[PATCH v3 2/9] mtd: spi-nor: add an alternative method to support memory >16MiB
Cyrille Pitchen
cyrille.pitchen at atmel.com
Wed Nov 2 03:49:21 PDT 2016
Hi,
Le 31/10/2016 à 19:51, Jagan Teki a écrit :
> Hi Cyrille,
>
> On Mon, Oct 24, 2016 at 10:04 PM, Cyrille Pitchen
> <cyrille.pitchen at atmel.com> wrote:
>> This patch provides an alternative mean to support memory above 16MiB
>> (128Mib) by replacing 3byte address op codes by their associated 4byte
>> address versions.
>>
>> Using the dedicated 4byte address op codes doesn't change the internal
>> state of the SPI NOR memory as opposed to using other means such as
>> updating a Base Address Register (BAR) and sending command to enter/leave
>> the 4byte mode.
>>
>> Hence when a CPU reset occurs, early bootloaders don't need to be aware
>> of BAR value or 4byte mode being enabled: they can still access the first
>> 16MiB of the SPI NOR memory using the regular 3byte address op codes.
>>
>> Signed-off-by: Cyrille Pitchen <cyrille.pitchen at atmel.com>
>> Tested-by: Vignesh R <vigneshr at ti.com>
>> ---
>> drivers/mtd/devices/serial_flash_cmds.h | 7 ---
>> drivers/mtd/devices/st_spi_fsm.c | 28 ++++-----
>> drivers/mtd/spi-nor/spi-nor.c | 104 +++++++++++++++++++++++++-------
>> include/linux/mtd/spi-nor.h | 22 +++++--
>> 4 files changed, 113 insertions(+), 48 deletions(-)
>>
>> diff --git a/drivers/mtd/devices/serial_flash_cmds.h b/drivers/mtd/devices/serial_flash_cmds.h
>> index f59a125295d0..8b81e15105dd 100644
>> --- a/drivers/mtd/devices/serial_flash_cmds.h
>> +++ b/drivers/mtd/devices/serial_flash_cmds.h
>> @@ -18,19 +18,12 @@
>> #define SPINOR_OP_RDVCR 0x85
>>
>> /* JEDEC Standard - Serial Flash Discoverable Parmeters (SFDP) Commands */
>> -#define SPINOR_OP_READ_1_2_2 0xbb /* DUAL I/O READ */
>> -#define SPINOR_OP_READ_1_4_4 0xeb /* QUAD I/O READ */
>> -
>> #define SPINOR_OP_WRITE 0x02 /* PAGE PROGRAM */
>> #define SPINOR_OP_WRITE_1_1_2 0xa2 /* DUAL INPUT PROGRAM */
>> #define SPINOR_OP_WRITE_1_2_2 0xd2 /* DUAL INPUT EXT PROGRAM */
>> #define SPINOR_OP_WRITE_1_1_4 0x32 /* QUAD INPUT PROGRAM */
>> #define SPINOR_OP_WRITE_1_4_4 0x12 /* QUAD INPUT EXT PROGRAM */
>>
>> -/* READ commands with 32-bit addressing */
>> -#define SPINOR_OP_READ4_1_2_2 0xbc
>> -#define SPINOR_OP_READ4_1_4_4 0xec
>> -
>> /* Configuration flags */
>> #define FLASH_FLAG_SINGLE 0x000000ff
>> #define FLASH_FLAG_READ_WRITE 0x00000001
>> diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c
>> index 5454b4113589..804313a33f2b 100644
>> --- a/drivers/mtd/devices/st_spi_fsm.c
>> +++ b/drivers/mtd/devices/st_spi_fsm.c
>> @@ -507,13 +507,13 @@ static struct seq_rw_config n25q_read3_configs[] = {
>> * - 'FAST' variants configured for 8 dummy cycles (see note above.)
>> */
>> static struct seq_rw_config n25q_read4_configs[] = {
>> - {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ4_1_4_4, 0, 4, 4, 0x00, 0, 8},
>> - {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8},
>> - {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ4_1_2_2, 0, 2, 2, 0x00, 0, 8},
>> - {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8},
>> - {FLASH_FLAG_READ_FAST, SPINOR_OP_READ4_FAST, 0, 1, 1, 0x00, 0, 8},
>> - {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ4, 0, 1, 1, 0x00, 0, 0},
>> - {0x00, 0, 0, 0, 0, 0x00, 0, 0},
>> + {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B, 0, 4, 4, 0x00, 0, 8},
>> + {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B, 0, 1, 4, 0x00, 0, 8},
>> + {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B, 0, 2, 2, 0x00, 0, 8},
>> + {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B, 0, 1, 2, 0x00, 0, 8},
>> + {FLASH_FLAG_READ_FAST, SPINOR_OP_READ_FAST_4B, 0, 1, 1, 0x00, 0, 8},
>> + {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ_4B, 0, 1, 1, 0x00, 0, 0},
>> + {0x00, 0, 0, 0, 0, 0x00, 0, 0},
>> };
>>
>> /*
>> @@ -553,13 +553,13 @@ static int stfsm_mx25_en_32bit_addr_seq(struct stfsm_seq *seq)
>> * entering a state that is incompatible with the SPIBoot Controller.
