[PATCHv6 2/2] mtd: spi-nor: cadence-quadspi: add reset control

Dinh Nguyen dinguyen at kernel.org
Thu Jun 13 04:31:38 PDT 2019

Get the reset control properties for the QSPI controller and bring them
out of reset. Most will have just one reset bit, but there is an additional
OCP reset bit that is used ECC. The OCP reset bit will also need to get
de-asserted as well. [1]

The reason this patch is needed is in the case where a bootloader leaves
the QSPI controller in a reset state, or a state where init cannot occur
successfully, the patch will put the QSPI controller into a clean state.

[1] https://www.intel.com/content/www/us/en/programmable/hps/arria-10/hps.html#reg_soc_top/sfo1429890575955.html

Suggested-by: Tien-Fong Chee <tien.fong.chee at intel.com>
Signed-off-by: Dinh Nguyen <dinguyen at kernel.org>
v6: no need to check for reset pointer in assert/deassert as the call to
    assert/deassert is already doing the checking
v5: remove udelay(not needed) on tested hardware
    group reset assert/deassert together
    update commit message with reasoning for patch
v4: fix compile error
v3: return full error by using PTR_ERR(rtsc)
    move reset control calls until after the clock enables
    use udelay(2) to be safe
    Add optional OCP(Open Core Protocol) reset signal
v2: use devm_reset_control_get_optional_exclusive
    print an error message
    return -EPROBE_DEFER
 drivers/mtd/spi-nor/cadence-quadspi.c | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/drivers/mtd/spi-nor/cadence-quadspi.c b/drivers/mtd/spi-nor/cadence-quadspi.c
index 792628750eec..732323c2adb1 100644
--- a/drivers/mtd/spi-nor/cadence-quadspi.c
+++ b/drivers/mtd/spi-nor/cadence-quadspi.c
@@ -34,6 +34,7 @@
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
+#include <linux/reset.h>
 #include <linux/sched.h>
 #include <linux/spi/spi.h>
 #include <linux/timer.h>
@@ -1336,6 +1337,8 @@ static int cqspi_probe(struct platform_device *pdev)
 	struct cqspi_st *cqspi;
 	struct resource *res;
 	struct resource *res_ahb;
+	struct reset_control *rstc;
+	struct reset_control *rstc_ocp;
 	const struct cqspi_driver_platdata *ddata;
 	int ret;
 	int irq;
@@ -1402,6 +1405,25 @@ static int cqspi_probe(struct platform_device *pdev)
 		goto probe_clk_failed;
+	/* Obtain QSPI reset control */
+	rstc = devm_reset_control_get_optional_exclusive(dev, "qspi");
+	if (IS_ERR(rstc)) {
+		dev_err(dev, "Cannot get QSPI reset.\n");
+		return PTR_ERR(rstc);
+	}
+	rstc_ocp = devm_reset_control_get_optional_exclusive(dev, "qspi-ocp");
+	if (IS_ERR(rstc_ocp)) {
+		dev_err(dev, "Cannot get QSPI OCP reset.\n");
+		return PTR_ERR(rstc_ocp);
+	}
+	reset_control_assert(rstc);
+	reset_control_deassert(rstc);
+	reset_control_assert(rstc_ocp);
+	reset_control_deassert(rstc_ocp);
 	cqspi->master_ref_clk_hz = clk_get_rate(cqspi->clk);
 	ddata  = of_device_get_match_data(dev);
 	if (ddata && (ddata->quirks & CQSPI_NEEDS_WR_DELAY))

More information about the linux-mtd mailing list