[PATCH v4 09/20] mtd: nand: qcom: support for read location registers

Abhishek Sahu absahu at codeaurora.org
Wed Aug 16 00:34:51 PDT 2017 

On 2017-08-16 10:04, Archit Taneja wrote:
> On 08/11/2017 05:09 PM, Abhishek Sahu wrote:
>> In EBI2, all codeword data will be read in FLASH_BUF_ACC buffer
>> and ADM will copy the data from source (FLASH_BUF_ACC) to
>> destination (memory for data read).
>> 
>> In QPIC, there is no FLASH_BUF_ACC and all the codeword data will
>> held in QPIC BAM FIFO buffers. It provides multiple READ_LOCATION
>> registers which will be used for copying the data from FIFO to
>> memory. The READ_LOCATION register will be used to read a
>> specific amount of data from a specific offset within the flash
>> buffer. It supports sequential offset requests. Each request is
>> composed of the following fields:
>> 
>> a. Offset within the flash buffer from which data should be
>>     read
>> b. Amount of data to be read
>> c. Flag bit specifying the last read request from the flash
>>     buffer. Following the last read request the NANDc refers to the
>>     buffer as empty.
>> 
>> Signed-off-by: Abhishek Sahu <absahu at codeaurora.org>
>> ---
>>   drivers/mtd/nand/qcom_nandc.c | 64 
>> +++++++++++++++++++++++++++++++++++++++++++
>>   1 file changed, 64 insertions(+)
>> 
>> diff --git a/drivers/mtd/nand/qcom_nandc.c 
>> b/drivers/mtd/nand/qcom_nandc.c
>> index d9c8a6b..b452cfb 100644
>> --- a/drivers/mtd/nand/qcom_nandc.c
>> +++ b/drivers/mtd/nand/qcom_nandc.c
>> @@ -53,6 +53,8 @@
>>   #define	NAND_VERSION			0xf08
>>   #define	NAND_READ_LOCATION_0		0xf20
>>   #define	NAND_READ_LOCATION_1		0xf24
>> +#define	NAND_READ_LOCATION_2		0xf28
>> +#define	NAND_READ_LOCATION_3		0xf2c
>>     /* dummy register offsets, used by write_reg_dma */
>>   #define	NAND_DEV_CMD1_RESTORE		0xdead
>> @@ -135,6 +137,11 @@
>>   #define	ERASED_PAGE			(PAGE_ALL_ERASED | PAGE_ERASED)
>>   #define	ERASED_CW			(CODEWORD_ALL_ERASED | CODEWORD_ERASED)
>>   +/* NAND_READ_LOCATION_n bits */
>> +#define READ_LOCATION_OFFSET		0
>> +#define READ_LOCATION_SIZE		16
>> +#define READ_LOCATION_LAST		31
>> +
>>   /* Version Mask */
>>   #define	NAND_VERSION_MAJOR_MASK		0xf0000000
>>   #define	NAND_VERSION_MAJOR_SHIFT	28
>> @@ -177,6 +184,12 @@
>>   #define	ECC_BCH_4BIT	BIT(2)
>>   #define	ECC_BCH_8BIT	BIT(3)
>>   +#define nandc_set_readl(nandc, reg, offset, size, is_last)	\
> 
> Minor nit, readl makes one think it's 'read long'. If it isn't too
> much effort, could you s/nandc_set_readl/nandc_set_read_loc ?
> 

  Thanks Archit.
  Yes that would be better. I will change the name.

