[PATCH] mtd: nandsim: use the existing output macros

[Richard Weinberger]

On Sun, Jun 12, 2016 at 12:18 PM, Mathias Kresin <dev at kresin.me> wrote:
> Without using the output macros, it isn't possible to suppress these
> messages on the console by specifying an appropriate console log level.
>
> Signed-off-by: Mathias Kresin <dev at kresin.me>
> ---
>  drivers/mtd/nand/nandsim.c | 28 ++++++++++++++--------------
>  1 file changed, 14 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/mtd/nand/nandsim.c b/drivers/mtd/nand/nandsim.c
> index 1eb9344..3cfcc5e 100644
> --- a/drivers/mtd/nand/nandsim.c
> +++ b/drivers/mtd/nand/nandsim.c
> @@ -769,22 +769,22 @@ static int __init init_nandsim(struct mtd_info *mtd)
>         if (ns->busw == 16)
>                 NS_WARN("16-bit flashes support wasn't tested\n");
>
> -       printk("flash size: %llu MiB\n",
> +       NS_INFO("flash size: %llu MiB\n",
>                         (unsigned long long)ns->geom.totsz >> 20);
> -       printk("page size: %u bytes\n",         ns->geom.pgsz);
> -       printk("OOB area size: %u bytes\n",     ns->geom.oobsz);
> -       printk("sector size: %u KiB\n",         ns->geom.secsz >> 10);
> -       printk("pages number: %u\n",            ns->geom.pgnum);
> -       printk("pages per sector: %u\n",        ns->geom.pgsec);
> -       printk("bus width: %u\n",               ns->busw);
> -       printk("bits in sector size: %u\n",     ns->geom.secshift);
> -       printk("bits in page size: %u\n",       ns->geom.pgshift);
> -       printk("bits in OOB size: %u\n",        ffs(ns->geom.oobsz) - 1);
> -       printk("flash size with OOB: %llu KiB\n",
> +       NS_INFO("page size: %u bytes\n",         ns->geom.pgsz);
> +       NS_INFO("OOB area size: %u bytes\n",     ns->geom.oobsz);
> +       NS_INFO("sector size: %u KiB\n",         ns->geom.secsz >> 10);
> +       NS_INFO("pages number: %u\n",            ns->geom.pgnum);
> +       NS_INFO("pages per sector: %u\n",        ns->geom.pgsec);
> +       NS_INFO("bus width: %u\n",               ns->busw);
> +       NS_INFO("bits in sector size: %u\n",     ns->geom.secshift);
> +       NS_INFO("bits in page size: %u\n",       ns->geom.pgshift);
> +       NS_INFO("bits in OOB size: %u\n",       ffs(ns->geom.oobsz) - 1);
> +       NS_INFO("flash size with OOB: %llu KiB\n",
>                         (unsigned long long)ns->geom.totszoob >> 10);
> -       printk("page address bytes: %u\n",      ns->geom.pgaddrbytes);
> -       printk("sector address bytes: %u\n",    ns->geom.secaddrbytes);
> -       printk("options: %#x\n",                ns->options);
> +       NS_INFO("page address bytes: %u\n",      ns->geom.pgaddrbytes);
> +       NS_INFO("sector address bytes: %u\n",    ns->geom.secaddrbytes);
> +       NS_INFO("options: %#x\n",                ns->options);

Makes sense. I'll carry this since I'm doing a bigger nandsim facelift.

-- 
Thanks,
//richard