one, only the
>  	 * Write Status (01h) command with two data bytes may be used.
>  	 */
> -	if (sr_cr[1] & CR_QUAD_EN_SPAN) {
> +	if (sr_cr[1] & SR2_QUAD_EN_BIT1) {
>  		ret = spi_nor_read_sr(nor, sr_cr);
>  		if (ret)
>  			return ret;
> diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
> index d6ec55cc6d97..f626e0e52909 100644
> --- a/include/linux/mtd/spi-nor.h
> +++ b/include/linux/mtd/spi-nor.h
> @@ -144,10 +144,8 @@
>  #define FSR_P_ERR		BIT(4)	/* Program operation status */
>  #define FSR_PT_ERR		BIT(1)	/* Protection error bit */
>  
> -/* Configuration Register bits. */
> -#define CR_QUAD_EN_SPAN		BIT(1)	/* Spansion Quad I/O */
> -
>  /* Status Register 2 bits. */
> +#define SR2_QUAD_EN_BIT1	BIT(1)
>  #define SR2_QUAD_EN_BIT7	BIT(7)
>  
>  /* Supported SPI protocols */
> 

-- 
Regards
Vignesh



More information about the linux-mtd mailing list