>> +nandc_set_reg(nandc, NAND_READ_LOCATION_##reg,			\
>> +	      ((offset) << READ_LOCATION_OFFSET) |		\
>> +	      ((size) << READ_LOCATION_SIZE) |			\
>> +	      ((is_last) << READ_LOCATION_LAST))
>> +
>>   #define QPIC_PER_CW_CMD_SGL		32
>>   #define QPIC_PER_CW_DATA_SGL		8
>>   @@ -260,6 +273,11 @@ struct nandc_regs {
>>   	__le32 orig_vld;
>>     	__le32 ecc_buf_cfg;
>> +	__le32 read_location0;
>> +	__le32 read_location1;
>> +	__le32 read_location2;
>> +	__le32 read_location3;
>> +
>>   };
>>     /*
>> @@ -516,6 +534,14 @@ static __le32 *offset_to_nandc_reg(struct 
>> nandc_regs *regs, int offset)
>>   		return &regs->orig_vld;
>>   	case NAND_EBI2_ECC_BUF_CFG:
>>   		return &regs->ecc_buf_cfg;
>> +	case NAND_READ_LOCATION_0:
>> +		return &regs->read_location0;
>> +	case NAND_READ_LOCATION_1:
>> +		return &regs->read_location1;
>> +	case NAND_READ_LOCATION_2:
>> +		return &regs->read_location2;
>> +	case NAND_READ_LOCATION_3:
>> +		return &regs->read_location3;
>>   	default:
>>   		return NULL;
>>   	}
>> @@ -590,6 +616,10 @@ static void update_rw_regs(struct qcom_nand_host 
>> *host, int num_cw, bool read)
>>   	nandc_set_reg(nandc, NAND_FLASH_STATUS, host->clrflashstatus);
>>   	nandc_set_reg(nandc, NAND_READ_STATUS, host->clrreadstatus);
>>   	nandc_set_reg(nandc, NAND_EXEC_CMD, 1);
>> +
>> +	if (read)
>> +		nandc_set_readl(nandc, 0, 0, host->use_ecc ?
>> +				host->cw_data : host->cw_size, 1);
>>   }
>>     /*
>> @@ -835,6 +865,10 @@ static void config_nand_page_read(struct 
>> qcom_nand_controller *nandc)
>>    */
>>   static void config_nand_cw_read(struct qcom_nand_controller *nandc)
>>   {
>> +	if (nandc->props->is_bam)
>> +		write_reg_dma(nandc, NAND_READ_LOCATION_0, 4,
>> +			      NAND_BAM_NEXT_SGL);
>> +
>>   	write_reg_dma(nandc, NAND_FLASH_CMD, 1, NAND_BAM_NEXT_SGL);
>>   	write_reg_dma(nandc, NAND_EXEC_CMD, 1, NAND_BAM_NEXT_SGL);
>>   @@ -923,6 +957,7 @@ static int nandc_param(struct qcom_nand_host 
>> *host)
>>     	nandc_set_reg(nandc, NAND_DEV_CMD1_RESTORE, nandc->cmd1);
>>   	nandc_set_reg(nandc, NAND_DEV_CMD_VLD_RESTORE, nandc->vld);
>> +	nandc_set_readl(nandc, 0, 0, 512, 1);
>>     	write_reg_dma(nandc, NAND_DEV_CMD_VLD, 1, 0);
>>   	write_reg_dma(nandc, NAND_DEV_CMD1, 1, NAND_BAM_NEXT_SGL);
>> @@ -1398,6 +1433,19 @@ static int read_page_ecc(struct qcom_nand_host 
>> *host, u8 *data_buf,
>>   			oob_size = host->ecc_bytes_hw + host->spare_bytes;
>>   		}
>>   +		if (nandc->props->is_bam) {
>> +			if (data_buf && oob_buf) {
>> +				nandc_set_readl(nandc, 0, 0, data_size, 0);
>> +				nandc_set_readl(nandc, 1, data_size,
>> +						oob_size, 1);
>> +			} else if (data_buf) {
>> +				nandc_set_readl(nandc, 0, 0, data_size, 1);
>> +			} else {
>> +				nandc_set_readl(nandc, 0, data_size,
>> +						oob_size, 1);
>> +			}
>> +		}
>> +
>>   		config_nand_cw_read(nandc);
>>     		if (data_buf)
>> @@ -1457,6 +1505,7 @@ static int copy_last_cw(struct qcom_nand_host 
>> *host, int page)
>>     	set_address(host, host->cw_size * (ecc->steps - 1), page);
>>   	update_rw_regs(host, 1, true);
>> +	nandc_set_readl(nandc, 0, 0, size, 1);
> 
> The READ_LOC reg should already be set up in update_rw_regs, right? If
> so, we could
> drop this line.

  Yes. this line is redundant. I will remove the same.

> 
> With that,
> 
> Reviewed-by: Archit Taneja <architt at codeaurora.org>
> 
> Thanks,
> Archit
> 
>>     	config_nand_single_cw_page_read(nandc);
>>   @@ -1502,6 +1551,7 @@ static int qcom_nandc_read_page_raw(struct 
>> mtd_info *mtd,
>>   	u8 *data_buf, *oob_buf;
>>   	struct nand_ecc_ctrl *ecc = &chip->ecc;
>>   	int i, ret;
>> +	int read_loc;
>>     	data_buf = buf;
>>   	oob_buf = chip->oob_poi;
>> @@ -1527,6 +1577,20 @@ static int qcom_nandc_read_page_raw(struct 
>> mtd_info *mtd,
>>   			oob_size2 = host->ecc_bytes_hw + host->spare_bytes;
>>   		}
>>   +		if (nandc->props->is_bam) {
>> +			read_loc = 0;
>> +			nandc_set_readl(nandc, 0, read_loc, data_size1, 0);
>> +			read_loc += data_size1;
>> +
>> +			nandc_set_readl(nandc, 1, read_loc, oob_size1, 0);
>> +			read_loc += oob_size1;
>> +
>> +			nandc_set_readl(nandc, 2, read_loc, data_size2, 0);
>> +			read_loc += data_size2;
>> +
>> +			nandc_set_readl(nandc, 3, read_loc, oob_size2, 1);
>> +		}
>> +
>>   		config_nand_cw_read(nandc);
>>     		read_data_dma(nandc, reg_off, data_buf, data_size1, 0);
>>

More information about the linux-mtd mailing list