[PATCH v10 12/16] MIPS: lantiq: Add a GPHY driver which uses the RCU syscon-mfd
Martin Blumenstingl
martin.blumenstingl at googlemail.com
Mon Sep 4 10:39:43 PDT 2017
On Sun, Aug 20, 2017 at 12:18 AM, Hauke Mehrtens <hauke at hauke-m.de> wrote:
> From: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
>
> Compared to the old xrx200_phy_fw driver the new version has multiple
> enhancements. The name of the firmware files does not have to be added
> to all .dts files anymore - one now configures the GPHY mode (FE or GE)
> instead. Each GPHY can now also boot separate firmware (thus mixing of
> GE and FE GPHYs is now possible).
> The new implementation is based on the RCU syscon-mfd and uses the
> reeset_controller framework instead of raw RCU register reads/writes.
>
> Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
> Reviewed-by: Andy Shevchenko <andy.shevchenko at gmail.com>
> Acked-by: Rob Herring <robh at kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> ---
> .../devicetree/bindings/mips/lantiq/rcu-gphy.txt | 36 +++
> arch/mips/lantiq/xway/sysctrl.c | 6 +-
> drivers/soc/lantiq/Makefile | 1 +
> drivers/soc/lantiq/gphy.c | 260 +++++++++++++++++++++
> include/dt-bindings/mips/lantiq_rcu_gphy.h | 15 ++
> 5 files changed, 316 insertions(+), 2 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt
> create mode 100644 drivers/soc/lantiq/gphy.c
> create mode 100644 include/dt-bindings/mips/lantiq_rcu_gphy.h
>
> diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt
> new file mode 100644
> index 000000000000..a0c19bd1ce66
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt
> @@ -0,0 +1,36 @@
> +Lantiq XWAY SoC GPHY binding
> +============================
> +
> +This binding describes a software-defined ethernet PHY, provided by the RCU
> +module on newer Lantiq XWAY SoCs (xRX200 and newer).
> +
> +-------------------------------------------------------------------------------
> +Required properties:
> +- compatible : Should be one of
> + "lantiq,xrx200a1x-gphy"
> + "lantiq,xrx200a2x-gphy"
> + "lantiq,xrx300-gphy"
> + "lantiq,xrx330-gphy"
> +- reg : Addrress of the GPHY FW load address register
> +- resets : Must reference the RCU GPHY reset bit
> +- reset-names : One entry, value must be "gphy" or optional "gphy2"
> +- clocks : A reference to the (PMU) GPHY clock gate
> +
> +Optional properties:
> +- lantiq,gphy-mode : GPHY_MODE_GE (default) or GPHY_MODE_FE as defined in
> + <dt-bindings/mips/lantiq_xway_gphy.h>
> +
> +
> +-------------------------------------------------------------------------------
> +Example for the GPHys on the xRX200 SoCs:
> +
> +#include <dt-bindings/mips/lantiq_rcu_gphy.h>
> + gphy0: gphy at 20 {
> + compatible = "lantiq,xrx200a2x-gphy";
> + reg = <0x20 0x4>;
> +
> + resets = <&reset0 31 30>, <&reset1 7 7>;
> + reset-names = "gphy", "gphy2";
> + clocks = <&pmu0 XRX200_PMU_GATE_GPHY>;
> + lantiq,gphy-mode = <GPHY_MODE_GE>;
> + };
> diff --git a/arch/mips/lantiq/xway/sysctrl.c b/arch/mips/lantiq/xway/sysctrl.c
> index 706639a343bc..87eab4d288e5 100644
> --- a/arch/mips/lantiq/xway/sysctrl.c
> +++ b/arch/mips/lantiq/xway/sysctrl.c
> @@ -518,7 +518,8 @@ void __init ltq_soc_init(void)
> clkdev_add_pmu("1e108000.eth", NULL, 0, 0, PMU_SWITCH |
