[PATCH V3] mtd: bcm47xxsflash: support reading flash out of mapping window

[Marek Vasut]

On 01/23/2017 12:51 PM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal at milecki.pl>
> 
> For reading flash content we use MMIO but it's possible to read only
> first 16 MiB this way. It's simply an arch design/limitation.
> To support flash sizes bigger than 16 MiB implement indirect access
> using ChipCommon registers.
> This has been tested using MX25L25635F.
> 
> Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
> ---
> V2: Simplify line writing to buf
>     Add some trivial comment for OPCODE_ST_READ4B
>     Both requested by Marek
> V3: Use as much as possible MMIO access for read crossing boundary (performance)

It's not because of performance, but because you can start reading at 15
MiB offset and read 2 MiB , at which point the previous patch would IMO
fail.

Acked-by: Marek Vasut <marek.vasut at gmail.com>

Thanks!

> ---
>  drivers/mtd/devices/bcm47xxsflash.c | 23 ++++++++++++++++++++---
>  drivers/mtd/devices/bcm47xxsflash.h |  3 +++
>  2 files changed, 23 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/mtd/devices/bcm47xxsflash.c b/drivers/mtd/devices/bcm47xxsflash.c
> index 4decd8c0360a..138689619ab4 100644
> --- a/drivers/mtd/devices/bcm47xxsflash.c
> +++ b/drivers/mtd/devices/bcm47xxsflash.c
> @@ -105,15 +105,32 @@ static int bcm47xxsflash_read(struct mtd_info *mtd, loff_t from, size_t len,
>  			      size_t *retlen, u_char *buf)
>  {
>  	struct bcm47xxsflash *b47s = mtd->priv;
> +	size_t orig_len = len;
>  
>  	/* Check address range */
>  	if ((from + len) > mtd->size)
>  		return -EINVAL;
>  
> -	memcpy_fromio(buf, b47s->window + from, len);
> -	*retlen = len;
> +	/* Read as much as possible using fast MMIO window */
> +	if (from < BCM47XXSFLASH_WINDOW_SZ) {
> +		size_t memcpy_len;
>  
> -	return len;
> +		memcpy_len = min(len, (size_t)(BCM47XXSFLASH_WINDOW_SZ - from));
> +		memcpy_fromio(buf, b47s->window + from, memcpy_len);
> +		from += memcpy_len;
> +		len -= memcpy_len;
> +	}
> +
> +	/* Use indirect access for content out of the window */
> +	for (; len; len--) {
> +		b47s->cc_write(b47s, BCMA_CC_FLASHADDR, from++);
> +		bcm47xxsflash_cmd(b47s, OPCODE_ST_READ4B);
> +		*buf++ = b47s->cc_read(b47s, BCMA_CC_FLASHDATA);
> +	}
> +
> +	*retlen = orig_len;
> +
> +	return orig_len;
>  }
>  
>  static int bcm47xxsflash_write_st(struct mtd_info *mtd, u32 offset, size_t len,
> diff --git a/drivers/mtd/devices/bcm47xxsflash.h b/drivers/mtd/devices/bcm47xxsflash.h
> index 1564b62b412e..b2d7b38f75fd 100644
> --- a/drivers/mtd/devices/bcm47xxsflash.h
> +++ b/drivers/mtd/devices/bcm47xxsflash.h
> @@ -3,6 +3,8 @@
>  
>  #include <linux/mtd/mtd.h>
>  
> +#define BCM47XXSFLASH_WINDOW_SZ			SZ_16M
> +
>  /* Used for ST flashes only. */
>  #define OPCODE_ST_WREN		0x0006		/* Write Enable */
>  #define OPCODE_ST_WRDIS		0x0004		/* Write Disable */
> @@ -16,6 +18,7 @@
>  #define OPCODE_ST_RES		0x03ab		/* Read Electronic Signature */
>  #define OPCODE_ST_CSA		0x1000		/* Keep chip select asserted */
>  #define OPCODE_ST_SSE		0x0220		/* Sub-sector Erase */
> +#define OPCODE_ST_READ4B	0x6313		/* Read Data Bytes in 4Byte addressing mode */
>  
>  /* Used for Atmel flashes only. */
>  #define OPCODE_AT_READ				0x07e8
> 


-- 
Best regards,
Marek Vasut