[PATCH v2 2/7] mtd: nand: move raw NAND related code to the raw/ subdir
Boris Brezillon
boris.brezillon at free-electrons.com
Sun Oct 16 07:35:13 PDT 2016
As part of the process of sharing more code between different NAND
based devices, we need to move all raw NAND related code to the raw/
subdirectory.
Signed-off-by: Boris Brezillon <boris.brezillon at free-electrons.com>
---
drivers/mtd/nand/Kconfig | 573 +--------------------
drivers/mtd/nand/Makefile | 63 +--
drivers/mtd/nand/raw/Kconfig | 572 ++++++++++++++++++++
drivers/mtd/nand/raw/Makefile | 62 +++
drivers/mtd/nand/{ => raw}/ams-delta.c | 0
drivers/mtd/nand/{ => raw}/atmel_nand.c | 0
drivers/mtd/nand/{ => raw}/atmel_nand_ecc.h | 0
drivers/mtd/nand/{ => raw}/atmel_nand_nfc.h | 0
drivers/mtd/nand/{ => raw}/au1550nd.c | 0
drivers/mtd/nand/{ => raw}/bcm47xxnflash/Makefile | 0
.../nand/{ => raw}/bcm47xxnflash/bcm47xxnflash.h | 0
drivers/mtd/nand/{ => raw}/bcm47xxnflash/main.c | 0
.../mtd/nand/{ => raw}/bcm47xxnflash/ops_bcm4706.c | 0
drivers/mtd/nand/{ => raw}/bf5xx_nand.c | 0
drivers/mtd/nand/{ => raw}/brcmnand/Makefile | 0
.../mtd/nand/{ => raw}/brcmnand/bcm63138_nand.c | 0
drivers/mtd/nand/{ => raw}/brcmnand/bcm6368_nand.c | 0
drivers/mtd/nand/{ => raw}/brcmnand/brcmnand.c | 0
drivers/mtd/nand/{ => raw}/brcmnand/brcmnand.h | 0
drivers/mtd/nand/{ => raw}/brcmnand/brcmstb_nand.c | 0
drivers/mtd/nand/{ => raw}/brcmnand/iproc_nand.c | 0
drivers/mtd/nand/{ => raw}/cafe_nand.c | 0
drivers/mtd/nand/{ => raw}/cmx270_nand.c | 0
drivers/mtd/nand/{ => raw}/cs553x_nand.c | 0
drivers/mtd/nand/{ => raw}/davinci_nand.c | 0
drivers/mtd/nand/{ => raw}/denali.c | 0
drivers/mtd/nand/{ => raw}/denali.h | 0
drivers/mtd/nand/{ => raw}/denali_dt.c | 0
drivers/mtd/nand/{ => raw}/denali_pci.c | 0
drivers/mtd/nand/{ => raw}/diskonchip.c | 0
drivers/mtd/nand/{ => raw}/docg4.c | 0
drivers/mtd/nand/{ => raw}/fsl_elbc_nand.c | 0
drivers/mtd/nand/{ => raw}/fsl_ifc_nand.c | 0
drivers/mtd/nand/{ => raw}/fsl_upm.c | 0
drivers/mtd/nand/{ => raw}/fsmc_nand.c | 0
drivers/mtd/nand/{ => raw}/gpio.c | 0
drivers/mtd/nand/{ => raw}/gpmi-nand/Makefile | 0
drivers/mtd/nand/{ => raw}/gpmi-nand/bch-regs.h | 0
drivers/mtd/nand/{ => raw}/gpmi-nand/gpmi-lib.c | 0
drivers/mtd/nand/{ => raw}/gpmi-nand/gpmi-nand.c | 0
drivers/mtd/nand/{ => raw}/gpmi-nand/gpmi-nand.h | 0
drivers/mtd/nand/{ => raw}/gpmi-nand/gpmi-regs.h | 0
drivers/mtd/nand/{ => raw}/hisi504_nand.c | 0
drivers/mtd/nand/{ => raw}/jz4740_nand.c | 0
drivers/mtd/nand/{ => raw}/jz4780_bch.c | 0
drivers/mtd/nand/{ => raw}/jz4780_bch.h | 0
drivers/mtd/nand/{ => raw}/jz4780_nand.c | 0
drivers/mtd/nand/{ => raw}/lpc32xx_mlc.c | 0
drivers/mtd/nand/{ => raw}/lpc32xx_slc.c | 0
drivers/mtd/nand/{ => raw}/mpc5121_nfc.c | 0
drivers/mtd/nand/{ => raw}/mtk_ecc.c | 0
drivers/mtd/nand/{ => raw}/mtk_ecc.h | 0
drivers/mtd/nand/{ => raw}/mtk_nand.c | 0
drivers/mtd/nand/{ => raw}/mxc_nand.c | 0
drivers/mtd/nand/{ => raw}/nand_base.c | 0
drivers/mtd/nand/{ => raw}/nand_bbt.c | 0
drivers/mtd/nand/{ => raw}/nand_bch.c | 0
drivers/mtd/nand/{ => raw}/nand_ecc.c | 0
drivers/mtd/nand/{ => raw}/nand_ids.c | 0
drivers/mtd/nand/{ => raw}/nand_timings.c | 0
drivers/mtd/nand/{ => raw}/nandsim.c | 0
drivers/mtd/nand/{ => raw}/ndfc.c | 0
drivers/mtd/nand/{ => raw}/nuc900_nand.c | 0
drivers/mtd/nand/{ => raw}/omap2.c | 0
drivers/mtd/nand/{ => raw}/omap_elm.c | 0
drivers/mtd/nand/{ => raw}/orion_nand.c | 0
drivers/mtd/nand/{ => raw}/pasemi_nand.c | 0
drivers/mtd/nand/{ => raw}/plat_nand.c | 0
drivers/mtd/nand/{ => raw}/pxa3xx_nand.c | 0
drivers/mtd/nand/{ => raw}/qcom_nandc.c | 0
drivers/mtd/nand/{ => raw}/r852.c | 0
drivers/mtd/nand/{ => raw}/r852.h | 0
drivers/mtd/nand/{ => raw}/s3c2410.c | 0
drivers/mtd/nand/{ => raw}/sh_flctl.c | 0
drivers/mtd/nand/{ => raw}/sharpsl.c | 0
drivers/mtd/nand/{ => raw}/sm_common.c | 0
drivers/mtd/nand/{ => raw}/sm_common.h | 0
drivers/mtd/nand/{ => raw}/socrates_nand.c | 0
drivers/mtd/nand/{ => raw}/sunxi_nand.c | 0
drivers/mtd/nand/{ => raw}/tmio_nand.c | 0
drivers/mtd/nand/{ => raw}/txx9ndfmc.c | 0
drivers/mtd/nand/{ => raw}/vf610_nfc.c | 0
drivers/mtd/nand/{ => raw}/xway_nand.c | 0
drivers/mtd/sm_ftl.c | 2 +-
84 files changed, 637 insertions(+), 635 deletions(-)
create mode 100644 drivers/mtd/nand/raw/Kconfig
create mode 100644 drivers/mtd/nand/raw/Makefile
rename drivers/mtd/nand/{ => raw}/ams-delta.c (100%)
rename drivers/mtd/nand/{ => raw}/atmel_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/atmel_nand_ecc.h (100%)
rename drivers/mtd/nand/{ => raw}/atmel_nand_nfc.h (100%)
rename drivers/mtd/nand/{ => raw}/au1550nd.c (100%)
rename drivers/mtd/nand/{ => raw}/bcm47xxnflash/Makefile (100%)
rename drivers/mtd/nand/{ => raw}/bcm47xxnflash/bcm47xxnflash.h (100%)
rename drivers/mtd/nand/{ => raw}/bcm47xxnflash/main.c (100%)
rename drivers/mtd/nand/{ => raw}/bcm47xxnflash/ops_bcm4706.c (100%)
rename drivers/mtd/nand/{ => raw}/bf5xx_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/brcmnand/Makefile (100%)
rename drivers/mtd/nand/{ => raw}/brcmnand/bcm63138_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/brcmnand/bcm6368_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/brcmnand/brcmnand.c (100%)
rename drivers/mtd/nand/{ => raw}/brcmnand/brcmnand.h (100%)
rename drivers/mtd/nand/{ => raw}/brcmnand/brcmstb_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/brcmnand/iproc_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/cafe_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/cmx270_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/cs553x_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/davinci_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/denali.c (100%)
rename drivers/mtd/nand/{ => raw}/denali.h (100%)
rename drivers/mtd/nand/{ => raw}/denali_dt.c (100%)
rename drivers/mtd/nand/{ => raw}/denali_pci.c (100%)
rename drivers/mtd/nand/{ => raw}/diskonchip.c (100%)
rename drivers/mtd/nand/{ => raw}/docg4.c (100%)
rename drivers/mtd/nand/{ => raw}/fsl_elbc_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/fsl_ifc_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/fsl_upm.c (100%)
rename drivers/mtd/nand/{ => raw}/fsmc_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/gpio.c (100%)
rename drivers/mtd/nand/{ => raw}/gpmi-nand/Makefile (100%)
rename drivers/mtd/nand/{ => raw}/gpmi-nand/bch-regs.h (100%)
rename drivers/mtd/nand/{ => raw}/gpmi-nand/gpmi-lib.c (100%)
rename drivers/mtd/nand/{ => raw}/gpmi-nand/gpmi-nand.c (100%)
rename drivers/mtd/nand/{ => raw}/gpmi-nand/gpmi-nand.h (100%)
rename drivers/mtd/nand/{ => raw}/gpmi-nand/gpmi-regs.h (100%)
rename drivers/mtd/nand/{ => raw}/hisi504_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/jz4740_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/jz4780_bch.c (100%)
rename drivers/mtd/nand/{ => raw}/jz4780_bch.h (100%)
rename drivers/mtd/nand/{ => raw}/jz4780_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/lpc32xx_mlc.c (100%)
rename drivers/mtd/nand/{ => raw}/lpc32xx_slc.c (100%)
rename drivers/mtd/nand/{ => raw}/mpc5121_nfc.c (100%)
rename drivers/mtd/nand/{ => raw}/mtk_ecc.c (100%)
rename drivers/mtd/nand/{ => raw}/mtk_ecc.h (100%)
rename drivers/mtd/nand/{ => raw}/mtk_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/mxc_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_base.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_bbt.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_bch.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_ecc.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_ids.c (100%)
rename drivers/mtd/nand/{ => raw}/nand_timings.c (100%)
rename drivers/mtd/nand/{ => raw}/nandsim.c (100%)
rename drivers/mtd/nand/{ => raw}/ndfc.c (100%)
rename drivers/mtd/nand/{ => raw}/nuc900_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/omap2.c (100%)
rename drivers/mtd/nand/{ => raw}/omap_elm.c (100%)
rename drivers/mtd/nand/{ => raw}/orion_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/pasemi_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/plat_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/pxa3xx_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/qcom_nandc.c (100%)
rename drivers/mtd/nand/{ => raw}/r852.c (100%)
rename drivers/mtd/nand/{ => raw}/r852.h (100%)
rename drivers/mtd/nand/{ => raw}/s3c2410.c (100%)
rename drivers/mtd/nand/{ => raw}/sh_flctl.c (100%)
rename drivers/mtd/nand/{ => raw}/sharpsl.c (100%)
rename drivers/mtd/nand/{ => raw}/sm_common.c (100%)
rename drivers/mtd/nand/{ => raw}/sm_common.h (100%)
rename drivers/mtd/nand/{ => raw}/socrates_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/sunxi_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/tmio_nand.c (100%)
rename drivers/mtd/nand/{ => raw}/txx9ndfmc.c (100%)
rename drivers/mtd/nand/{ => raw}/vf610_nfc.c (100%)
rename drivers/mtd/nand/{ => raw}/xway_nand.c (100%)
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 7b7a887b4709..6d5373471809 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -1,572 +1 @@
-config MTD_NAND_ECC
- tristate
-
-config MTD_NAND_ECC_SMC
- bool "NAND ECC Smart Media byte order"
- depends on MTD_NAND_ECC
- default n
- help
- Software ECC according to the Smart Media Specification.