> PMU_PPE_DP | PMU_PPE_TC);
> clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
> - clkdev_add_pmu("1f203000.rcu", "gphy", 1, 0, PMU_GPHY);
> + clkdev_add_pmu("1f203020.gphy", NULL, 1, 0, PMU_GPHY);
> + clkdev_add_pmu("1f203068.gphy", NULL, 1, 0, PMU_GPHY);
> clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
> clkdev_add_pmu("1e116000.mei", "afe", 1, 2, PMU_ANALOG_DSL_AFE);
> clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
> @@ -541,7 +542,8 @@ void __init ltq_soc_init(void)
> PMU_SWITCH | PMU_PPE_DPLUS | PMU_PPE_DPLUM |
> PMU_PPE_EMA | PMU_PPE_TC | PMU_PPE_SLL01 |
> PMU_PPE_QSB | PMU_PPE_TOP);
> - clkdev_add_pmu("1f203000.rcu", "gphy", 0, 0, PMU_GPHY);
> + clkdev_add_pmu("1f203020.gphy", NULL, 0, 0, PMU_GPHY);
> + clkdev_add_pmu("1f203068.gphy", NULL, 0, 0, PMU_GPHY);
> clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO);
> clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
> clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
> diff --git a/drivers/soc/lantiq/Makefile b/drivers/soc/lantiq/Makefile
> index 35aa86bd1023..be9e866d53e5 100644
> --- a/drivers/soc/lantiq/Makefile
> +++ b/drivers/soc/lantiq/Makefile
> @@ -1 +1,2 @@
> obj-y += fpi-bus.o
> +obj-$(CONFIG_XRX200_PHY_FW) += gphy.o
> diff --git a/drivers/soc/lantiq/gphy.c b/drivers/soc/lantiq/gphy.c
> new file mode 100644
> index 000000000000..8d8659463b3e
> --- /dev/null
> +++ b/drivers/soc/lantiq/gphy.c
> @@ -0,0 +1,260 @@
> +/*
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published
> + * by the Free Software Foundation.
> + *
> + * Copyright (C) 2012 John Crispin <blogic at phrozen.org>
> + * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> + * Copyright (C) 2017 Hauke Mehrtens <hauke at hauke-m.de>
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/firmware.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/reboot.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <linux/of_device.h>
> +#include <linux/of_platform.h>
> +#include <linux/property.h>
> +#include <dt-bindings/mips/lantiq_rcu_gphy.h>
> +
> +#include <lantiq_soc.h>
> +
> +#define XRX200_GPHY_FW_ALIGN (16 * 1024)
> +
> +struct xway_gphy_priv {
> + struct clk *gphy_clk_gate;
> + struct reset_control *gphy_reset;
> + struct reset_control *gphy_reset2;
> + struct notifier_block gphy_reboot_nb;
> + void __iomem *membase;
> + char *fw_name;
> +};
> +
> +struct xway_gphy_match_data {
> + char *fe_firmware_name;
> + char *ge_firmware_name;
> +};
> +
> +static const struct xway_gphy_match_data xrx200a1x_gphy_data = {
> + .fe_firmware_name = "lantiq/xrx200_phy22f_a14.bin",
> + .ge_firmware_name = "lantiq/xrx200_phy11g_a14.bin",
> +};
> +
> +static const struct xway_gphy_match_data xrx200a2x_gphy_data = {
> + .fe_firmware_name = "lantiq/xrx200_phy22f_a22.bin",
> + .ge_firmware_name = "lantiq/xrx200_phy11g_a22.bin",
> +};
> +
> +static const struct xway_gphy_match_data xrx300_gphy_data = {
> + .fe_firmware_name = "lantiq/xrx300_phy22f_a21.bin",
> + .ge_firmware_name = "lantiq/xrx300_phy11g_a21.bin",
> +};
> +
> +static const struct of_device_id xway_gphy_match[] = {
> + { .compatible = "lantiq,xrx200a1x-gphy", .data = &xrx200a1x_gphy_data },
> + { .compatible = "lantiq,xrx200a2x-gphy", .data = &xrx200a2x_gphy_data },
> + { .compatible = "lantiq,xrx300-gphy", .data = &xrx300_gphy_data },
> + { .compatible = "lantiq,xrx330-gphy", .data = &xrx300_gphy_data },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, xway_gphy_match);
> +
> +static struct xway_gphy_priv *to_xway_gphy_priv(struct notifier_block *nb)
> +{
> + return container_of(nb, struct xway_gphy_priv, gphy_reboot_nb);
> +}
> +
> +static int xway_gphy_reboot_notify(struct notifier_block *reboot_nb,
> + unsigned long code, void *unused)
> +{
> + struct xway_gphy_priv *priv = to_xway_gphy_priv(reboot_nb);
> +
> + if (priv) {
> + reset_control_assert(priv->gphy_reset);
> + reset_control_assert(priv->gphy_reset2);
> + }
> +
> + return NOTIFY_DONE;
> +}
> +
> +static int xway_gphy_load(struct device *dev, struct xway_gphy_priv *priv,
> + dma_addr_t *dev_addr)
> +{
> + const struct firmware *fw;
> + void *fw_addr;
> + dma_addr_t dma_addr;
> + size_t size;
> + int ret;
> +
> + ret = request_firmware(&fw, priv->fw_name, dev);
> + if (ret) {
> + dev_err(dev, "failed to load firmware: %s, error: %i\n",
> + priv->fw_name, ret);
> + return ret;
> + }
> +
> + /*
> + * GPHY cores need the firmware code in a persistent and contiguous
> + * memory area with a 16 kB boundary aligned start address.
> + */
> + size = fw->size + XRX200_GPHY_FW_ALIGN;
> +
> + fw_addr = dmam_alloc_coherent(dev, size, &dma_addr, GFP_KERNEL);
> + if (fw_addr) {
> + fw_addr = PTR_ALIGN(fw_addr, XRX200_GPHY_FW_ALIGN);
> + *dev_addr = ALIGN(dma_addr, XRX200_GPHY_FW_ALIGN);
> + memcpy(fw_addr, fw->data, fw->size);
> + } else {
> + dev_err(dev, "failed to alloc firmware memory\n");
> + ret = -ENOMEM;
> + }
> +
> + release_firmware(fw);
> +
> + return ret;
> +}
> +
> +static int xway_gphy_of_probe(struct platform_device *pdev,
> + struct xway_gphy_priv *priv)
> +{
> + struct device *dev = &pdev->dev;
> + const struct xway_gphy_match_data *gphy_fw_name_cfg;
> + u32 gphy_mode;
> + int ret;
> + struct resource *res_gphy;
> +
> + gphy_fw_name_cfg = of_device_get_match_data(dev);
> +
> + priv->gphy_clk_gate = devm_clk_get(dev, NULL);
> + if (IS_ERR(priv->gphy_clk_gate)) {
> + dev_err(dev, "Failed to lookup gate clock\n");
> + return PTR_ERR(priv->gphy_clk_gate);
> + }
> +
> + res_gphy = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + priv->membase = devm_ioremap_resource(dev, res_gphy);
> + if (IS_ERR(priv->membase))
> + return PTR_ERR(priv->membase);
> +
> + priv->gphy_reset = devm_reset_control_get(dev, "gphy");
> + if (IS_ERR(priv->gphy_reset)) {
> + if (PTR_ERR(priv->gphy_reset) != -EPROBE_DEFER)
> + dev_err(dev, "Failed to lookup gphy reset\n");
> + return PTR_ERR(priv->gphy_reset);
> + }
> +
> + priv->gphy_reset2 = devm_reset_control_get_optional(dev, "gphy2");
> + if (IS_ERR(priv->gphy_reset2))
> + return PTR_ERR(priv->gphy_reset2);
> +
> + ret = device_property_read_u32(dev, "lantiq,gphy-mode", &gphy_mode);
> + /* Default to GE mode */
> + if (ret)
> + gphy_mode = GPHY_MODE_GE;
> +
> + switch (gphy_mode) {
> + case GPHY_MODE_FE:
> + priv->fw_name = gphy_fw_name_cfg->fe_firmware_name;
> + break;
> + case GPHY_MODE_GE:
> + priv->fw_name = gphy_fw_name_cfg->ge_firmware_name;
> + break;
> + default:
