[PATCH 1/9] mtd: nand: qcom: use the ecc strength from device parameter

[Miquel Raynal]

Hi Abhishek,

On Thu, 12 Apr 2018 15:29:48 +0530, Abhishek Sahu
<absahu at codeaurora.org> wrote:

> On 2018-04-10 13:37, Boris Brezillon wrote:
> > On Tue, 10 Apr 2018 09:55:58 +0200
> > Miquel Raynal <miquel.raynal at bootlin.com> wrote:  
> > >> > Hi Abhishek,  
> >> >
> >> > On Tue, 10 Apr 2018 11:39:35 +0530, Abhishek Sahu
> >> > <absahu at codeaurora.org> wrote:
> >> >  
> >> > > On 2018-04-06 18:01, Miquel Raynal wrote:  
> >> > > > Hi Abhishek,
> >> > > >
> >> > > > On Wed,  4 Apr 2018 18:12:17 +0530, Abhishek Sahu
> >> > > > <absahu at codeaurora.org> wrote:
> >> > > >  
> >> > > >> Currently the driver uses the ECC strength specified in
> >> > > >> device tree. The ONFI or JEDEC device parameter page
> >> > > >> contains the ‘ECC correctability’ field which indicates the
> >> > > >> number of bits that the host should be able to correct per
> >> > > >> 512 bytes of data.  
> >> > > >
> >> > > > This is misleading. This field is not about the controller but rather
> >> > > > the chip requirements in terms of minimal strength for nominal use.
> >> > > >  
> >> > >
> >> > >   Thanks Miquel.
> >> > >
> >> > >   Yes. Its NAND chip requirement. I have used the description for
> >> > >   NAND ONFI param page
> >> > >
> >> > >   5.6.1.24. Byte 112: Number of bits ECC correctability
> >> > >   This field indicates the number of bits that the host should be
> >> > >   able to correct per 512 bytes of data.
> >> > >  
> >> > > >> The ecc correctability is assigned in
> >> > > >> chip parameter during device probe time. QPIC/EBI2 NAND
> >> > > >> supports 4/8-bit ecc correction. The Same kind of board
> >> > > >> can have different NAND parts so use the ecc strength
> >> > > >> from device parameter (if its non zero) instead of
> >> > > >> device tree.  
> >> > > >
> >> > > > That is not what you do.
> >> > > >
> >> > > > What you do is forcing the strength to be 8-bit per ECC chunk if the
> >> > > > NAND chip requires at least 8-bit/chunk strength.
> >> > > >
> >> > > > The DT property is here to force a strength. Otherwise, Linux will
> >> > > > propose to the NAND controller to use the minimum strength required by
> >> > > > the chip (from either the ONFI/JEDEC parameter page or from a static
> >> > > > table).
> >> > > >  
> >> > >
> >> > >   The main problem is that the same kind of boards can have different
> >> > >   NAND parts.
> >> > >
> >> > >   Lets assume, we have following 2 cases.
> >> > >
> >> > >   1. Non ONFI/JEDEC device for which chip->ecc_strength_ds
> >> > >      will be zero. In this case, the ecc->strength from DT
> >> > >      will be used  
> >> >
> >> > No, the strength from DT will always be used if the property is
> >> > present, no matter the type of chip.
> >> >  
> >> > >   2. ONFI/JEDEC device for which chip->ecc_strength_ds > 8.
> >> > >      Since QCOM nand controller can not support
> >> > >      ECC correction greater than 8 bits so we can use 8 bit ECC
> >> > >      itself instead of failing NAND boot completely.  
> >> >
> >> > I understand that. But this is still not what you do.
> >> >  
> >> > >  
> >> > > > IMHO, you have two solutions:
> >> > > > 1/ Remove these properties from the board DT (breaks DT backward
> >> > > > compatibility though);  
> >> > >
> >> > >   - nand-ecc-strength: This is optional property in nand.txt and
> >> > >     Required property in qcom_nandc.txt.  
> >> >
> >> > Well, this property is not controller specific but chip specific. The
> >> > controller driver does not rely on it, so this property should not be
> >> > required.
> >> >  
> >> > > We can't remove since
> >> > >     if the device is Non ONFI/JEDEC, then ecc strength will come
> >> > >     from DT only.  
> >> >
> >> > We can remove it and let the core handle this (as this is generic to
> >> > all raw NANDs and not specific to this controller driver). Try it out!  
> 
>   Thanks Boris and Miquel for your inputs.
> 
>   Just want to confirm if already its implemented in core layer
>   or shall I explore regrading this option.
> 
>   I checked by removing this property alone from dtsi and it was
>   failing with
> 
>   "Driver must set ecc.strength when using hardware ECC"
> 
>   I checked the code in nand_base.c also but couldn't get
>   anything related with this.

I don't know exactly what you did but you should have a look at what
lead you to this path:
https://elixir.bootlin.com/linux/v4.17-rc1/source/drivers/mtd/nand/raw/nand_base.c#L6421

Thanks,
Miquèl