- The original Linux implementation had byte 0 and 1 swapped.
-
-
-menuconfig MTD_NAND
- tristate "NAND Device Support"
- depends on MTD
- select MTD_NAND_IDS
- select MTD_NAND_ECC
- help
- This enables support for accessing all type of NAND flash
- devices. For further information see
- <http://www.linux-mtd.infradead.org/doc/nand.html>.
-
-if MTD_NAND
-
-config MTD_NAND_BCH
- tristate
- select BCH
- depends on MTD_NAND_ECC_BCH
- default MTD_NAND
-
-config MTD_NAND_ECC_BCH
- bool "Support software BCH ECC"
- default n
- help
- This enables support for software BCH error correction. Binary BCH
- codes are more powerful and cpu intensive than traditional Hamming
- ECC codes. They are used with NAND devices requiring more than 1 bit
- of error correction.
-
-config MTD_SM_COMMON
- tristate
- default n
-
-config MTD_NAND_DENALI
- tristate
-
-config MTD_NAND_DENALI_PCI
- tristate "Support Denali NAND controller on Intel Moorestown"
- select MTD_NAND_DENALI
- depends on HAS_DMA && PCI
- help
- Enable the driver for NAND flash on Intel Moorestown, using the
- Denali NAND controller core.
-
-config MTD_NAND_DENALI_DT
- tristate "Support Denali NAND controller as a DT device"
- select MTD_NAND_DENALI
- depends on HAS_DMA && HAVE_CLK && OF
- help
- Enable the driver for NAND flash on platforms using a Denali NAND
- controller as a DT device.
-
-config MTD_NAND_DENALI_SCRATCH_REG_ADDR
- hex "Denali NAND size scratch register address"
- default "0xFF108018"
- depends on MTD_NAND_DENALI_PCI
- help
- Some platforms place the NAND chip size in a scratch register
- because (some versions of) the driver aren't able to automatically
- determine the size of certain chips. Set the address of the
- scratch register here to enable this feature. On Intel Moorestown
- boards, the scratch register is at 0xFF108018.
-
-config MTD_NAND_GPIO
- tristate "GPIO assisted NAND Flash driver"
- depends on GPIOLIB || COMPILE_TEST
- depends on HAS_IOMEM
- help
- This enables a NAND flash driver where control signals are
- connected to GPIO pins, and commands and data are communicated
- via a memory mapped interface.
-
-config MTD_NAND_AMS_DELTA
- tristate "NAND Flash device on Amstrad E3"
- depends on MACH_AMS_DELTA
- default y
- help
- Support for NAND flash on Amstrad E3 (Delta).
-
-config MTD_NAND_OMAP2
- tristate "NAND Flash device on OMAP2, OMAP3, OMAP4 and Keystone"
- depends on (ARCH_OMAP2PLUS || ARCH_KEYSTONE)
- help
- Support for NAND flash on Texas Instruments OMAP2, OMAP3, OMAP4
- and Keystone platforms.
-
-config MTD_NAND_OMAP_BCH
- depends on MTD_NAND_OMAP2
- bool "Support hardware based BCH error correction"
- default n
- select BCH
- help
- This config enables the ELM hardware engine, which can be used to
- locate and correct errors when using BCH ECC scheme. This offloads
- the cpu from doing ECC error searching and correction. However some
- legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine
- so this is optional for them.
-
-config MTD_NAND_OMAP_BCH_BUILD
- def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH
-
-config MTD_NAND_IDS
- tristate
-
-config MTD_NAND_RICOH
- tristate "Ricoh xD card reader"
- default n
- depends on PCI
- select MTD_SM_COMMON
- help
- Enable support for Ricoh R5C852 xD card reader
- You also need to enable ether
- NAND SSFDC (SmartMedia) read only translation layer' or new
- expermental, readwrite
- 'SmartMedia/xD new translation layer'
-
-config MTD_NAND_AU1550
- tristate "Au1550/1200 NAND support"
- depends on MIPS_ALCHEMY
- help
- This enables the driver for the NAND flash controller on the
- AMD/Alchemy 1550 SOC.
-
-config MTD_NAND_BF5XX
- tristate "Blackfin on-chip NAND Flash Controller driver"
- depends on BF54x || BF52x
- help
- This enables the Blackfin on-chip NAND flash controller
-
- No board specific support is done by this driver, each board
- must advertise a platform_device for the driver to attach.
-
- This driver can also be built as a module. If so, the module
- will be called bf5xx-nand.
-
-config MTD_NAND_BF5XX_HWECC
- bool "BF5XX NAND Hardware ECC"
- default y
- depends on MTD_NAND_BF5XX
- help
- Enable the use of the BF5XX's internal ECC generator when
- using NAND.
-
-config MTD_NAND_BF5XX_BOOTROM_ECC
- bool "Use Blackfin BootROM ECC Layout"
- default n
- depends on MTD_NAND_BF5XX_HWECC
- help
- If you wish to modify NAND pages and allow the Blackfin on-chip
- BootROM to boot from them, say Y here. This is only necessary
- if you are booting U-Boot out of NAND and you wish to update
- U-Boot from Linux' userspace. Otherwise, you should say N here.
-
- If unsure, say N.
-
-config MTD_NAND_S3C2410
- tristate "NAND Flash support for Samsung S3C SoCs"
- depends on ARCH_S3C24XX || ARCH_S3C64XX
- help
- This enables the NAND flash controller on the S3C24xx and S3C64xx
- SoCs
-
- No board specific support is done by this driver, each board
- must advertise a platform_device for the driver to attach.
-
-config MTD_NAND_S3C2410_DEBUG
- bool "Samsung S3C NAND driver debug"
- depends on MTD_NAND_S3C2410
- help
- Enable debugging of the S3C NAND driver
-
-config MTD_NAND_S3C2410_HWECC
- bool "Samsung S3C NAND Hardware ECC"
- depends on MTD_NAND_S3C2410
- help
- Enable the use of the controller's internal ECC generator when
- using NAND. Early versions of the chips have had problems with
- incorrect ECC generation, and if using these, the default of
- software ECC is preferable.
-
-config MTD_NAND_NDFC
- tristate "NDFC NanD Flash Controller"
- depends on 4xx
- select MTD_NAND_ECC_SMC
- help
- NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs
-
-config MTD_NAND_S3C2410_CLKSTOP
- bool "Samsung S3C NAND IDLE clock stop"
- depends on MTD_NAND_S3C2410
- default n
- help
- Stop the clock to the NAND controller when there is no chip
- selected to save power. This will mean there is a small delay
- when the is NAND chip selected or released, but will save
- approximately 5mA of power when there is nothing happening.
-
-config MTD_NAND_DISKONCHIP
- tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)"
- depends on HAS_IOMEM
- select REED_SOLOMON
- select REED_SOLOMON_DEC16
- help
- This is a reimplementation of M-Systems DiskOnChip 2000,
- Millennium and Millennium Plus as a standard NAND device driver,
- as opposed to the earlier self-contained MTD device drivers.
- This should enable, among other things, proper JFFS2 operation on
- these devices.
-
-config MTD_NAND_DISKONCHIP_PROBE_ADVANCED
- bool "Advanced detection options for DiskOnChip"
- depends on MTD_NAND_DISKONCHIP
- help
- This option allows you to specify nonstandard address at which to
- probe for a DiskOnChip, or to change the detection options. You
- are unlikely to need any of this unless you are using LinuxBIOS.
- Say 'N'.
-
-config MTD_NAND_DISKONCHIP_PROBE_ADDRESS
- hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED
- depends on MTD_NAND_DISKONCHIP
- default "0"
- ---help---
- By default, the probe for DiskOnChip devices will look for a
- DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
- This option allows you to specify a single address at which to probe
- for the device, which is useful if you have other devices in that
- range which get upset when they are probed.
-
- (Note that on PowerPC, the normal probe will only check at
- 0xE4000000.)
-
- Normally, you should leave this set to zero, to allow the probe at
- the normal addresses.
-
-config MTD_NAND_DISKONCHIP_PROBE_HIGH
- bool "Probe high addresses"
- depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED
- help
- By default, the probe for DiskOnChip devices will look for a
- DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
- This option changes to make it probe between 0xFFFC8000 and
- 0xFFFEE000. Unless you are using LinuxBIOS, this is unlikely to be
- useful to you. Say 'N'.
