[PATCH v5 0/3] spi-nor: Add support for Intel SPI serial flash controller

[Lee Jones]

On Mon, 14 Nov 2016, Mika Westerberg wrote:

> This is fifth version of the series. You can find the previous versions
> archived on:
> 
>   v4: https://lwn.net/Articles/703773/
>   v3: https://lwn.net/Articles/697231/
>   v2: http://lists.infradead.org/pipermail/linux-mtd/2016-June/068277.html
>   v1: https://lkml.org/lkml/2016/6/14/269
> 
> This patch series adds support for the Intel SPI serial flash controller
> found on many recent Intel CPUs including Baytrail and Braswell. This
> driver makes it possible to access the BIOS and other platform data which
> is stored on the SPI serial flash. It is also possible to upgrade the BIOS
> using this driver if it has not been protected by special hardware bits.
> 
> The patch [1/3] includes documentation how to upgrade BIOS on MinnowBoard
> MAX.
> 
> Since poking the SPI serial flash can brick the machine, this driver can
> only be enabled when CONFIG_EXPERT=y and even then it will remain read-only
> unless instructed othwerwise by module parameter.
> 
> Changes from v4:
>   * Use INTEL_SPI_FIFO_SZ instead of hard coded value of 64 bytes
>   * Don't increment i inside call to FDATA() macro
>   * Check nor->read_opcode in intel_spi_read() and return
>     -EINVAL if not supported. We may add SFDP support later on.
> 
> Changes from v3:
>   * Added ACKs from Lee Jones.
>   * Use bus instead of dev->bus in PCI accesses
> 
> Changes from v2:
>   * Rebased on top of v4.8-rc2
>   * Updated intel_spi_read/write() according spi-nor core changes which
>     drops retlen parameter and returns number of bytes read/written.
> 
> Changes from v1:
>   * Older hardware does not support 64k erase command so added erase_64k
>     flag which is set only for Broxton (BXT).
>   * Fix protection range offset for Broxton. Now there is ispi->pregs
>     pointing to the start of the protection registers.
>   * Change naming of constants from BCR_BYT -> BYT_BCR and so on.
>   * Drop lpc_ich_finalize_spi_cell() and initialize cell directly in
>     lpc_ich_init_spi().
>   * Use info->type in switch in lpc_ich_init_spi().
>   * Add defines for magic numbers used in lpc_ich_init_spi().
>   * Use PLATFORM_DEVID_NONE with mfd_add_devices().
> 
> Mika Westerberg (3):
>   spi-nor: Add support for Intel SPI serial flash controller
>   mfd: lpc_ich: Add support for SPI serial flash host controller
>   mfd: lpc_ich: Add support for Intel Apollo Lake SoC

What's the plan for this set?

>  Documentation/mtd/intel-spi.txt          |  88 ++++
>  drivers/mfd/lpc_ich.c                    | 131 +++++
>  drivers/mtd/spi-nor/Kconfig              |  20 +
>  drivers/mtd/spi-nor/Makefile             |   2 +
>  drivers/mtd/spi-nor/intel-spi-platform.c |  57 +++
>  drivers/mtd/spi-nor/intel-spi.c          | 791 +++++++++++++++++++++++++++++++
>  drivers/mtd/spi-nor/intel-spi.h          |  24 +
>  include/linux/mfd/lpc_ich.h              |   3 +
>  include/linux/platform_data/intel-spi.h  |  31 ++
>  9 files changed, 1147 insertions(+)
>  create mode 100644 Documentation/mtd/intel-spi.txt
>  create mode 100644 drivers/mtd/spi-nor/intel-spi-platform.c
>  create mode 100644 drivers/mtd/spi-nor/intel-spi.c
>  create mode 100644 drivers/mtd/spi-nor/intel-spi.h
>  create mode 100644 include/linux/platform_data/intel-spi.h
> 

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog