[PATCH v5 2/3] mtd: nand: vf610_nfc: remove old hooks
Stefan Agner
stefan at agner.ch
Mon Feb 26 13:18:54 PST 2018
Now that the driver is using ->exec_op(), remove the old
hooks.
Signed-off-by: Stefan Agner <stefan at agner.ch>
---
drivers/mtd/nand/raw/vf610_nfc.c | 269 ---------------------------------------
1 file changed, 269 deletions(-)
diff --git a/drivers/mtd/nand/raw/vf610_nfc.c b/drivers/mtd/nand/raw/vf610_nfc.c
index 9d1fb6df0e22..884707618690 100644
--- a/drivers/mtd/nand/raw/vf610_nfc.c
+++ b/drivers/mtd/nand/raw/vf610_nfc.c
@@ -59,21 +59,6 @@
#define OOB_64 0x0040
#define OOB_MAX 0x0100
-/*
- * NFC_CMD2[CODE] values. See section:
- * - 31.4.7 Flash Command Code Description, Vybrid manual
- * - 23.8.6 Flash Command Sequencer, MPC5125 manual
- *
- * Briefly these are bitmasks of controller cycles.
- */
-#define READ_PAGE_CMD_CODE 0x7EE0
-#define READ_ONFI_PARAM_CMD_CODE 0x4860
-#define PROGRAM_PAGE_CMD_CODE 0x7FC0
-#define ERASE_CMD_CODE 0x4EC0
-#define READ_ID_CMD_CODE 0x4804
-#define RESET_CMD_CODE 0x4040
-#define STATUS_READ_CMD_CODE 0x4068
-
/* NFC_CMD2[CODE] controller cycle bit masks */
#define COMMAND_CMD_BYTE1 BIT(14)
#define COMMAND_CAR_BYTE1 BIT(13)
@@ -161,13 +146,6 @@
#define ECC_STATUS_MASK 0x80
#define ECC_STATUS_ERR_COUNT 0x3F
-enum vf610_nfc_alt_buf {
- ALT_BUF_DATA = 0,
- ALT_BUF_ID = 1,
- ALT_BUF_STAT = 2,
- ALT_BUF_ONFI = 3,
-};
-
enum vf610_nfc_variant {
NFC_VFC610 = 1,
};
@@ -177,13 +155,9 @@ struct vf610_nfc {
struct device *dev;
void __iomem *regs;
struct completion cmd_done;
- uint buf_offset;
- int write_sz;
/* Status and ID are in alternate locations. */
- enum vf610_nfc_alt_buf alt_buf;
enum vf610_nfc_variant variant;
struct clk *clk;
- bool use_hw_ecc;
/*
* Indicate that user data is accessed (full page/oob). This is
* useful to indicate the driver whether to swap byte endianness.
@@ -230,20 +204,6 @@ static inline void vf610_nfc_set_field(struct vf610_nfc *nfc, u32 reg,
(vf610_nfc_read(nfc, reg) & (~mask)) | val << shift);
}
-static inline void vf610_nfc_memcpy(void *dst, const void __iomem *src,
- size_t n)
-{
- /*
- * Use this accessor for the internal SRAM buffers. On the ARM
- * Freescale Vybrid SoC it's known that the driver can treat
- * the SRAM buffer as if it's memory. Other platform might need
- * to treat the buffers differently.
- *
- * For the time being, use memcpy
- */
- memcpy(dst, src, n);
-}
-
static inline bool vf610_nfc_kernel_is_little_endian(void)
{
#ifdef __LITTLE_ENDIAN
@@ -351,53 +311,6 @@ static void vf610_nfc_done(struct vf610_nfc *nfc)
vf610_nfc_clear_status(nfc);
}
-static u8 vf610_nfc_get_id(struct vf610_nfc *nfc, int col)
-{
- u32 flash_id;
-
- if (col < 4) {
- flash_id = vf610_nfc_read(nfc, NFC_FLASH_STATUS1);
- flash_id >>= (3 - col) * 8;
- } else {
- flash_id = vf610_nfc_read(nfc, NFC_FLASH_STATUS2);
- flash_id >>= 24;
- }
-
- return flash_id & 0xff;
-}
-
-static u8 vf610_nfc_get_status(struct vf610_nfc *nfc)
-{
- return vf610_nfc_read(nfc, NFC_FLASH_STATUS2) & STATUS_BYTE1_MASK;
-}
-
-static void vf610_nfc_send_command(struct vf610_nfc *nfc, u32 cmd_byte1,
- u32 cmd_code)
-{
- u32 tmp;