> + dev_err(dev, "Unknown GPHY mode %d\n", gphy_mode);
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int xway_gphy_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct xway_gphy_priv *priv;
> + dma_addr_t fw_addr = 0;
> + int ret;
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + ret = xway_gphy_of_probe(pdev, priv);
> + if (ret)
> + return ret;
> +
> + ret = clk_prepare_enable(priv->gphy_clk_gate);
> + if (ret)
> + return ret;
> +
> + ret = xway_gphy_load(dev, priv, &fw_addr);
> + if (ret) {
> + clk_disable_unprepare(priv->gphy_clk_gate);
> + return ret;
> + }
> +
> + reset_control_assert(priv->gphy_reset);
> + reset_control_assert(priv->gphy_reset2);
> +
> + iowrite32be(fw_addr, priv->membase);
> +
> + reset_control_deassert(priv->gphy_reset);
> + reset_control_deassert(priv->gphy_reset2);
> +
> + /* assert the gphy reset because it can hang after a reboot: */
> + priv->gphy_reboot_nb.notifier_call = xway_gphy_reboot_notify;
> + priv->gphy_reboot_nb.priority = -1;
> +
> + ret = register_reboot_notifier(&priv->gphy_reboot_nb);
> + if (ret)
> + dev_warn(dev, "Failed to register reboot notifier\n");
> +
> + platform_set_drvdata(pdev, priv);
> +
> + return ret;
> +}
> +
> +static int xway_gphy_remove(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct xway_gphy_priv *priv = platform_get_drvdata(pdev);
> + int ret;
> +
> + reset_control_assert(priv->gphy_reset);
> + reset_control_assert(priv->gphy_reset2);
> +
> + iowrite32be(0, priv->membase);
> +
> + clk_disable_unprepare(priv->gphy_clk_gate);
> +
> + ret = unregister_reboot_notifier(&priv->gphy_reboot_nb);
> + if (ret)
> + dev_warn(dev, "Failed to unregister reboot notifier\n");
> +
> + return 0;
> +}
> +
> +static struct platform_driver xway_gphy_driver = {
> + .probe = xway_gphy_probe,
> + .remove = xway_gphy_remove,
> + .driver = {
> + .name = "xway-rcu-gphy",
> + .of_match_table = xway_gphy_match,
> + },
> +};
> +
> +module_platform_driver(xway_gphy_driver);
> +
> +MODULE_FIRMWARE("lantiq/xrx300_phy11g_a21.bin");
> +MODULE_FIRMWARE("lantiq/xrx300_phy22f_a21.bin");
> +MODULE_FIRMWARE("lantiq/xrx200_phy11g_a14.bin");
> +MODULE_FIRMWARE("lantiq/xrx200_phy11g_a22.bin");
> +MODULE_FIRMWARE("lantiq/xrx200_phy22f_a14.bin");
> +MODULE_FIRMWARE("lantiq/xrx200_phy22f_a22.bin");
> +MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl at googlemail.com>");
> +MODULE_DESCRIPTION("Lantiq XWAY GPHY Firmware Loader");
> +MODULE_LICENSE("GPL");
> diff --git a/include/dt-bindings/mips/lantiq_rcu_gphy.h b/include/dt-bindings/mips/lantiq_rcu_gphy.h
> new file mode 100644
> index 000000000000..fa1a63773342
> --- /dev/null
> +++ b/include/dt-bindings/mips/lantiq_rcu_gphy.h
> @@ -0,0 +1,15 @@
> +/*
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published
> + * by the Free Software Foundation.
> + *
> + * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> + * Copyright (C) 2017 Hauke Mehrtens <hauke at hauke-m.de>
> + */
> +#ifndef _DT_BINDINGS_MIPS_LANTIQ_RCU_GPHY_H
> +#define _DT_BINDINGS_MIPS_LANTIQ_RCU_GPHY_H
> +
> +#define GPHY_MODE_GE 1
> +#define GPHY_MODE_FE 2
> +
> +#endif /* _DT_BINDINGS_MIPS_LANTIQ_RCU_GPHY_H */
> --
> 2.11.0
>
More information about the linux-mtd
mailing list