[PATCH v2 0/5] mtd: nand: add support for on-die ECC

[Boris Brezillon]

On Sat, 29 Apr 2017 11:06:41 +0200
Thomas Petazzoni <thomas.petazzoni at free-electrons.com> wrote:

> Hello,
> 
> This patch series adds support for on-die ECC, i.e ECC performed by
> the NAND chip itself, as opposed to having the ECC calculated by the
> NAND controller or in software.
> 
> It is useful in situations where the NAND chip has an ECC requirement
> that is not met by the ECC capabilities of the NAND controller.
> 
> Patch 1 adjusts the NAND generic DT binding to add "on-die" as an
> nand-ecc-mode.
> 
> Patch 2 adds the core support for on-die ECC, which is really simple
> and minimal: all the work is really done in the vendor-specific NAND
> code.
> 
> Patch 3 and 4 adds the on-die ECC implementation for Micron NANDs.
> 
> Patch 5 allows the FSMC NAND driver to use on-die ECC.
> 
> This series was tested on a SPEAr600 platform, with a Micron
> MT29F1G08ABADAWP NAND. The mtd_nandbiterrs.ko test is passing
> successfully, which shows that the on-die ECC is correcting bitflips
> as expected.
> 
> This series is based on the current nand-next branch, as it depends on
> the rework from Boris of the vendor-specific NAND code.
> 
> Many thanks to Boris from providing lots of useful feedback and
> discussion during the development of this patch series.

Applied to nand/next.

Thanks,

Boris

> 
> Changes since v1:
> 
>  - Rebased on the latest nand/next branch.
> 
>  - Reworked the mechanism to detect if the Micron NAND suppors on-die
>    ECC. We realized that the READ_ID command only indicates if on-die
>    ECC is currently enabled or not, not whether it is supported by the
>    NAND. After discussion with Bean Huo from Micron we came up with a
>    logic to determine if the NAND has on-die ECC support, which PATCH
>    4/5 implements.
> 
>    Note that we intentionally only support cases that we could
>    test. Therefore, we error out if the NAND has an on-die ECC that
>    cannot be disabled, and we error out if the NAND uses a 8 bits per
>    512 bytes on-die ECC, since it requires a slightly different
>    handling than the 4 bits per 512 bytes on-die ECC our NAND is
>    using.
> 
>  - Added Acked-by from Rob Herring on PATCH 1/5 (DT binding)
> 
>  - Added Acked-by from Richard Weinberger on all patches, except PATCH
>    4/5 since it was significantly changed.
> 
> Best regards,
> 
> Thomas
> 
> 
> Thomas Petazzoni (5):
>   dt-bindings: mtd: document new "on-die" nand-ecc-mode
>   mtd: nand: add core support for on-die ECC
>   mtd: nand: export nand_{read,write}_page_raw()
>   mtd: nand: add support for Micron on-die ECC
>   mtd: nand: fsmc_nand: handle on-die ECC case
> 
>  Documentation/devicetree/bindings/mtd/nand.txt |   2 +-
>  drivers/mtd/nand/fsmc_nand.c                   |   3 +
>  drivers/mtd/nand/nand_base.c                   |  23 ++-
>  drivers/mtd/nand/nand_micron.c                 | 215 +++++++++++++++++++++++++
>  include/linux/mtd/nand.h                       |  11 ++
>  5 files changed, 249 insertions(+), 5 deletions(-)
>