-
- vf610_nfc_clear_status(nfc);
-
- tmp = vf610_nfc_read(nfc, NFC_FLASH_CMD2);
- tmp &= ~(CMD_BYTE1_MASK | CMD_CODE_MASK | BUFNO_MASK);
- tmp |= cmd_byte1 << CMD_BYTE1_SHIFT;
- tmp |= cmd_code << CMD_CODE_SHIFT;
- vf610_nfc_write(nfc, NFC_FLASH_CMD2, tmp);
-}
-
-static void vf610_nfc_send_commands(struct vf610_nfc *nfc, u32 cmd_byte1,
- u32 cmd_byte2, u32 cmd_code)
-{
- u32 tmp;
-
- vf610_nfc_send_command(nfc, cmd_byte1, cmd_code);
-
- tmp = vf610_nfc_read(nfc, NFC_FLASH_CMD1);
- tmp &= ~CMD_BYTE2_MASK;
- tmp |= cmd_byte2 << CMD_BYTE2_SHIFT;
- vf610_nfc_write(nfc, NFC_FLASH_CMD1, tmp);
-}
-
static irqreturn_t vf610_nfc_irq(int irq, void *data)
{
struct mtd_info *mtd = data;
@@ -409,19 +322,6 @@ static irqreturn_t vf610_nfc_irq(int irq, void *data)
return IRQ_HANDLED;
}
-static void vf610_nfc_addr_cycle(struct vf610_nfc *nfc, int column, int page)
-{
- if (column != -1) {
- if (nfc->chip.options & NAND_BUSWIDTH_16)
- column = column / 2;
- vf610_nfc_set_field(nfc, NFC_COL_ADDR, COL_ADDR_MASK,
- COL_ADDR_SHIFT, column);
- }
- if (page != -1)
- vf610_nfc_set_field(nfc, NFC_ROW_ADDR, ROW_ADDR_MASK,
- ROW_ADDR_SHIFT, page);
-}
-
static inline void vf610_nfc_ecc_mode(struct vf610_nfc *nfc, int ecc_mode)
{
vf610_nfc_set_field(nfc, NFC_FLASH_CONFIG,
@@ -434,169 +334,6 @@ static inline void vf610_nfc_transfer_size(struct vf610_nfc *nfc, int size)
vf610_nfc_write(nfc, NFC_SECTOR_SIZE, size);
}
-static void vf610_nfc_command(struct mtd_info *mtd, unsigned command,
- int column, int page)
-{
- struct vf610_nfc *nfc = mtd_to_nfc(mtd);
- int trfr_sz = nfc->chip.options & NAND_BUSWIDTH_16 ? 1 : 0;
-
- nfc->buf_offset = max(column, 0);
- nfc->alt_buf = ALT_BUF_DATA;
-
- switch (command) {
- case NAND_CMD_SEQIN:
- /* Use valid column/page from preread... */
- vf610_nfc_addr_cycle(nfc, column, page);
- nfc->buf_offset = 0;
-
- /*
- * SEQIN => data => PAGEPROG sequence is done by the controller
- * hence we do not need to issue the command here...
- */
- return;
- case NAND_CMD_PAGEPROG:
- trfr_sz += nfc->write_sz;
- vf610_nfc_transfer_size(nfc, trfr_sz);
- vf610_nfc_send_commands(nfc, NAND_CMD_SEQIN,
- command, PROGRAM_PAGE_CMD_CODE);
- if (nfc->use_hw_ecc)
- vf610_nfc_ecc_mode(nfc, nfc->ecc_mode);
- else
- vf610_nfc_ecc_mode(nfc, ECC_BYPASS);
- break;
-
- case NAND_CMD_RESET:
- vf610_nfc_transfer_size(nfc, 0);
- vf610_nfc_send_command(nfc, command, RESET_CMD_CODE);
- break;
-
- case NAND_CMD_READOOB:
- trfr_sz += mtd->oobsize;
- column = mtd->writesize;
- vf610_nfc_transfer_size(nfc, trfr_sz);
- vf610_nfc_send_commands(nfc, NAND_CMD_READ0,
- NAND_CMD_READSTART, READ_PAGE_CMD_CODE);
- vf610_nfc_addr_cycle(nfc, column, page);
- vf610_nfc_ecc_mode(nfc, ECC_BYPASS);
- break;
-
- case NAND_CMD_READ0:
- trfr_sz += mtd->writesize + mtd->oobsize;
- vf610_nfc_transfer_size(nfc, trfr_sz);
- vf610_nfc_send_commands(nfc, NAND_CMD_READ0,
- NAND_CMD_READSTART, READ_PAGE_CMD_CODE);
- vf610_nfc_addr_cycle(nfc, column, page);
- vf610_nfc_ecc_mode(nfc, nfc->ecc_mode);
- break;
-
- case NAND_CMD_PARAM:
- nfc->alt_buf = ALT_BUF_ONFI;
- trfr_sz = 3 * sizeof(struct nand_onfi_params);