-
-config MTD_NAND_DISKONCHIP_BBTWRITE
- bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP"
- depends on MTD_NAND_DISKONCHIP
- help
- On DiskOnChip devices shipped with the INFTL filesystem (Millennium
- and 2000 TSOP/Alon), Linux reserves some space at the end of the
- device for the Bad Block Table (BBT). If you have existing INFTL
- data on your device (created by non-Linux tools such as M-Systems'
- DOS drivers), your data might overlap the area Linux wants to use for
- the BBT. If this is a concern for you, leave this option disabled and
- Linux will not write BBT data into this area.
- The downside of leaving this option disabled is that if bad blocks
- are detected by Linux, they will not be recorded in the BBT, which
- could cause future problems.
- Once you enable this option, new filesystems (INFTL or others, created
- in Linux or other operating systems) will not use the reserved area.
- The only reason not to enable this option is to prevent damage to
- preexisting filesystems.
- Even if you leave this disabled, you can enable BBT writes at module
- load time (assuming you build diskonchip as a module) with the module
- parameter "inftl_bbt_write=1".
-
-config MTD_NAND_DOCG4
- tristate "Support for DiskOnChip G4"
- depends on HAS_IOMEM
- select BCH
- select BITREVERSE
- help
- Support for diskonchip G4 nand flash, found in various smartphones and
- PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba
- Portege G900, Asus P526, and O2 XDA Zinc.
-
- With this driver you will be able to use UBI and create a ubifs on the
- device, so you may wish to consider enabling UBI and UBIFS as well.
-
- These devices ship with the Mys/Sandisk SAFTL formatting, for which
- there is currently no mtd parser, so you may want to use command line
- partitioning to segregate write-protected blocks. On the Treo680, the
- first five erase blocks (256KiB each) are write-protected, followed
- by the block containing the saftl partition table. This is probably
- typical.
-
-config MTD_NAND_SHARPSL
- tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
- depends on ARCH_PXA
-
-config MTD_NAND_CAFE
- tristate "NAND support for OLPC CAFÉ chip"
- depends on PCI
- select REED_SOLOMON
- select REED_SOLOMON_DEC16
- help
- Use NAND flash attached to the CAFÉ chip designed for the OLPC
- laptop.
-
-config MTD_NAND_CS553X
- tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)"
- depends on X86_32
- depends on !UML && HAS_IOMEM
- help
- The CS553x companion chips for the AMD Geode processor
- include NAND flash controllers with built-in hardware ECC
- capabilities; enabling this option will allow you to use
- these. The driver will check the MSRs to verify that the
- controller is enabled for NAND, and currently requires that
- the controller be in MMIO mode.
-
- If you say "m", the module will be called cs553x_nand.
-
-config MTD_NAND_ATMEL
- tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32"
- depends on ARCH_AT91 || AVR32
- help
- Enables support for NAND Flash / Smart Media Card interface
- on Atmel AT91 and AVR32 processors.
-
-config MTD_NAND_PXA3xx
- tristate "NAND support on PXA3xx and Armada 370/XP"
- depends on PXA3xx || ARCH_MMP || PLAT_ORION
- help
- This enables the driver for the NAND flash device found on
- PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
-
-config MTD_NAND_SLC_LPC32XX
- tristate "NXP LPC32xx SLC Controller"
- depends on ARCH_LPC32XX
- help
- Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell
- chips) NAND controller. This is the default for the PHYTEC 3250
- reference board which contains a NAND256R3A2CZA6 chip.
-
- Please check the actual NAND chip connected and its support
- by the SLC NAND controller.
-
-config MTD_NAND_MLC_LPC32XX
- tristate "NXP LPC32xx MLC Controller"
- depends on ARCH_LPC32XX
- help
- Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND
- controller. This is the default for the WORK92105 controller
- board.
-
- Please check the actual NAND chip connected and its support
- by the MLC NAND controller.
-
-config MTD_NAND_CM_X270
- tristate "Support for NAND Flash on CM-X270 modules"
- depends on MACH_ARMCORE
-
-config MTD_NAND_PASEMI
- tristate "NAND support for PA Semi PWRficient"
- depends on PPC_PASEMI
- help
- Enables support for NAND Flash interface on PA Semi PWRficient
- based boards
-
-config MTD_NAND_TMIO
- tristate "NAND Flash device on Toshiba Mobile IO Controller"
- depends on MFD_TMIO
- help
- Support for NAND flash connected to a Toshiba Mobile IO
- Controller in some PDAs, including the Sharp SL6000x.
-
-config MTD_NAND_NANDSIM
- tristate "Support for NAND Flash Simulator"
- help
- The simulator may simulate various NAND flash chips for the
- MTD nand layer.
-
-config MTD_NAND_GPMI_NAND
- tristate "GPMI NAND Flash Controller driver"
- depends on MTD_NAND && MXS_DMA
- help
- Enables NAND Flash support for IMX23, IMX28 or IMX6.
- The GPMI controller is very powerful, with the help of BCH
- module, it can do the hardware ECC. The GPMI supports several
- NAND flashs at the same time. The GPMI may conflicts with other
- block, such as SD card. So pay attention to it when you enable
- the GPMI.
-
-config MTD_NAND_BRCMNAND
- tristate "Broadcom STB NAND controller"
- depends on ARM || ARM64 || MIPS
- help
- Enables the Broadcom NAND controller driver. The controller was
- originally designed for Set-Top Box but is used on various BCM7xxx,
- BCM3xxx, BCM63xxx, iProc/Cygnus and more.
-
-config MTD_NAND_BCM47XXNFLASH
- tristate "Support for NAND flash on BCM4706 BCMA bus"
- depends on BCMA_NFLASH
- help
- BCMA bus can have various flash memories attached, they are
- registered by bcma as platform devices. This enables driver for
- NAND flash memories. For now only BCM4706 is supported.
-
-config MTD_NAND_PLATFORM
- tristate "Support for generic platform NAND driver"
- depends on HAS_IOMEM
- help
- This implements a generic NAND driver for on-SOC platform
- devices. You will need to provide platform-specific functions
- via platform_data.
-
-config MTD_NAND_ORION
- tristate "NAND Flash support for Marvell Orion SoC"
- depends on PLAT_ORION
- help
- This enables the NAND flash controller on Orion machines.
-
- No board specific support is done by this driver, each board
- must advertise a platform_device for the driver to attach.
-
-config MTD_NAND_FSL_ELBC
- tristate "NAND support for Freescale eLBC controllers"
- depends on FSL_SOC
- select FSL_LBC
- help
- Various Freescale chips, including the 8313, include a NAND Flash
- Controller Module with built-in hardware ECC capabilities.
- Enabling this option will enable you to use this to control
- external NAND devices.
-
-config MTD_NAND_FSL_IFC
- tristate "NAND support for Freescale IFC controller"
- depends on FSL_SOC || ARCH_LAYERSCAPE
- select FSL_IFC
- select MEMORY
- help
- Various Freescale chips e.g P1010, include a NAND Flash machine
- with built-in hardware ECC capabilities.
- Enabling this option will enable you to use this to control
- external NAND devices.
-
-config MTD_NAND_FSL_UPM
- tristate "Support for NAND on Freescale UPM"
- depends on PPC_83xx || PPC_85xx
- select FSL_LBC
- help
- Enables support for NAND Flash chips wired onto Freescale PowerPC
- processor localbus with User-Programmable Machine support.
-
-config MTD_NAND_MPC5121_NFC
- tristate "MPC5121 built-in NAND Flash Controller support"
- depends on PPC_MPC512x
- help
- This enables the driver for the NAND flash controller on the
- MPC5121 SoC.
-
-config MTD_NAND_VF610_NFC
- tristate "Support for Freescale NFC for VF610/MPC5125"
- depends on (SOC_VF610 || COMPILE_TEST)
- depends on HAS_IOMEM
- help
- Enables support for NAND Flash Controller on some Freescale
- processors like the VF610, MPC5125, MCF54418 or Kinetis K70.
- The driver supports a maximum 2k page size. With 2k pages and
- 64 bytes or more of OOB, hardware ECC with up to 32-bit error
- correction is supported. Hardware ECC is only enabled through
- device tree.
-
-config MTD_NAND_MXC
- tristate "MXC NAND support"
- depends on ARCH_MXC
- help
- This enables the driver for the NAND flash controller on the
- MXC processors.
-
-config MTD_NAND_SH_FLCTL
- tristate "Support for NAND on Renesas SuperH FLCTL"
- depends on SUPERH || COMPILE_TEST
- depends on HAS_IOMEM
- depends on HAS_DMA
- help
- Several Renesas SuperH CPU has FLCTL. This option enables support
- for NAND Flash using FLCTL.
-
-config MTD_NAND_DAVINCI
- tristate "Support NAND on DaVinci/Keystone SoC"
- depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF)
- help
- Enable the driver for NAND flash chips on Texas Instruments
- DaVinci/Keystone processors.
-
-config MTD_NAND_TXX9NDFMC
- tristate "NAND Flash support for TXx9 SoC"
- depends on SOC_TX4938 || SOC_TX4939
- help
- This enables the NAND flash controller on the TXx9 SoCs.
-
-config MTD_NAND_SOCRATES
- tristate "Support for NAND on Socrates board"
- depends on SOCRATES
- help
- Enables support for NAND Flash chips wired onto Socrates board.
-
-config MTD_NAND_NUC900
- tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards."
- depends on ARCH_W90X900
- help
- This enables the driver for the NAND Flash on evaluation board based
- on w90p910 / NUC9xx.
-
-config MTD_NAND_JZ4740
- tristate "Support for JZ4740 SoC NAND controller"
- depends on MACH_JZ4740
- help
- Enables support for NAND Flash on JZ4740 SoC based boards.
-
-config MTD_NAND_JZ4780
- tristate "Support for NAND on JZ4780 SoC"
- depends on MACH_JZ4780 && JZ4780_NEMC
- help
- Enables support for NAND Flash connected to the NEMC on JZ4780 SoC
- based boards, using the BCH controller for hardware error correction.
-
-config MTD_NAND_FSMC
- tristate "Support for NAND on ST Micros FSMC"
- depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300
- help
- Enables support for NAND Flash chips on the ST Microelectronics
- Flexible Static Memory Controller (FSMC)
-
-config MTD_NAND_XWAY
- tristate "Support for NAND on Lantiq XWAY SoC"
- depends on LANTIQ && SOC_TYPE_XWAY
- help
- Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached
- to the External Bus Unit (EBU).
-
-config MTD_NAND_SUNXI
- tristate "Support for NAND on Allwinner SoCs"
- depends on ARCH_SUNXI
- help
- Enables support for NAND Flash chips on Allwinner SoCs.