>> */
>> static struct seq_rw_config stfsm_s25fl_read4_configs[] = {
>> - {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ4_1_4_4, 0, 4, 4, 0x00, 2, 4},
>> - {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8},
>> - {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ4_1_2_2, 0, 2, 2, 0x00, 4, 0},
>> - {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8},
>> - {FLASH_FLAG_READ_FAST, SPINOR_OP_READ4_FAST, 0, 1, 1, 0x00, 0, 8},
>> - {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ4, 0, 1, 1, 0x00, 0, 0},
>> - {0x00, 0, 0, 0, 0, 0x00, 0, 0},
>> + {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B, 0, 4, 4, 0x00, 2, 4},
>> + {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B, 0, 1, 4, 0x00, 0, 8},
>> + {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B, 0, 2, 2, 0x00, 4, 0},
>> + {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B, 0, 1, 2, 0x00, 0, 8},
>> + {FLASH_FLAG_READ_FAST, SPINOR_OP_READ_FAST_4B, 0, 1, 1, 0x00, 0, 8},
>> + {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ_4B, 0, 1, 1, 0x00, 0, 0},
>> + {0x00, 0, 0, 0, 0, 0x00, 0, 0},
>> };
>>
>> static struct seq_rw_config stfsm_s25fl_write4_configs[] = {
>> diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
>> index 5c87b2d99507..423448c1c7a8 100644
>> --- a/drivers/mtd/spi-nor/spi-nor.c
>> +++ b/drivers/mtd/spi-nor/spi-nor.c
>> @@ -75,6 +75,10 @@ struct flash_info {
>> * bit. Must be used with
>> * SPI_NOR_HAS_LOCK.
>> */
>> +#define SPI_NOR_4B_OPCODES BIT(10) /*
>> + * Use dedicated 4byte address op codes
>> + * to support memory size above 128Mib.
>> + */
>> };
>>
>> #define JEDEC_MFR(info) ((info)->id[0])
>> @@ -188,6 +192,81 @@ static inline struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd)
>> return mtd->priv;
>> }
>>
>> +
>> +struct spi_nor_address_entry {
>> + u8 src_opcode;
>> + u8 dst_opcode;
>> +};
>> +
>> +static u8 spi_nor_convert_opcode(u8 opcode,
>> + const struct spi_nor_address_entry *entries,
>> + size_t num_entries)
>> +{
>> + int min, max;
>> +
>> + min = 0;
>> + max = num_entries - 1;
>> + while (min <= max) {
>> + int mid = (min + max) >> 1;
>> + const struct spi_nor_address_entry *entry = &entries[mid];
>> +
>> + if (opcode == entry->src_opcode)
>> + return entry->dst_opcode;
>> +
>> + if (opcode < entry->src_opcode)
>> + max = mid - 1;
>> + else
>> + min = mid + 1;
>> + }
>> +
>> + /* No conversion found */
>> + return opcode;
>> +}
>> +
>> +static u8 spi_nor_3to4_opcode(u8 opcode)
>> +{
>> + /* MUST be sorted by 3byte opcode */
>> +#define ENTRY_3TO4(_opcode) { _opcode, _opcode##_4B }
>> + static const struct spi_nor_address_entry spi_nor_3to4_table[] = {
>> + ENTRY_3TO4(SPINOR_OP_PP), /* 0x02 */
>> + ENTRY_3TO4(SPINOR_OP_READ), /* 0x03 */
>> + ENTRY_3TO4(SPINOR_OP_READ_FAST), /* 0x0b */
>> + ENTRY_3TO4(SPINOR_OP_BE_4K), /* 0x20 */
>> + ENTRY_3TO4(SPINOR_OP_PP_1_1_4), /* 0x32 */
>> + ENTRY_3TO4(SPINOR_OP_PP_1_4_4), /* 0x38 */
>> + ENTRY_3TO4(SPINOR_OP_READ_1_1_2), /* 0x3b */
>> + ENTRY_3TO4(SPINOR_OP_BE_32K), /* 0x52 */
>> + ENTRY_3TO4(SPINOR_OP_READ_1_1_4), /* 0x6b */
>> + ENTRY_3TO4(SPINOR_OP_READ_1_2_2), /* 0xbb */
>> + ENTRY_3TO4(SPINOR_OP_SE), /* 0xd8 */
>> + ENTRY_3TO4(SPINOR_OP_READ_1_4_4), /* 0xeb */
>> + };
>> +#undef ENTRY_3TO4
>> +
>> + return spi_nor_convert_opcode(opcode, spi_nor_3to4_table,
>> + ARRAY_SIZE(spi_nor_3to4_table));
>> +}
>> +
>> +static void spi_nor_set_4byte_opcodes(struct spi_nor *nor,
>> + const struct flash_info *info)
>> +{
>> + /* Do some manufacturer fixups first */