- vf610_nfc_transfer_size(nfc, trfr_sz);
- vf610_nfc_send_command(nfc, command, READ_ONFI_PARAM_CMD_CODE);
- vf610_nfc_addr_cycle(nfc, -1, column);
- vf610_nfc_ecc_mode(nfc, ECC_BYPASS);
- break;
-
- case NAND_CMD_ERASE1:
- vf610_nfc_transfer_size(nfc, 0);
- vf610_nfc_send_commands(nfc, command,
- NAND_CMD_ERASE2, ERASE_CMD_CODE);
- vf610_nfc_addr_cycle(nfc, column, page);
- break;
-
- case NAND_CMD_READID:
- nfc->alt_buf = ALT_BUF_ID;
- nfc->buf_offset = 0;
- vf610_nfc_transfer_size(nfc, 0);
- vf610_nfc_send_command(nfc, command, READ_ID_CMD_CODE);
- vf610_nfc_addr_cycle(nfc, -1, column);
- break;
-
- case NAND_CMD_STATUS:
- nfc->alt_buf = ALT_BUF_STAT;
- vf610_nfc_transfer_size(nfc, 0);
- vf610_nfc_send_command(nfc, command, STATUS_READ_CMD_CODE);
- break;
- default:
- return;
- }
-
- vf610_nfc_done(nfc);
-
- nfc->use_hw_ecc = false;
- nfc->write_sz = 0;
-}
-
-static void vf610_nfc_read_buf(struct mtd_info *mtd, u_char *buf, int len)
-{
- struct vf610_nfc *nfc = mtd_to_nfc(mtd);
- uint c = nfc->buf_offset;
-
- /* Alternate buffers are only supported through read_byte */
- WARN_ON(nfc->alt_buf);
-
- vf610_nfc_memcpy(buf, nfc->regs + NFC_MAIN_AREA(0) + c, len);
-
- nfc->buf_offset += len;
-}
-
-static void vf610_nfc_write_buf(struct mtd_info *mtd, const uint8_t *buf,
- int len)
-{
- struct vf610_nfc *nfc = mtd_to_nfc(mtd);
- uint c = nfc->buf_offset;
- uint l;
-
- l = min_t(uint, len, mtd->writesize + mtd->oobsize - c);
- vf610_nfc_memcpy(nfc->regs + NFC_MAIN_AREA(0) + c, buf, l);
-
- nfc->write_sz += l;
- nfc->buf_offset += l;
-}
-
-static uint8_t vf610_nfc_read_byte(struct mtd_info *mtd)
-{
- struct vf610_nfc *nfc = mtd_to_nfc(mtd);
- u8 tmp;
- uint c = nfc->buf_offset;
-
- switch (nfc->alt_buf) {
- case ALT_BUF_ID:
- tmp = vf610_nfc_get_id(nfc, c);
- break;
- case ALT_BUF_STAT:
- tmp = vf610_nfc_get_status(nfc);
- break;
-#ifdef __LITTLE_ENDIAN
- case ALT_BUF_ONFI:
- /* Reverse byte since the controller uses big endianness */
- c = nfc->buf_offset ^ 0x3;
- /* fall-through */
-#endif
- default:
- tmp = *((u8 *)(nfc->regs + NFC_MAIN_AREA(0) + c));
- break;
- }
- nfc->buf_offset++;
- return tmp;
-}
-
-static u16 vf610_nfc_read_word(struct mtd_info *mtd)
-{
- u16 tmp;
-
- vf610_nfc_read_buf(mtd, (u_char *)&tmp, sizeof(tmp));
- return tmp;
-}
-
-/* If not provided, upper layers apply a fixed delay. */
-static int vf610_nfc_dev_ready(struct mtd_info *mtd)
-{
- /* NFC handles R/B internally; always ready. */
- return 1;
-}
-
static inline void vf610_nfc_run(struct vf610_nfc *nfc, u32 col, u32 row,
u32 cmd1, u32 cmd2, u32 trfr_sz)
{
@@ -1062,12 +799,6 @@ static int vf610_nfc_probe(struct platform_device *pdev)
goto err_disable_clk;
}
- chip->dev_ready = vf610_nfc_dev_ready;
- chip->cmdfunc = vf610_nfc_command;
- chip->read_byte = vf610_nfc_read_byte;
- chip->read_word = vf610_nfc_read_word;
- chip->read_buf = vf610_nfc_read_buf;
- chip->write_buf = vf610_nfc_write_buf;
chip->exec_op = vf610_nfc_exec_op;
chip->select_chip = vf610_nfc_select_chip;
chip->onfi_set_features = nand_onfi_get_set_features_notsupp;
--
2.16.2
More information about the linux-mtd
mailing list