-
-config MTD_NAND_HISI504
- tristate "Support for NAND controller on Hisilicon SoC Hip04"
- depends on HAS_DMA
- help
- Enables support for NAND controller on Hisilicon SoC Hip04.
-
-config MTD_NAND_QCOM
- tristate "Support for NAND on QCOM SoCs"
- depends on ARCH_QCOM
- help
- Enables support for NAND flash chips on SoCs containing the EBI2 NAND
- controller. This controller is found on IPQ806x SoC.
-
-config MTD_NAND_MTK
- tristate "Support for NAND controller on MTK SoCs"
- depends on HAS_DMA
- help
- Enables support for NAND controller on MTK SoCs.
- This controller is found on mt27xx, mt81xx, mt65xx SoCs.
-
-endif # MTD_NAND
+source "drivers/mtd/nand/raw/Kconfig"
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index cafde6f3d957..eee2f27e92fc 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -1,62 +1 @@
-#
-# linux/drivers/nand/Makefile
-#
-
-obj-$(CONFIG_MTD_NAND) += nand.o
-obj-$(CONFIG_MTD_NAND_ECC) += nand_ecc.o
-obj-$(CONFIG_MTD_NAND_BCH) += nand_bch.o
-obj-$(CONFIG_MTD_NAND_IDS) += nand_ids.o
-obj-$(CONFIG_MTD_SM_COMMON) += sm_common.o
-
-obj-$(CONFIG_MTD_NAND_CAFE) += cafe_nand.o
-obj-$(CONFIG_MTD_NAND_AMS_DELTA) += ams-delta.o
-obj-$(CONFIG_MTD_NAND_DENALI) += denali.o
-obj-$(CONFIG_MTD_NAND_DENALI_PCI) += denali_pci.o
-obj-$(CONFIG_MTD_NAND_DENALI_DT) += denali_dt.o
-obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o
-obj-$(CONFIG_MTD_NAND_BF5XX) += bf5xx_nand.o
-obj-$(CONFIG_MTD_NAND_S3C2410) += s3c2410.o
-obj-$(CONFIG_MTD_NAND_DAVINCI) += davinci_nand.o
-obj-$(CONFIG_MTD_NAND_DISKONCHIP) += diskonchip.o
-obj-$(CONFIG_MTD_NAND_DOCG4) += docg4.o
-obj-$(CONFIG_MTD_NAND_FSMC) += fsmc_nand.o
-obj-$(CONFIG_MTD_NAND_SHARPSL) += sharpsl.o
-obj-$(CONFIG_MTD_NAND_NANDSIM) += nandsim.o
-obj-$(CONFIG_MTD_NAND_CS553X) += cs553x_nand.o
-obj-$(CONFIG_MTD_NAND_NDFC) += ndfc.o
-obj-$(CONFIG_MTD_NAND_ATMEL) += atmel_nand.o
-obj-$(CONFIG_MTD_NAND_GPIO) += gpio.o
-omap2_nand-objs := omap2.o
-obj-$(CONFIG_MTD_NAND_OMAP2) += omap2_nand.o
-obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD) += omap_elm.o
-obj-$(CONFIG_MTD_NAND_CM_X270) += cmx270_nand.o
-obj-$(CONFIG_MTD_NAND_PXA3xx) += pxa3xx_nand.o
-obj-$(CONFIG_MTD_NAND_TMIO) += tmio_nand.o
-obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o
-obj-$(CONFIG_MTD_NAND_PASEMI) += pasemi_nand.o
-obj-$(CONFIG_MTD_NAND_ORION) += orion_nand.o
-obj-$(CONFIG_MTD_NAND_FSL_ELBC) += fsl_elbc_nand.o
-obj-$(CONFIG_MTD_NAND_FSL_IFC) += fsl_ifc_nand.o
-obj-$(CONFIG_MTD_NAND_FSL_UPM) += fsl_upm.o
-obj-$(CONFIG_MTD_NAND_SLC_LPC32XX) += lpc32xx_slc.o
-obj-$(CONFIG_MTD_NAND_MLC_LPC32XX) += lpc32xx_mlc.o
-obj-$(CONFIG_MTD_NAND_SH_FLCTL) += sh_flctl.o
-obj-$(CONFIG_MTD_NAND_MXC) += mxc_nand.o
-obj-$(CONFIG_MTD_NAND_SOCRATES) += socrates_nand.o
-obj-$(CONFIG_MTD_NAND_TXX9NDFMC) += txx9ndfmc.o
-obj-$(CONFIG_MTD_NAND_NUC900) += nuc900_nand.o
-obj-$(CONFIG_MTD_NAND_MPC5121_NFC) += mpc5121_nfc.o
-obj-$(CONFIG_MTD_NAND_VF610_NFC) += vf610_nfc.o
-obj-$(CONFIG_MTD_NAND_RICOH) += r852.o
-obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
-obj-$(CONFIG_MTD_NAND_JZ4780) += jz4780_nand.o jz4780_bch.o
-obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi-nand/
-obj-$(CONFIG_MTD_NAND_XWAY) += xway_nand.o
-obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash/
-obj-$(CONFIG_MTD_NAND_SUNXI) += sunxi_nand.o
-obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o
-obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand/
-obj-$(CONFIG_MTD_NAND_QCOM) += qcom_nandc.o
-obj-$(CONFIG_MTD_NAND_MTK) += mtk_nand.o mtk_ecc.o
-
-nand-objs := nand_base.o nand_bbt.o nand_timings.o
+obj-y += raw/
diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
new file mode 100644
index 000000000000..7b7a887b4709
--- /dev/null
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -0,0 +1,572 @@
+config MTD_NAND_ECC
+ tristate
+
+config MTD_NAND_ECC_SMC
+ bool "NAND ECC Smart Media byte order"
+ depends on MTD_NAND_ECC
+ default n
+ help
+ Software ECC according to the Smart Media Specification.
+ The original Linux implementation had byte 0 and 1 swapped.
+
+
+menuconfig MTD_NAND
+ tristate "NAND Device Support"
+ depends on MTD
+ select MTD_NAND_IDS
+ select MTD_NAND_ECC
+ help
+ This enables support for accessing all type of NAND flash
+ devices. For further information see
+ <http://www.linux-mtd.infradead.org/doc/nand.html>.
+
+if MTD_NAND
+
+config MTD_NAND_BCH
+ tristate
+ select BCH
+ depends on MTD_NAND_ECC_BCH
+ default MTD_NAND
+
+config MTD_NAND_ECC_BCH
+ bool "Support software BCH ECC"
+ default n
+ help
+ This enables support for software BCH error correction. Binary BCH
+ codes are more powerful and cpu intensive than traditional Hamming
+ ECC codes. They are used with NAND devices requiring more than 1 bit
+ of error correction.
+
+config MTD_SM_COMMON
+ tristate
+ default n
+
+config MTD_NAND_DENALI
+ tristate
+
+config MTD_NAND_DENALI_PCI
+ tristate "Support Denali NAND controller on Intel Moorestown"
+ select MTD_NAND_DENALI
+ depends on HAS_DMA && PCI
+ help
+ Enable the driver for NAND flash on Intel Moorestown, using the
+ Denali NAND controller core.
+
+config MTD_NAND_DENALI_DT
+ tristate "Support Denali NAND controller as a DT device"
+ select MTD_NAND_DENALI
+ depends on HAS_DMA && HAVE_CLK && OF
+ help
+ Enable the driver for NAND flash on platforms using a Denali NAND
+ controller as a DT device.
+
+config MTD_NAND_DENALI_SCRATCH_REG_ADDR
+ hex "Denali NAND size scratch register address"
+ default "0xFF108018"
+ depends on MTD_NAND_DENALI_PCI
+ help
+ Some platforms place the NAND chip size in a scratch register
+ because (some versions of) the driver aren't able to automatically
+ determine the size of certain chips. Set the address of the
+ scratch register here to enable this feature. On Intel Moorestown
+ boards, the scratch register is at 0xFF108018.
+
+config MTD_NAND_GPIO
+ tristate "GPIO assisted NAND Flash driver"
+ depends on GPIOLIB || COMPILE_TEST
+ depends on HAS_IOMEM
+ help
+ This enables a NAND flash driver where control signals are
+ connected to GPIO pins, and commands and data are communicated
+ via a memory mapped interface.
+
+config MTD_NAND_AMS_DELTA
+ tristate "NAND Flash device on Amstrad E3"
+ depends on MACH_AMS_DELTA
+ default y
+ help
+ Support for NAND flash on Amstrad E3 (Delta).
+
+config MTD_NAND_OMAP2
+ tristate "NAND Flash device on OMAP2, OMAP3, OMAP4 and Keystone"
+ depends on (ARCH_OMAP2PLUS || ARCH_KEYSTONE)
+ help
+ Support for NAND flash on Texas Instruments OMAP2, OMAP3, OMAP4
+ and Keystone platforms.
+
+config MTD_NAND_OMAP_BCH
+ depends on MTD_NAND_OMAP2
+ bool "Support hardware based BCH error correction"
+ default n
+ select BCH
+ help
+ This config enables the ELM hardware engine, which can be used to
+ locate and correct errors when using BCH ECC scheme. This offloads
+ the cpu from doing ECC error searching and correction. However some
+ legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine
+ so this is optional for them.
+
+config MTD_NAND_OMAP_BCH_BUILD
+ def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH
+
+config MTD_NAND_IDS
+ tristate
+
+config MTD_NAND_RICOH
+ tristate "Ricoh xD card reader"
+ default n
+ depends on PCI
+ select MTD_SM_COMMON
+ help
+ Enable support for Ricoh R5C852 xD card reader
+ You also need to enable ether
+ NAND SSFDC (SmartMedia) read only translation layer' or new
+ expermental, readwrite
+ 'SmartMedia/xD new translation layer'
+
+config MTD_NAND_AU1550
+ tristate "Au1550/1200 NAND support"
+ depends on MIPS_ALCHEMY
+ help
+ This enables the driver for the NAND flash controller on the
+ AMD/Alchemy 1550 SOC.
+
+config MTD_NAND_BF5XX
+ tristate "Blackfin on-chip NAND Flash Controller driver"
+ depends on BF54x || BF52x
+ help
+ This enables the Blackfin on-chip NAND flash controller
+
+ No board specific support is done by this driver, each board
+ must advertise a platform_device for the driver to attach.
+
+ This driver can also be built as a module. If so, the module
+ will be called bf5xx-nand.
+
+config MTD_NAND_BF5XX_HWECC
+ bool "BF5XX NAND Hardware ECC"
+ default y
+ depends on MTD_NAND_BF5XX
+ help
+ Enable the use of the BF5XX's internal ECC generator when
+ using NAND.
+
+config MTD_NAND_BF5XX_BOOTROM_ECC
+ bool "Use Blackfin BootROM ECC Layout"
+ default n
+ depends on MTD_NAND_BF5XX_HWECC
+ help
+ If you wish to modify NAND pages and allow the Blackfin on-chip
+ BootROM to boot from them, say Y here. This is only necessary
+ if you are booting U-Boot out of NAND and you wish to update
+ U-Boot from Linux' userspace. Otherwise, you should say N here.
+
+ If unsure, say N.
+
+config MTD_NAND_S3C2410
+ tristate "NAND Flash support for Samsung S3C SoCs"
+ depends on ARCH_S3C24XX || ARCH_S3C64XX
+ help
+ This enables the NAND flash controller on the S3C24xx and S3C64xx
+ SoCs
+
+ No board specific support is done by this driver, each board
+ must advertise a platform_device for the driver to attach.
+
+config MTD_NAND_S3C2410_DEBUG
+ bool "Samsung S3C NAND driver debug"
+ depends on MTD_NAND_S3C2410
+ help
+ Enable debugging of the S3C NAND driver
+
+config MTD_NAND_S3C2410_HWECC
+ bool "Samsung S3C NAND Hardware ECC"
+ depends on MTD_NAND_S3C2410
+ help
+ Enable the use of the controller's internal ECC generator when
+ using NAND. Early versions of the chips have had problems with
+ incorrect ECC generation, and if using these, the default of
+ software ECC is preferable.
+
+config MTD_NAND_NDFC
+ tristate "NDFC NanD Flash Controller"
+ depends on 4xx
+ select MTD_NAND_ECC_SMC
+ help
+ NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs
+
+config MTD_NAND_S3C2410_CLKSTOP
+ bool "Samsung S3C NAND IDLE clock stop"
+ depends on MTD_NAND_S3C2410
+ default n
+ help
+ Stop the clock to the NAND controller when there is no chip
+ selected to save power. This will mean there is a small delay
+ when the is NAND chip selected or released, but will save
+ approximately 5mA of power when there is nothing happening.
+
+config MTD_NAND_DISKONCHIP
+ tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)"
+ depends on HAS_IOMEM
+ select REED_SOLOMON
+ select REED_SOLOMON_DEC16
+ help
+ This is a reimplementation of M-Systems DiskOnChip 2000,
+ Millennium and Millennium Plus as a standard NAND device driver,
+ as opposed to the earlier self-contained MTD device drivers.
+ This should enable, among other things, proper JFFS2 operation on
+ these devices.
+
+config MTD_NAND_DISKONCHIP_PROBE_ADVANCED
+ bool "Advanced detection options for DiskOnChip"
+ depends on MTD_NAND_DISKONCHIP
+ help
+ This option allows you to specify nonstandard address at which to
+ probe for a DiskOnChip, or to change the detection options. You
+ are unlikely to need any of this unless you are using LinuxBIOS.
+ Say 'N'.
+
+config MTD_NAND_DISKONCHIP_PROBE_ADDRESS
+ hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED
+ depends on MTD_NAND_DISKONCHIP
+ default "0"
+ ---help---
+ By default, the probe for DiskOnChip devices will look for a
+ DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
+ This option allows you to specify a single address at which to probe
+ for the device, which is useful if you have other devices in that
+ range which get upset when they are probed.
+
+ (Note that on PowerPC, the normal probe will only check at
+ 0xE4000000.)
+
+ Normally, you should leave this set to zero, to allow the probe at
+ the normal addresses.
+
+config MTD_NAND_DISKONCHIP_PROBE_HIGH
+ bool "Probe high addresses"
+ depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED
+ help
+ By default, the probe for DiskOnChip devices will look for a
+ DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
+ This option changes to make it probe between 0xFFFC8000 and
+ 0xFFFEE000. Unless you are using LinuxBIOS, this is unlikely to be
+ useful to you. Say 'N'.
+
+config MTD_NAND_DISKONCHIP_BBTWRITE
+ bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP"
+ depends on MTD_NAND_DISKONCHIP
+ help
+ On DiskOnChip devices shipped with the INFTL filesystem (Millennium
+ and 2000 TSOP/Alon), Linux reserves some space at the end of the
+ device for the Bad Block Table (BBT). If you have existing INFTL
+ data on your device (created by non-Linux tools such as M-Systems'
+ DOS drivers), your data might overlap the area Linux wants to use for
+ the BBT. If this is a concern for you, leave this option disabled and
+ Linux will not write BBT data into this area.
+ The downside of leaving this option disabled is that if bad blocks
+ are detected by Linux, they will not be recorded in the BBT, which
+ could cause future problems.
+ Once you enable this option, new filesystems (INFTL or others, created
+ in Linux or other operating systems) will not use the reserved area.
+ The only reason not to enable this option is to prevent damage to
+ preexisting filesystems.
+ Even if you leave this disabled, you can enable BBT writes at module
+ load time (assuming you build diskonchip as a module) with the module
+ parameter "inftl_bbt_write=1".
+
+config MTD_NAND_DOCG4
+ tristate "Support for DiskOnChip G4"
+ depends on HAS_IOMEM
+ select BCH
+ select BITREVERSE
+ help
+ Support for diskonchip G4 nand flash, found in various smartphones and
+ PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba
+ Portege G900, Asus P526, and O2 XDA Zinc.
+
+ With this driver you will be able to use UBI and create a ubifs on the
+ device, so you may wish to consider enabling UBI and UBIFS as well.
+
+ These devices ship with the Mys/Sandisk SAFTL formatting, for which
+ there is currently no mtd parser, so you may want to use command line
+ partitioning to segregate write-protected blocks. On the Treo680, the
+ first five erase blocks (256KiB each) are write-protected, followed
+ by the block containing the saftl partition table. This is probably
+ typical.
+
+config MTD_NAND_SHARPSL
+ tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
+ depends on ARCH_PXA
+
+config MTD_NAND_CAFE
+ tristate "NAND support for OLPC CAFÉ chip"
+ depends on PCI
+ select REED_SOLOMON
+ select REED_SOLOMON_DEC16
+ help
+ Use NAND flash attached to the CAFÉ chip designed for the OLPC
+ laptop.
+
+config MTD_NAND_CS553X
+ tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)"
+ depends on X86_32
+ depends on !UML && HAS_IOMEM
+ help
+ The CS553x companion chips for the AMD Geode processor
+ include NAND flash controllers with built-in hardware ECC
+ capabilities; enabling this option will allow you to use
+ these. The driver will check the MSRs to verify that the
+ controller is enabled for NAND, and currently requires that
+ the controller be in MMIO mode.
+
+ If you say "m", the module will be called cs553x_nand.
+
+config MTD_NAND_ATMEL
+ tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32"
+ depends on ARCH_AT91 || AVR32
+ help
+ Enables support for NAND Flash / Smart Media Card interface
+ on Atmel AT91 and AVR32 processors.
+
+config MTD_NAND_PXA3xx
+ tristate "NAND support on PXA3xx and Armada 370/XP"
+ depends on PXA3xx || ARCH_MMP || PLAT_ORION
+ help
+ This enables the driver for the NAND flash device found on
+ PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
+
+config MTD_NAND_SLC_LPC32XX
+ tristate "NXP LPC32xx SLC Controller"
+ depends on ARCH_LPC32XX
+ help
+ Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell
+ chips) NAND controller. This is the default for the PHYTEC 3250
+ reference board which contains a NAND256R3A2CZA6 chip.
+
+ Please check the actual NAND chip connected and its support
+ by the SLC NAND controller.
+
+config MTD_NAND_MLC_LPC32XX
+ tristate "NXP LPC32xx MLC Controller"
+ depends on ARCH_LPC32XX
+ help
+ Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND
+ controller. This is the default for the WORK92105 controller
+ board.
+
+ Please check the actual NAND chip connected and its support
+ by the MLC NAND controller.
+
+config MTD_NAND_CM_X270
+ tristate "Support for NAND Flash on CM-X270 modules"
+ depends on MACH_ARMCORE
+
+config MTD_NAND_PASEMI
+ tristate "NAND support for PA Semi PWRficient"
+ depends on PPC_PASEMI
+ help
+ Enables support for NAND Flash interface on PA Semi PWRficient
+ based boards
+
+config MTD_NAND_TMIO
+ tristate "NAND Flash device on Toshiba Mobile IO Controller"
+ depends on MFD_TMIO
+ help
+ Support for NAND flash connected to a Toshiba Mobile IO
+ Controller in some PDAs, including the Sharp SL6000x.
+
+config MTD_NAND_NANDSIM
+ tristate "Support for NAND Flash Simulator"
+ help
+ The simulator may simulate various NAND flash chips for the
+ MTD nand layer.
+
+config MTD_NAND_GPMI_NAND
+ tristate "GPMI NAND Flash Controller driver"
+ depends on MTD_NAND && MXS_DMA
+ help
+ Enables NAND Flash support for IMX23, IMX28 or IMX6.
+ The GPMI controller is very powerful, with the help of BCH
+ module, it can do the hardware ECC. The GPMI supports several
+ NAND flashs at the same time. The GPMI may conflicts with other
+ block, such as SD card. So pay attention to it when you enable
+ the GPMI.
+
+config MTD_NAND_BRCMNAND
+ tristate "Broadcom STB NAND controller"
+ depends on ARM || ARM64 || MIPS
+ help
+ Enables the Broadcom NAND controller driver. The controller was
+ originally designed for Set-Top Box but is used on various BCM7xxx,
+ BCM3xxx, BCM63xxx, iProc/Cygnus and more.
+
+config MTD_NAND_BCM47XXNFLASH
+ tristate "Support for NAND flash on BCM4706 BCMA bus"
+ depends on BCMA_NFLASH
+ help
+ BCMA bus can have various flash memories attached, they are
+ registered by bcma as platform devices. This enables driver for
+ NAND flash memories. For now only BCM4706 is supported.
