[RFC PATCH v4 0/2] mtd: nand: vf610_nfc: make use of ->exec_op()

[Boris Brezillon]

On Thu, 22 Feb 2018 21:29:16 +0100
Stefan Agner <stefan at agner.ch> wrote:

> Fourth revision of the rework patchset to use exec_op for NXP
> Vybrid (and others) NAND Flash Controller. The most important
> change tries to implement a nicer way of handling the endianness
> hack.
> 
> However, this currently fails oobtest and nandbiterrs test. With
> some debugging enabled it looks like this:
> [   42.930460] mtd_oobtest: writing OOBs of whole device
> [   42.935576] vf610_nfc 400e0000.nand: OP_CMD: code 0xff
> [   42.944713] vf610_nfc 400e0000.nand: OP_CMD: code 0x70
> [   42.949955] vf610_nfc 400e0000.nand: OP_CMD: code 0x80
> [   42.955254] vf610_nfc 400e0000.nand: OP_ADDR: col 2048, row 1024
> [   42.961387] vf610_nfc 400e0000.nand: OP_DATA_OUT: len 64, offset 0
> [   42.974332] vf610_nfc 400e0000.nand: OP_CMD: code 0x70
> [   42.983101] vf610_nfc_write_oob, ret -5
> [   42.986986] mtd_oobtest: error: writeoob failed at 0x0
> [   42.992311] mtd_oobtest: error: use_len 2, use_offset 0
> [   42.999054] mtd_oobtest: error -5 occurred
> [   43.003301] =================================================
> 
> It seems that when I set page_access on such granular level I
> do in the current patchset version, then it influences commands
> such as status too... I guess I have to partially reimplement
> nand_exec_prog_page_op..?

Oh, right, that's probably the problem you have: when you read the
first byte of the SRAM what you actually read is the fourth one,
which has never been transmitted on the bus since the core only
requested one byte (the status byte). To solve that, you can call
nand_prog_page_begin_op() with ->page_access = true, then set
->page_access to false and call nand_prog_page_end_op().

> 
> --
> Stefan
> 
> Changes in v4:
> - Rebased to nand/next
> - Simplify filling of address cycles
> - Use accessors for SRAM (vf610_nfc_rd_from_sram/vf610_nfc_wr_to_sram)
> - Use two op-parser patterns to avoid a single command reading and writing
>   in a single operation
> - Implement (read|write)_(page|oob)[_raw] to set page_access
> - Set and clear vf610_nfc_ecc_mode in ecc (read|write)_page
> - Clear/set 16-bit config when 16-bit bus is used and 8-bit access is
>   requested
> 
> Changes in v3:
> - Separate exec_op() callback addition and removal of old callbacks
> - Push data into regs in one function
> - Readd op parser
> - Implement custom read/write page for hardware ECC
> - Rely on generic ecc.write_page_raw
> - Use nand_read_oob_op instead of nand_read_page_op
> 
> Stefan Agner (2):
>   mtd: nand: vf610_nfc: make use of ->exec_op()
>   mtd: nand: vf610_nfc: remove old hooks
> 
>  drivers/mtd/nand/raw/vf610_nfc.c | 642 ++++++++++++++++++++++++---------------
>  1 file changed, 399 insertions(+), 243 deletions(-)
> 



-- 
Boris Brezillon, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com