>> + switch (JEDEC_MFR(info)) {
>> + case SNOR_MFR_SPANSION:
>> + /* No small sector erase for 4-byte command set */
>> + nor->erase_opcode = SPINOR_OP_SE;
>> + nor->mtd.erasesize = info->sector_size;
>> + break;
>> +
>> + default:
>> + break;
>> + }
>> +
>> + nor->read_opcode = spi_nor_3to4_opcode(nor->read_opcode);
>> + nor->program_opcode = spi_nor_3to4_opcode(nor->program_opcode);
>> + nor->erase_opcode = spi_nor_3to4_opcode(nor->erase_opcode);
>> +}
>> +
>> /* Enable/disable 4-byte addressing mode. */
>> static inline int set_4byte(struct spi_nor *nor, const struct flash_info *info,
>> int enable)
>> @@ -1476,27 +1555,10 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
>> else if (mtd->size > 0x1000000) {
>> /* enable 4-byte addressing if the device exceeds 16MiB */
>> nor->addr_width = 4;
>> - if (JEDEC_MFR(info) == SNOR_MFR_SPANSION) {
>> - /* Dedicated 4-byte command set */
>> - switch (nor->flash_read) {
>> - case SPI_NOR_QUAD:
>> - nor->read_opcode = SPINOR_OP_READ4_1_1_4;
>> - break;
>> - case SPI_NOR_DUAL:
>> - nor->read_opcode = SPINOR_OP_READ4_1_1_2;
>> - break;
>> - case SPI_NOR_FAST:
>> - nor->read_opcode = SPINOR_OP_READ4_FAST;
>> - break;
>> - case SPI_NOR_NORMAL:
>> - nor->read_opcode = SPINOR_OP_READ4;
>> - break;
>> - }
>> - nor->program_opcode = SPINOR_OP_PP_4B;
>> - /* No small sector erase for 4-byte command set */
>> - nor->erase_opcode = SPINOR_OP_SE_4B;
>> - mtd->erasesize = info->sector_size;
>> - } else
>> + if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
>> + info->flags & SPI_NOR_4B_OPCODES)
>> + spi_nor_set_4byte_opcodes(nor, info);
>
> I am giving my inputs based on the discussion on this thread[1].
>
> Seems like winbond[2], stmicron, spansion look better way or equally
> same for accessing 4-byte addressing commands. and I find few of the
> Macronix [3] have support of 4B addressing(see Table 5) but
> lack/unable to find the 4B opcodes.
>
The Macronix mx25l25635e has no 4-byte address op codes. Instead you can
use the EN4B (enter 4-byte mode) B7h op code to make the memory enter its
4-byte mode: hence you still write one of the 3-byte address op code but now
this op code is followed by a 4-byte address.
Currently the spi-nor framework uses this EN4B op code for all but Spansion
memories. However entering this 4-byte mode is statefull.
For the Macronix 35e won't be able to use the 4-byte address instruction set
and we will keep on entering the 4-byte mode.
The idea behind the patch is to use the 4-byte address instruction set when
we are absolutely sure this set is supported by a given memory but keep the
current behaviour for other memories.
> And about BAR support, based on my experience in u-boot and research
> on above chips only require when controller isn't supporting 4-byte
> addressing even if connected flash chip has > 16MiB, that means there
> is no exact or equivalent requirement for flash side either.
>
> So, adding the flags on flash table might be the good option instead
> making code to convert 3B opcode to 4B because anyway the chips
> require SPI_NOR_4B_OPCODES and also except winbond, stmicron, spansion
> not too many flash needed > 16MiB support as of now.
>
Sorry but I don't understand what you mean or suggest here!
> [1] https://lkml.org/lkml/2016/10/24/276
> [2] https://www.winbond.com/resource-files/w25q256fv_revg1_120214_qpi_website_rev_g.pdf
> [3] http://www.zlgmcu.com/mxic/pdf/NOR_Flash_c/MX25L25635E_DS_EN.pdf
>
> thanks!
>
More information about the linux-mtd
mailing list