+
+config MTD_NAND_PLATFORM
+ tristate "Support for generic platform NAND driver"
+ depends on HAS_IOMEM
+ help
+ This implements a generic NAND driver for on-SOC platform
+ devices. You will need to provide platform-specific functions
+ via platform_data.
+
+config MTD_NAND_ORION
+ tristate "NAND Flash support for Marvell Orion SoC"
+ depends on PLAT_ORION
+ help
+ This enables the NAND flash controller on Orion machines.
+
+ No board specific support is done by this driver, each board
+ must advertise a platform_device for the driver to attach.
+
+config MTD_NAND_FSL_ELBC
+ tristate "NAND support for Freescale eLBC controllers"
+ depends on FSL_SOC
+ select FSL_LBC
+ help
+ Various Freescale chips, including the 8313, include a NAND Flash
+ Controller Module with built-in hardware ECC capabilities.
+ Enabling this option will enable you to use this to control
+ external NAND devices.
+
+config MTD_NAND_FSL_IFC
+ tristate "NAND support for Freescale IFC controller"
+ depends on FSL_SOC || ARCH_LAYERSCAPE
+ select FSL_IFC
+ select MEMORY
+ help
+ Various Freescale chips e.g P1010, include a NAND Flash machine
+ with built-in hardware ECC capabilities.
+ Enabling this option will enable you to use this to control
+ external NAND devices.
+
+config MTD_NAND_FSL_UPM
+ tristate "Support for NAND on Freescale UPM"
+ depends on PPC_83xx || PPC_85xx
+ select FSL_LBC
+ help
+ Enables support for NAND Flash chips wired onto Freescale PowerPC
+ processor localbus with User-Programmable Machine support.
+
+config MTD_NAND_MPC5121_NFC
+ tristate "MPC5121 built-in NAND Flash Controller support"
+ depends on PPC_MPC512x
+ help
+ This enables the driver for the NAND flash controller on the
+ MPC5121 SoC.
+
+config MTD_NAND_VF610_NFC
+ tristate "Support for Freescale NFC for VF610/MPC5125"
+ depends on (SOC_VF610 || COMPILE_TEST)
+ depends on HAS_IOMEM
+ help
+ Enables support for NAND Flash Controller on some Freescale
+ processors like the VF610, MPC5125, MCF54418 or Kinetis K70.
+ The driver supports a maximum 2k page size. With 2k pages and
+ 64 bytes or more of OOB, hardware ECC with up to 32-bit error
+ correction is supported. Hardware ECC is only enabled through
+ device tree.
+
+config MTD_NAND_MXC
+ tristate "MXC NAND support"
+ depends on ARCH_MXC
+ help
+ This enables the driver for the NAND flash controller on the
+ MXC processors.
+
+config MTD_NAND_SH_FLCTL
+ tristate "Support for NAND on Renesas SuperH FLCTL"
+ depends on SUPERH || COMPILE_TEST
+ depends on HAS_IOMEM
+ depends on HAS_DMA
+ help
+ Several Renesas SuperH CPU has FLCTL. This option enables support
+ for NAND Flash using FLCTL.
+
+config MTD_NAND_DAVINCI
+ tristate "Support NAND on DaVinci/Keystone SoC"
+ depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF)
+ help
+ Enable the driver for NAND flash chips on Texas Instruments
+ DaVinci/Keystone processors.
+
+config MTD_NAND_TXX9NDFMC
+ tristate "NAND Flash support for TXx9 SoC"
+ depends on SOC_TX4938 || SOC_TX4939
+ help
+ This enables the NAND flash controller on the TXx9 SoCs.
+
+config MTD_NAND_SOCRATES
+ tristate "Support for NAND on Socrates board"
+ depends on SOCRATES
+ help
+ Enables support for NAND Flash chips wired onto Socrates board.
+
+config MTD_NAND_NUC900
+ tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards."
+ depends on ARCH_W90X900
+ help
+ This enables the driver for the NAND Flash on evaluation board based
+ on w90p910 / NUC9xx.
+
+config MTD_NAND_JZ4740
+ tristate "Support for JZ4740 SoC NAND controller"
+ depends on MACH_JZ4740
+ help
+ Enables support for NAND Flash on JZ4740 SoC based boards.
+
+config MTD_NAND_JZ4780
+ tristate "Support for NAND on JZ4780 SoC"
+ depends on MACH_JZ4780 && JZ4780_NEMC
+ help
+ Enables support for NAND Flash connected to the NEMC on JZ4780 SoC
+ based boards, using the BCH controller for hardware error correction.
+
+config MTD_NAND_FSMC
+ tristate "Support for NAND on ST Micros FSMC"
+ depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300
+ help
+ Enables support for NAND Flash chips on the ST Microelectronics
+ Flexible Static Memory Controller (FSMC)
+
+config MTD_NAND_XWAY
+ tristate "Support for NAND on Lantiq XWAY SoC"
+ depends on LANTIQ && SOC_TYPE_XWAY
+ help
+ Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached
+ to the External Bus Unit (EBU).
+
+config MTD_NAND_SUNXI
+ tristate "Support for NAND on Allwinner SoCs"
+ depends on ARCH_SUNXI
+ help
+ Enables support for NAND Flash chips on Allwinner SoCs.
+
+config MTD_NAND_HISI504
+ tristate "Support for NAND controller on Hisilicon SoC Hip04"
+ depends on HAS_DMA
+ help
+ Enables support for NAND controller on Hisilicon SoC Hip04.
+
+config MTD_NAND_QCOM
+ tristate "Support for NAND on QCOM SoCs"
+ depends on ARCH_QCOM
+ help
+ Enables support for NAND flash chips on SoCs containing the EBI2 NAND
+ controller. This controller is found on IPQ806x SoC.
+
+config MTD_NAND_MTK
+ tristate "Support for NAND controller on MTK SoCs"
+ depends on HAS_DMA
+ help
+ Enables support for NAND controller on MTK SoCs.
+ This controller is found on mt27xx, mt81xx, mt65xx SoCs.
+
+endif # MTD_NAND
diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
new file mode 100644
index 000000000000..cafde6f3d957
--- /dev/null
+++ b/drivers/mtd/nand/raw/Makefile
@@ -0,0 +1,62 @@
+#
+# linux/drivers/nand/Makefile
+#
+
+obj-$(CONFIG_MTD_NAND) += nand.o
+obj-$(CONFIG_MTD_NAND_ECC) += nand_ecc.o
+obj-$(CONFIG_MTD_NAND_BCH) += nand_bch.o
+obj-$(CONFIG_MTD_NAND_IDS) += nand_ids.o
+obj-$(CONFIG_MTD_SM_COMMON) += sm_common.o
+
+obj-$(CONFIG_MTD_NAND_CAFE) += cafe_nand.o
+obj-$(CONFIG_MTD_NAND_AMS_DELTA) += ams-delta.o
+obj-$(CONFIG_MTD_NAND_DENALI) += denali.o
+obj-$(CONFIG_MTD_NAND_DENALI_PCI) += denali_pci.o
+obj-$(CONFIG_MTD_NAND_DENALI_DT) += denali_dt.o
+obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o
+obj-$(CONFIG_MTD_NAND_BF5XX) += bf5xx_nand.o
+obj-$(CONFIG_MTD_NAND_S3C2410) += s3c2410.o
+obj-$(CONFIG_MTD_NAND_DAVINCI) += davinci_nand.o
+obj-$(CONFIG_MTD_NAND_DISKONCHIP) += diskonchip.o
+obj-$(CONFIG_MTD_NAND_DOCG4) += docg4.o
+obj-$(CONFIG_MTD_NAND_FSMC) += fsmc_nand.o
+obj-$(CONFIG_MTD_NAND_SHARPSL) += sharpsl.o
+obj-$(CONFIG_MTD_NAND_NANDSIM) += nandsim.o
+obj-$(CONFIG_MTD_NAND_CS553X) += cs553x_nand.o
+obj-$(CONFIG_MTD_NAND_NDFC) += ndfc.o
+obj-$(CONFIG_MTD_NAND_ATMEL) += atmel_nand.o
+obj-$(CONFIG_MTD_NAND_GPIO) += gpio.o
+omap2_nand-objs := omap2.o
+obj-$(CONFIG_MTD_NAND_OMAP2) += omap2_nand.o
+obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD) += omap_elm.o
+obj-$(CONFIG_MTD_NAND_CM_X270) += cmx270_nand.o
+obj-$(CONFIG_MTD_NAND_PXA3xx) += pxa3xx_nand.o
+obj-$(CONFIG_MTD_NAND_TMIO) += tmio_nand.o
+obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o
+obj-$(CONFIG_MTD_NAND_PASEMI) += pasemi_nand.o
+obj-$(CONFIG_MTD_NAND_ORION) += orion_nand.o
+obj-$(CONFIG_MTD_NAND_FSL_ELBC) += fsl_elbc_nand.o
+obj-$(CONFIG_MTD_NAND_FSL_IFC) += fsl_ifc_nand.o
+obj-$(CONFIG_MTD_NAND_FSL_UPM) += fsl_upm.o
+obj-$(CONFIG_MTD_NAND_SLC_LPC32XX) += lpc32xx_slc.o
+obj-$(CONFIG_MTD_NAND_MLC_LPC32XX) += lpc32xx_mlc.o
+obj-$(CONFIG_MTD_NAND_SH_FLCTL) += sh_flctl.o
+obj-$(CONFIG_MTD_NAND_MXC) += mxc_nand.o
+obj-$(CONFIG_MTD_NAND_SOCRATES) += socrates_nand.o
+obj-$(CONFIG_MTD_NAND_TXX9NDFMC) += txx9ndfmc.o
+obj-$(CONFIG_MTD_NAND_NUC900) += nuc900_nand.o
+obj-$(CONFIG_MTD_NAND_MPC5121_NFC) += mpc5121_nfc.o
+obj-$(CONFIG_MTD_NAND_VF610_NFC) += vf610_nfc.o
+obj-$(CONFIG_MTD_NAND_RICOH) += r852.o
+obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
+obj-$(CONFIG_MTD_NAND_JZ4780) += jz4780_nand.o jz4780_bch.o
+obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi-nand/
+obj-$(CONFIG_MTD_NAND_XWAY) += xway_nand.o
+obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash/
+obj-$(CONFIG_MTD_NAND_SUNXI) += sunxi_nand.o
+obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o
+obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand/
+obj-$(CONFIG_MTD_NAND_QCOM) += qcom_nandc.o
+obj-$(CONFIG_MTD_NAND_MTK) += mtk_nand.o mtk_ecc.o
+
+nand-objs := nand_base.o nand_bbt.o nand_timings.o
diff --git a/drivers/mtd/nand/ams-delta.c b/drivers/mtd/nand/raw/ams-delta.c
similarity index 100%
rename from drivers/mtd/nand/ams-delta.c
rename to drivers/mtd/nand/raw/ams-delta.c
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/raw/atmel_nand.c
similarity index 100%
rename from drivers/mtd/nand/atmel_nand.c
rename to drivers/mtd/nand/raw/atmel_nand.c
diff --git a/drivers/mtd/nand/atmel_nand_ecc.h b/drivers/mtd/nand/raw/atmel_nand_ecc.h
similarity index 100%
rename from drivers/mtd/nand/atmel_nand_ecc.h
rename to drivers/mtd/nand/raw/atmel_nand_ecc.h
diff --git a/drivers/mtd/nand/atmel_nand_nfc.h b/drivers/mtd/nand/raw/atmel_nand_nfc.h
similarity index 100%
rename from drivers/mtd/nand/atmel_nand_nfc.h
rename to drivers/mtd/nand/raw/atmel_nand_nfc.h
diff --git a/drivers/mtd/nand/au1550nd.c b/drivers/mtd/nand/raw/au1550nd.c
similarity index 100%
rename from drivers/mtd/nand/au1550nd.c
rename to drivers/mtd/nand/raw/au1550nd.c
diff --git a/drivers/mtd/nand/bcm47xxnflash/Makefile b/drivers/mtd/nand/raw/bcm47xxnflash/Makefile
similarity index 100%
rename from drivers/mtd/nand/bcm47xxnflash/Makefile
rename to drivers/mtd/nand/raw/bcm47xxnflash/Makefile
diff --git a/drivers/mtd/nand/bcm47xxnflash/bcm47xxnflash.h b/drivers/mtd/nand/raw/bcm47xxnflash/bcm47xxnflash.h
similarity index 100%
rename from drivers/mtd/nand/bcm47xxnflash/bcm47xxnflash.h
rename to drivers/mtd/nand/raw/bcm47xxnflash/bcm47xxnflash.h
diff --git a/drivers/mtd/nand/bcm47xxnflash/main.c b/drivers/mtd/nand/raw/bcm47xxnflash/main.c
similarity index 100%
rename from drivers/mtd/nand/bcm47xxnflash/main.c
rename to drivers/mtd/nand/raw/bcm47xxnflash/main.c
diff --git a/drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c b/drivers/mtd/nand/raw/bcm47xxnflash/ops_bcm4706.c
similarity index 100%
rename from drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c
rename to drivers/mtd/nand/raw/bcm47xxnflash/ops_bcm4706.c
diff --git a/drivers/mtd/nand/bf5xx_nand.c b/drivers/mtd/nand/raw/bf5xx_nand.c
similarity index 100%
rename from drivers/mtd/nand/bf5xx_nand.c
rename to drivers/mtd/nand/raw/bf5xx_nand.c
diff --git a/drivers/mtd/nand/brcmnand/Makefile b/drivers/mtd/nand/raw/brcmnand/Makefile
similarity index 100%
rename from drivers/mtd/nand/brcmnand/Makefile
rename to drivers/mtd/nand/raw/brcmnand/Makefile
diff --git a/drivers/mtd/nand/brcmnand/bcm63138_nand.c b/drivers/mtd/nand/raw/brcmnand/bcm63138_nand.c
similarity index 100%
rename from drivers/mtd/nand/brcmnand/bcm63138_nand.c
rename to drivers/mtd/nand/raw/brcmnand/bcm63138_nand.c
diff --git a/drivers/mtd/nand/brcmnand/bcm6368_nand.c b/drivers/mtd/nand/raw/brcmnand/bcm6368_nand.c
similarity index 100%
rename from drivers/mtd/nand/brcmnand/bcm6368_nand.c
rename to drivers/mtd/nand/raw/brcmnand/bcm6368_nand.c
diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
similarity index 100%
rename from drivers/mtd/nand/brcmnand/brcmnand.c
rename to drivers/mtd/nand/raw/brcmnand/brcmnand.c
diff --git a/drivers/mtd/nand/brcmnand/brcmnand.h b/drivers/mtd/nand/raw/brcmnand/brcmnand.h
similarity index 100%
rename from drivers/mtd/nand/brcmnand/brcmnand.h
rename to drivers/mtd/nand/raw/brcmnand/brcmnand.h
diff --git a/drivers/mtd/nand/brcmnand/brcmstb_nand.c b/drivers/mtd/nand/raw/brcmnand/brcmstb_nand.c
similarity index 100%
rename from drivers/mtd/nand/brcmnand/brcmstb_nand.c
rename to drivers/mtd/nand/raw/brcmnand/brcmstb_nand.c
diff --git a/drivers/mtd/nand/brcmnand/iproc_nand.c b/drivers/mtd/nand/raw/brcmnand/iproc_nand.c
similarity index 100%
rename from drivers/mtd/nand/brcmnand/iproc_nand.c
rename to drivers/mtd/nand/raw/brcmnand/iproc_nand.c
diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/raw/cafe_nand.c
similarity index 100%
rename from drivers/mtd/nand/cafe_nand.c
rename to drivers/mtd/nand/raw/cafe_nand.c
diff --git a/drivers/mtd/nand/cmx270_nand.c b/drivers/mtd/nand/raw/cmx270_nand.c
similarity index 100%
rename from drivers/mtd/nand/cmx270_nand.c
rename to drivers/mtd/nand/raw/cmx270_nand.c
diff --git a/drivers/mtd/nand/cs553x_nand.c b/drivers/mtd/nand/raw/cs553x_nand.c
similarity index 100%
rename from drivers/mtd/nand/cs553x_nand.c
rename to drivers/mtd/nand/raw/cs553x_nand.c
diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/raw/davinci_nand.c
similarity index 100%
rename from drivers/mtd/nand/davinci_nand.c
rename to drivers/mtd/nand/raw/davinci_nand.c
diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/raw/denali.c
similarity index 100%
rename from drivers/mtd/nand/denali.c
rename to drivers/mtd/nand/raw/denali.c
diff --git a/drivers/mtd/nand/denali.h b/drivers/mtd/nand/raw/denali.h
similarity index 100%
rename from drivers/mtd/nand/denali.h
rename to drivers/mtd/nand/raw/denali.h
diff --git a/drivers/mtd/nand/denali_dt.c b/drivers/mtd/nand/raw/denali_dt.c
similarity index 100%
rename from drivers/mtd/nand/denali_dt.c
rename to drivers/mtd/nand/raw/denali_dt.c
diff --git a/drivers/mtd/nand/denali_pci.c b/drivers/mtd/nand/raw/denali_pci.c
similarity index 100%
rename from drivers/mtd/nand/denali_pci.c
rename to drivers/mtd/nand/raw/denali_pci.c
diff --git a/drivers/mtd/nand/diskonchip.c b/drivers/mtd/nand/raw/diskonchip.c
similarity index 100%
rename from drivers/mtd/nand/diskonchip.c
rename to drivers/mtd/nand/raw/diskonchip.c
diff --git a/drivers/mtd/nand/docg4.c b/drivers/mtd/nand/raw/docg4.c
similarity index 100%
rename from drivers/mtd/nand/docg4.c
rename to drivers/mtd/nand/raw/docg4.c
diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/raw/fsl_elbc_nand.c
similarity index 100%
rename from drivers/mtd/nand/fsl_elbc_nand.c
rename to drivers/mtd/nand/raw/fsl_elbc_nand.c
diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/raw/fsl_ifc_nand.c
similarity index 100%
rename from drivers/mtd/nand/fsl_ifc_nand.c
rename to drivers/mtd/nand/raw/fsl_ifc_nand.c
diff --git a/drivers/mtd/nand/fsl_upm.c b/drivers/mtd/nand/raw/fsl_upm.c
similarity index 100%
rename from drivers/mtd/nand/fsl_upm.c
rename to drivers/mtd/nand/raw/fsl_upm.c
diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/raw/fsmc_nand.c
similarity index 100%
rename from drivers/mtd/nand/fsmc_nand.c
rename to drivers/mtd/nand/raw/fsmc_nand.c
diff --git a/drivers/mtd/nand/gpio.c b/drivers/mtd/nand/raw/gpio.c
similarity index 100%
rename from drivers/mtd/nand/gpio.c
rename to drivers/mtd/nand/raw/gpio.c
diff --git a/drivers/mtd/nand/gpmi-nand/Makefile b/drivers/mtd/nand/raw/gpmi-nand/Makefile
similarity index 100%
rename from drivers/mtd/nand/gpmi-nand/Makefile
rename to drivers/mtd/nand/raw/gpmi-nand/Makefile
diff --git a/drivers/mtd/nand/gpmi-nand/bch-regs.h b/drivers/mtd/nand/raw/gpmi-nand/bch-regs.h
similarity index 100%
rename from drivers/mtd/nand/gpmi-nand/bch-regs.h
rename to drivers/mtd/nand/raw/gpmi-nand/bch-regs.h
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c
similarity index 100%
rename from drivers/mtd/nand/gpmi-nand/gpmi-lib.c
rename to drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
similarity index 100%
rename from drivers/mtd/nand/gpmi-nand/gpmi-nand.c
rename to drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h
similarity index 100%
rename from drivers/mtd/nand/gpmi-nand/gpmi-nand.h
rename to drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-regs.h b/drivers/mtd/nand/raw/gpmi-nand/gpmi-regs.h
similarity index 100%
rename from drivers/mtd/nand/gpmi-nand/gpmi-regs.h
rename to drivers/mtd/nand/raw/gpmi-nand/gpmi-regs.h
diff --git a/drivers/mtd/nand/hisi504_nand.c b/drivers/mtd/nand/raw/hisi504_nand.c
