[PATCH -next v3 1/2] mtd: nand: toshiba: Retrieve ECC requirements from extended ID

[Boris Brezillon]

On Tue, 19 Dec 2017 20:42:36 +0900
KOBAYASHI Yoshitake <yoshitake.kobayashi at toshiba.co.jp> wrote:

> On 2017/12/07 0:08, Boris Brezillon wrote:
> > On Wed,  6 Dec 2017 23:04:57 +0900
> > KOBAYASHI Yoshitake <yoshitake.kobayashi at toshiba.co.jp> wrote:
> >   
> >> This patch enables support to read the ECC strength and size from the
> >> NAND flash using Toshiba Memory SLC NAND extended-ID. This patch is
> >> based on the information of the 6th ID byte of the Toshiba Memory SLC
> >> NAND.
> >>
> >> Signed-off-by: KOBAYASHI Yoshitake <yoshitake.kobayashi at toshiba.co.jp>
> >> ---
> >>  drivers/mtd/nand/nand_toshiba.c | 28 ++++++++++++++++++++++++++++
> >>  1 file changed, 28 insertions(+)
> >>
> >> diff --git a/drivers/mtd/nand/nand_toshiba.c b/drivers/mtd/nand/nand_toshiba.c
> >> index 57df857..c2c141b 100644
> >> --- a/drivers/mtd/nand/nand_toshiba.c
> >> +++ b/drivers/mtd/nand/nand_toshiba.c
> >> @@ -35,6 +35,34 @@ static void toshiba_nand_decode_id(struct nand_chip *chip)
> >>  	    (chip->id.data[5] & 0x7) == 0x6 /* 24nm */ &&
> >>  	    !(chip->id.data[4] & 0x80) /* !BENAND */)
> >>  		mtd->oobsize = 32 * mtd->writesize >> 9;
> >> +
> >> +	/*
> >> +	 * Extract ECC requirements from 6th id byte.
> >> +	 * For Toshiba SLC, ecc requrements are as follows:
> >> +	 *  - 43nm: 1 bit ECC for each 512Byte is required.
> >> +	 *  - 32nm: 4 bit ECC for each 512Byte is required.
> >> +	 *  - 24nm: 8 bit ECC for each 512Byte is required.
> >> +	 */
> >> +	if (chip->id.len >= 6 && nand_is_slc(chip)) {
> >> +		chip->ecc_step_ds = 512;
> >> +		switch (chip->id.data[5] & 0x7) {
> >> +		case 0x4:
> >> +			chip->ecc_strength_ds = 1;
> >> +			break;
> >> +		case 0x5:
> >> +			chip->ecc_strength_ds = 4;
> >> +			break;
> >> +		case 0x6:
> >> +			chip->ecc_strength_ds = 8;
> >> +			break;
> >> +		default:
> >> +			WARN(1, "Could not get ECC info");
> >> +			chip->ecc_step_ds = 0;
> >> +			break;
> >> +		}
> >> +	} else if (chip->id.len < 6 && nand_is_slc(chip)) {
> >> +		WARN(1, "Could not get ECC info, 6th nand id byte does not exist.");  
> > 
> > I'm pretty sure you have old NAND chips that do not have 6bytes ids
> > (see the table here [1]), and printing a huge backtrace in this case is
> > probably not what you want.
> > 
> > If you're okay with dropping this else block, I'll do the change when
> > applying, no need to send a new version.  
> 
> Some controllers may have limitation in reading ids beyond 5 bytes, 
> considering such scenario we think it is better to keep this warning.
> However if you feel huge backtrace is an issue, how about we using pr_warn() instead?
> 

Toshiba NANDs with an id smaller than 6 bytes exist, so no, we should
not complain at all. If the controller is broken and can't read the 8 id
bytes the core is asking for, then it should be detected at the core
level not in the NAND manufacturer driver.