[RESEND PATCH v2 00/53] mtd: nand: denali: 2nd round of Denali NAND IP patch bomb

[Masahiro Yamada]

Hi Boris,



2017-03-25 5:13 GMT+09:00 Boris Brezillon <boris.brezillon at free-electrons.com>:

>>
>> Masahiro Yamada (53):
>>   mtd: nand: allow to set only one of ECC size and ECC strength from DT
>>   mtd: nand: use read_oob() instead of cmdfunc() for bad block check
>>   mtd: nand: denali: remove unused CONFIG option and macros
>>   mtd: nand: denali: remove redundant define of BANK(x)
>>   mtd: nand: denali: remove more unused struct members
>>   mtd: nand: denali: fix comment of denali_nand_info::flash_mem
>>   mtd: nand: denali: consolidate INTR_STATUS__* and INTR_EN__* macros
>>   mtd: nand: denali: introduce capability flag
>>   mtd: nand: denali: use int where no reason to use fixed width variable
>>   mtd: nand: denali: fix erased page checking
>>   mtd: nand: denali: fix bitflips calculation in handle_ecc()
>>   mtd: nand: denali: support HW_ECC_FIXUP capability
>>   mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
>>   mtd: nand: denali: support 64bit capable DMA engine
>>   mtd: nand: denali_dt: remove dma-mask DT property
>>   mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
>>   mtd: nand: denali: allow to override revision number
>>   mtd: nand: denali: use nand_chip to hold frequently accessed data
>>   mtd: nand: denali: call nand_set_flash_node() to set DT node
>>   mtd: nand: denali: do not set mtd->name
>>   mtd: nand: denali: move multi device fixup code to a helper function
>>   mtd: nand: denali: simplify multi device fixup code
>>   mtd: nand: denali: set DEVICES_CONNECTED 1 if not set
>>   mtd: nand: denali: remove meaningless writes to read-only registers
>>   mtd: nand: denali: remove unnecessary writes to ECC_CORRECTION
>>   mtd: nand: denali: support 1024 byte ECC step size
>>   mtd: nand: denali: avoid hard-coding ecc.strength and ecc.bytes
>>   mtd: nand: denali: support "nand-ecc-strength" DT property
>>   mtd: nand: denali: remove Toshiba and Hynix specific fixup code
>>   mtd: nand: denali_dt: add compatible strings for UniPhier SoC variants
>>   mtd: nand: denali: set NAND_ECC_CUSTOM_PAGE_ACCESS
>>   mtd: nand: denali: do not propagate NAND_STATUS_FAIL to waitfunc()
>>   mtd: nand: denali: use BIT() and GENMASK() for register macros
>>   mtd: nand: denali: remove unneeded find_valid_banks()
>>   mtd: nand: denali: handle timing parameters by setup_data_interface()
>>   mtd: nand: denali: remove meaningless pipeline read-ahead operation
>>   mtd: nand: denali: rework interrupt handling
>>   mtd: nand: denali: fix NAND_CMD_STATUS handling
>>   mtd: nand: denali: fix NAND_CMD_PARAM handling
>>   mtd: nand: do not check R/B# for CMD_READID in nand_command(_lp)
>>   mtd: nand: do not check R/B# for CMD_SET_FEATURES in nand_command(_lp)
>>   mtd: nand: denali: switch over to cmd_ctrl instead of cmdfunc
>>   mtd: nand: denali: fix bank reset function
>>   mtd: nand: denali: use interrupt instead of polling for bank reset
>>   mtd: nand: denali: propagate page to helpers via function argument
>>   mtd: nand: denali: merge struct nand_buf into struct denali_nand_info
>>   mtd: nand: denali: use flag instead of register macro for direction
>>   mtd: nand: denali: fix raw and oob accessors for syndrome page layout
>>   mtd: nand: denali: support hardware-assisted erased page detection
>>   mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
>>   mtd: nand: denali: skip driver internal bounce buffer when possible
>>   mtd: nand: denali: use non-managed kmalloc() for DMA buffer
>>   mtd: nand: denali: enable bad block table scan
>
> Applied patch 1 to 9, 40 and 41. I'll see what else I can apply so that
> you don't have to re-post the remaining 42 patches, but I fear some of
> them won't apply correctly without patch 10 on which I had comments.

Thanks!

This will be very helpful when sending the next version.

If you like, you can also apply the following 9 patches cleanly in this order.

18/53 mtd: nand: denali: use nand_chip to hold frequently accessed data
19/53 mtd: nand: denali: call nand_set_flash_node() to set DT node
20/53 mtd: nand: denali: do not set mtd->name
21/53 mtd: nand: denali: move multi device fixup code to a helper function
22/53 mtd: nand: denali: simplify multi device fixup code
23/53 mtd: nand: denali: set DEVICES_CONNECTED 1 if not set
24/53 mtd: nand: denali: remove meaningless writes to read-only registers
25/53 mtd: nand: denali: remove unnecessary writes to ECC_CORRECTION
36/53 mtd: nand: denali: remove meaningless pipeline read-ahead operation

These are less controversial, and have no dependency on 10/53-17/53.




50/53 "mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset"
is a change to the NAND framework.  (used as a pre-requisite for 51/53)

Surely no dependency on the others, but If you wait more for comments
from other developers, that's no problem.



I will update the commented parts,
and hopefully send v3 next week.

Thanks!


-- 
Best Regards
Masahiro Yamada