similarity index 100%
rename from drivers/mtd/nand/hisi504_nand.c
rename to drivers/mtd/nand/raw/hisi504_nand.c
diff --git a/drivers/mtd/nand/jz4740_nand.c b/drivers/mtd/nand/raw/jz4740_nand.c
similarity index 100%
rename from drivers/mtd/nand/jz4740_nand.c
rename to drivers/mtd/nand/raw/jz4740_nand.c
diff --git a/drivers/mtd/nand/jz4780_bch.c b/drivers/mtd/nand/raw/jz4780_bch.c
similarity index 100%
rename from drivers/mtd/nand/jz4780_bch.c
rename to drivers/mtd/nand/raw/jz4780_bch.c
diff --git a/drivers/mtd/nand/jz4780_bch.h b/drivers/mtd/nand/raw/jz4780_bch.h
similarity index 100%
rename from drivers/mtd/nand/jz4780_bch.h
rename to drivers/mtd/nand/raw/jz4780_bch.h
diff --git a/drivers/mtd/nand/jz4780_nand.c b/drivers/mtd/nand/raw/jz4780_nand.c
similarity index 100%
rename from drivers/mtd/nand/jz4780_nand.c
rename to drivers/mtd/nand/raw/jz4780_nand.c
diff --git a/drivers/mtd/nand/lpc32xx_mlc.c b/drivers/mtd/nand/raw/lpc32xx_mlc.c
similarity index 100%
rename from drivers/mtd/nand/lpc32xx_mlc.c
rename to drivers/mtd/nand/raw/lpc32xx_mlc.c
diff --git a/drivers/mtd/nand/lpc32xx_slc.c b/drivers/mtd/nand/raw/lpc32xx_slc.c
similarity index 100%
rename from drivers/mtd/nand/lpc32xx_slc.c
rename to drivers/mtd/nand/raw/lpc32xx_slc.c
diff --git a/drivers/mtd/nand/mpc5121_nfc.c b/drivers/mtd/nand/raw/mpc5121_nfc.c
similarity index 100%
rename from drivers/mtd/nand/mpc5121_nfc.c
rename to drivers/mtd/nand/raw/mpc5121_nfc.c
diff --git a/drivers/mtd/nand/mtk_ecc.c b/drivers/mtd/nand/raw/mtk_ecc.c
similarity index 100%
rename from drivers/mtd/nand/mtk_ecc.c
rename to drivers/mtd/nand/raw/mtk_ecc.c
diff --git a/drivers/mtd/nand/mtk_ecc.h b/drivers/mtd/nand/raw/mtk_ecc.h
similarity index 100%
rename from drivers/mtd/nand/mtk_ecc.h
rename to drivers/mtd/nand/raw/mtk_ecc.h
diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/raw/mtk_nand.c
similarity index 100%
rename from drivers/mtd/nand/mtk_nand.c
rename to drivers/mtd/nand/raw/mtk_nand.c
diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/raw/mxc_nand.c
similarity index 100%
rename from drivers/mtd/nand/mxc_nand.c
rename to drivers/mtd/nand/raw/mxc_nand.c
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
similarity index 100%
rename from drivers/mtd/nand/nand_base.c
rename to drivers/mtd/nand/raw/nand_base.c
diff --git a/drivers/mtd/nand/nand_bbt.c b/drivers/mtd/nand/raw/nand_bbt.c
similarity index 100%
rename from drivers/mtd/nand/nand_bbt.c
rename to drivers/mtd/nand/raw/nand_bbt.c
diff --git a/drivers/mtd/nand/nand_bch.c b/drivers/mtd/nand/raw/nand_bch.c
similarity index 100%
rename from drivers/mtd/nand/nand_bch.c
rename to drivers/mtd/nand/raw/nand_bch.c
diff --git a/drivers/mtd/nand/nand_ecc.c b/drivers/mtd/nand/raw/nand_ecc.c
similarity index 100%
rename from drivers/mtd/nand/nand_ecc.c
rename to drivers/mtd/nand/raw/nand_ecc.c
diff --git a/drivers/mtd/nand/nand_ids.c b/drivers/mtd/nand/raw/nand_ids.c
similarity index 100%
rename from drivers/mtd/nand/nand_ids.c
rename to drivers/mtd/nand/raw/nand_ids.c
diff --git a/drivers/mtd/nand/nand_timings.c b/drivers/mtd/nand/raw/nand_timings.c
similarity index 100%
rename from drivers/mtd/nand/nand_timings.c
rename to drivers/mtd/nand/raw/nand_timings.c
diff --git a/drivers/mtd/nand/nandsim.c b/drivers/mtd/nand/raw/nandsim.c
similarity index 100%
rename from drivers/mtd/nand/nandsim.c
rename to drivers/mtd/nand/raw/nandsim.c
diff --git a/drivers/mtd/nand/ndfc.c b/drivers/mtd/nand/raw/ndfc.c
similarity index 100%
rename from drivers/mtd/nand/ndfc.c
rename to drivers/mtd/nand/raw/ndfc.c
diff --git a/drivers/mtd/nand/nuc900_nand.c b/drivers/mtd/nand/raw/nuc900_nand.c
similarity index 100%
rename from drivers/mtd/nand/nuc900_nand.c
rename to drivers/mtd/nand/raw/nuc900_nand.c
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/raw/omap2.c
similarity index 100%
rename from drivers/mtd/nand/omap2.c
rename to drivers/mtd/nand/raw/omap2.c
diff --git a/drivers/mtd/nand/omap_elm.c b/drivers/mtd/nand/raw/omap_elm.c
similarity index 100%
rename from drivers/mtd/nand/omap_elm.c
rename to drivers/mtd/nand/raw/omap_elm.c
diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/raw/orion_nand.c
similarity index 100%
rename from drivers/mtd/nand/orion_nand.c
rename to drivers/mtd/nand/raw/orion_nand.c
diff --git a/drivers/mtd/nand/pasemi_nand.c b/drivers/mtd/nand/raw/pasemi_nand.c
similarity index 100%
rename from drivers/mtd/nand/pasemi_nand.c
rename to drivers/mtd/nand/raw/pasemi_nand.c
diff --git a/drivers/mtd/nand/plat_nand.c b/drivers/mtd/nand/raw/plat_nand.c
similarity index 100%
rename from drivers/mtd/nand/plat_nand.c
rename to drivers/mtd/nand/raw/plat_nand.c
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/raw/pxa3xx_nand.c
similarity index 100%
rename from drivers/mtd/nand/pxa3xx_nand.c
rename to drivers/mtd/nand/raw/pxa3xx_nand.c
diff --git a/drivers/mtd/nand/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
similarity index 100%
rename from drivers/mtd/nand/qcom_nandc.c
rename to drivers/mtd/nand/raw/qcom_nandc.c
diff --git a/drivers/mtd/nand/r852.c b/drivers/mtd/nand/raw/r852.c
similarity index 100%
rename from drivers/mtd/nand/r852.c
rename to drivers/mtd/nand/raw/r852.c
diff --git a/drivers/mtd/nand/r852.h b/drivers/mtd/nand/raw/r852.h
similarity index 100%
rename from drivers/mtd/nand/r852.h
rename to drivers/mtd/nand/raw/r852.h
diff --git a/drivers/mtd/nand/s3c2410.c b/drivers/mtd/nand/raw/s3c2410.c
similarity index 100%
rename from drivers/mtd/nand/s3c2410.c
rename to drivers/mtd/nand/raw/s3c2410.c
diff --git a/drivers/mtd/nand/sh_flctl.c b/drivers/mtd/nand/raw/sh_flctl.c
similarity index 100%
rename from drivers/mtd/nand/sh_flctl.c
rename to drivers/mtd/nand/raw/sh_flctl.c
diff --git a/drivers/mtd/nand/sharpsl.c b/drivers/mtd/nand/raw/sharpsl.c
similarity index 100%
rename from drivers/mtd/nand/sharpsl.c
rename to drivers/mtd/nand/raw/sharpsl.c
diff --git a/drivers/mtd/nand/sm_common.c b/drivers/mtd/nand/raw/sm_common.c
similarity index 100%
rename from drivers/mtd/nand/sm_common.c
rename to drivers/mtd/nand/raw/sm_common.c
diff --git a/drivers/mtd/nand/sm_common.h b/drivers/mtd/nand/raw/sm_common.h
similarity index 100%
rename from drivers/mtd/nand/sm_common.h
rename to drivers/mtd/nand/raw/sm_common.h
diff --git a/drivers/mtd/nand/socrates_nand.c b/drivers/mtd/nand/raw/socrates_nand.c
similarity index 100%
rename from drivers/mtd/nand/socrates_nand.c
rename to drivers/mtd/nand/raw/socrates_nand.c
diff --git a/drivers/mtd/nand/sunxi_nand.c b/drivers/mtd/nand/raw/sunxi_nand.c
similarity index 100%
rename from drivers/mtd/nand/sunxi_nand.c
rename to drivers/mtd/nand/raw/sunxi_nand.c
diff --git a/drivers/mtd/nand/tmio_nand.c b/drivers/mtd/nand/raw/tmio_nand.c
similarity index 100%
rename from drivers/mtd/nand/tmio_nand.c
rename to drivers/mtd/nand/raw/tmio_nand.c
diff --git a/drivers/mtd/nand/txx9ndfmc.c b/drivers/mtd/nand/raw/txx9ndfmc.c
similarity index 100%
rename from drivers/mtd/nand/txx9ndfmc.c
rename to drivers/mtd/nand/raw/txx9ndfmc.c
diff --git a/drivers/mtd/nand/vf610_nfc.c b/drivers/mtd/nand/raw/vf610_nfc.c
similarity index 100%
rename from drivers/mtd/nand/vf610_nfc.c
rename to drivers/mtd/nand/raw/vf610_nfc.c
diff --git a/drivers/mtd/nand/xway_nand.c b/drivers/mtd/nand/raw/xway_nand.c
similarity index 100%
rename from drivers/mtd/nand/xway_nand.c
rename to drivers/mtd/nand/raw/xway_nand.c
diff --git a/drivers/mtd/sm_ftl.c b/drivers/mtd/sm_ftl.c
index 3692dd547879..bcc851d02440 100644
--- a/drivers/mtd/sm_ftl.c
+++ b/drivers/mtd/sm_ftl.c
@@ -17,7 +17,7 @@
#include <linux/bitops.h>
#include <linux/slab.h>
#include <linux/mtd/nand_ecc.h>
-#include "nand/sm_common.h"
+#include "nand/raw/sm_common.h"
#include "sm_ftl.h"
--
2.7.4
More information about the linux-mtd
mailing list