[PATCH] mtd: spi-nor: Add support for ISSI is25lp128

[Brian Norris]

Hi Gabor,

On Tue, Mar 08, 2016 at 06:26:41PM +0100, Gabor Juhos wrote:
> > On Tue, Feb 09, 2016 at 09:12:43PM +0300, Nikita Nazarenko wrote:
> >> Signed-off-by: Nikita Nazarenko <nnazarenko at radiofid.com>
> >> ---
> >>  drivers/mtd/spi-nor/spi-nor.c | 1 +
> >>  1 file changed, 1 insertion(+)
> >>
> >> diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
> >> index ed0c19c..e0bb151 100644
> >> --- a/drivers/mtd/spi-nor/spi-nor.c
> >> +++ b/drivers/mtd/spi-nor/spi-nor.c
> >> @@ -739,6 +739,7 @@ static const struct flash_info spi_nor_ids[] = {
> >>  
> >>  	/* ISSI */
> > 
> > Both of these ISSI entries look wrong.
> > 
> >>  	{ "is25cd512", INFO(0x7f9d20, 0, 32 * 1024,   2, SECT_4K) },
> > 
> > Looking at the datasheet for this part [1], shouldn't the ID be
> > 0x9d7f20 (i.e., the MFR ID is 0x9d, not 0x7f)? That would match the
> > existing CFI definition for "PMC". And IIUC, PMC got bought by ISSI? Or
> > some kind of merger, I don't follow these things.
> 
> The ID is definitely 0x7d9d20, the m28p80 driver detects the device correctly
> with that:
> 
>   m25p80 spi0.0: found is25cd512, expected m25p80
>   m25p80 spi0.0: is25cd512 (64 Kbytes)
>   Creating 4 MTD partitions on "spi0.0":
>   0x000000000000-0x00000000c000 : "routerboot"
>   0x00000000c000-0x00000000d000 : "hard_config"
>   0x00000000d000-0x00000000e000 : "bios"
>   0x00000000e000-0x00000000f000 : "soft_config"
> 
> The first byte of the manufacturer ID is indeed 0x9d, but the device returns
> that as the second byte throught the JEDEC ID READ command. Even though it is a
> weird behaviour, it is described on page 11 of the datasheet.

What a stupid implementation. And they changed it to the sane
implementation for is25lp128 it seems?

> >> +	{ "is25lp128", INFO(0x9d6018, 0, 32 * 1024,   512, SECT_4K) },
> > 
> > This datasheet [1] says that for SPI mode (not QPI mode), 4K erase is
> > done with opcode 0xD7 (i.e., SPINOR_OP_BE_4K_PMC) not 0x20
> > (SPINOR_OP_BE_4K). So we would need the SECT_4K_PMC, not the SECT_4K
> > flag.
> 
> I don't have a board with such flash device, but Table 8.1 "Instruction Set" is
> misleading a bit. In my understanding, erasing 4K sectors should work with both
> commands. Look at Clause 8.10 "SECTOR ERASE OPERATION (SER, D7h/20h)" on page 33
> in the datasheet. Both Figure 8.12 "Sector Erase Sequence" and Figure 8.13
> "Sector Erase Sequence (QPI) " says 'D7h/20h'.

Ah, I could see how the table could be read either way. I expect that
the submitter (Nikita) should be able to confirm this through testing.

> > Also, the datasheet for this device says it supports 64K sectors, and
> > the 32K sectors require a different erase command (SPINOR_OP_BE_32K; not
> > currently supported in this driver). Did you test erase to be sure it
> > worked as expected? Or are one or more datasheets wrong?
> 
> It seems that you are correct about this.

To be clear, it looks like your submission (is25cd512) does use D8h for
32K erase blocks, since it's such a tiny device. But Nikita's device
appears to use 64K erase blocks.

I expect Nikita can test and resubmit a revised entry here.

Regards,
Brian